Festo EAPR-E11-30 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Festo EAPR-E11-30 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Montageanleitung (Original: de)
8025126
1305NH
†‡
Sensorbefestigung
EAPR-E11-30
Festo SE & Co. KG
Postfach
73726 Esslingen
Deutschland
+49 711 347-0
www.festo.com
1. Teileliste
18930d_1
Sensorbefestigung
EAPR-E11-30:
1 Sensorhalter
(Nut 8)
2 Schaltfahne
Y-Hub
3 Schaltfahne
X-Hub
4 Senkschraube
M3x6
5 Zylinderschraube
M2,5x5
6 Scheibe
B2,7
(1x)
(1x)
(1x)
(2x)
(4x)
(4x)
Nicht im Lieferumfang:
18930d_2
7 Flächenportal
EXCM-30
8 Näherungsschalter
( Zubehör)
(1x)
(2x)
18930d_3
Bestimmungsgemäß dient die Sensorbefestigung dazu die Näherungs-
schalter 8 als Referenzschalter am Flächenportal 7 zu befestigen.
Wählen Sie bitte das entsprechende Zubehör aus unserem Katalog
( www.festo.com/catalogue).
2. Montage
18930d_4
ï‚·Platzieren Sie den Sensor-
halter 1 am Flächen-
portal 7.
ï‚·Drehen Sie die Schrau-
ben 4 fest.
Halten Sie das zulässige An-
ziehdrehmoment ein.
18930d_5
ï‚·Platzieren Sie die Schalt-
fahne 2 am Schlitten (A)
des Flächenportals 7.
ï‚·Verwenden Sie die Schei-
ben 6.
ï‚·Drehen Sie die Schrau-
ben 5 zunächst nur leicht
an.
18930d_6
ï‚·Platzieren Sie die Schalt-
fahne 3 an der Y-Achse des
Flächenportals 7.
ï‚·Verwenden Sie die Schei-
ben 6.
ï‚·Drehen Sie die Schrau-
ben 5 zunächst nur leicht
an.
18930d_8
Beim Flächenportal 7 existie-
ren 2 Montagevarianten:
– (U) Motor unten
– (O) Motor oben
Montieren Sie die Nähe-
rungsschalter 8 so, dass
der Kabelabgang der Nähe-
rungsschalter in Richtung
Motor zeigt.
18930d_7
Positionieren Sie die Nähe-
rungsschalter 8 bei beiden
Montagevarianten zunächst
so, dass die Näherungs-
schalter 8 wie folgt im
Sensorhalter 1 ausge-
richtet sind:
– Y-Hub: oben bündig
– X-Hub: unten bündig
Beachten Sie die zugehöri-
gen Bedienungsanleitungen
der Näherungsschalter.
18930d_9
ï‚·Justieren Sie die Schaltfah-
nen 2 und 3 über die
Langlöcher, bis die Nähe-
rungsschalter sicher schal-
ten.
ï‚·Drehen Sie die Schrau-
ben 5 fest.
Halten Sie das zulässige An-
ziehdrehmoment ein.
1
2
3
4
5
6
1
4
1,2 Nm _ 10 %
7
7
6
5
2
5
6
3
U
8
8
O
8
Y
X
3
5
0,8 Nm
_ 10 %
0,8 Nm
_ 10 %
2
5
Y
X
Y
X
7
8
A
Assembly instructions (original: de)
8025126
1305NH
†‡
Sensor mounting
EAPR-E11-30
Festo SE & Co. KG
Postfach
73726 Esslingen
Germany
+49 711 347-0
www.festo.com
1. Parts list
18930d_1
Sensor mounting
EAPR-E11-30:
1 Sensor bracket
(slot 8)
2 Switch lug
Y-stroke
3 Switch lug
X-stroke
4 Countersunk screw
M3x6
5 Socket head screw
M2.5x5
6 Washer
B2.7
(1x)
(1x)
(1x)
(2x)
(4x)
(4x)
Not included in delivery:
18930d_2
7 Planar surface gan-
try
EXCM-30
8 Proximity sensor
( Accessories)
(1x)
(2x)
18930d_3
The sensor mounting is intended to be used to fasten the proximity sen-
sor 8 as reference switch to the planar surface gantry 7.
ï‚·Please select the corresponding accessories from our catalogue
( www.festo.com/catalogue).
2. Assembly
18930d_4
ï‚·Place the sensor bracket 1
on the planar surface gan-
try 7.
ï‚·Tighten the screws 4.
Comply with the permissible
tightening torque.
18930d_5
ï‚·Place the switch lug 2 on
the slide (A) of the planar
surface gantry 7.
ï‚·Use the washers 6.
ï‚·Tighten the screws 5 only
lightly at first.
18930d_6
ï‚·Place the switch lug 3 on
the Y-axis of the planar sur-
face gantry 7.
ï‚·Use the washers 6.
ï‚·Tighten the screws 5 only
lightly at first.
18930d_8
For the planar surface gan-
try 7, there are 2 mounting
variants:
– (U) Motor underneath
– (O) Motor on top
ï‚·Mount the proximity sen-
sor 8 so that the cable out-
let of the proximity sensor
points in the direction of the
motor.
18930d_7
ï‚·With both mounting vari-
ants, first position the prox-
imity sensors 8 so that the
proximity sensors 8 are
aligned in the sensor
bracket 1 as follows:
– Y-stroke: on top, flush
– X-stroke: underneath, flush
ï‚·Observe the relevant oper-
ating instructions for the
proximity sensors.
18930d_9
ï‚·Adjust the switch lugs 2
and 3 via the elongated
holes until the proximity
sensors switch reliably.
ï‚·Tighten the screws 5
.
Comply with the permissible
tightening torque.
1
2
3
4
5
6
1
4
1.2 Nm _ 10 %
7
7
6
5
2
5
6
3
U
8
8
O
8
Y
X
3
5
0.8 Nm
_ 10 %
0.8 Nm
_ 10 %
2
5
Y
X
Y
X
7
8
A


Produktspezifikationen

Marke: Festo
Kategorie: Nicht kategorisiert
Modell: EAPR-E11-30

Brauchst du Hilfe?

Wenn Sie Hilfe mit Festo EAPR-E11-30 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Festo

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-