FERM BGM1010 - FBSM 150-50 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für FERM BGM1010 - FBSM 150-50 (16 Seiten) in der Kategorie Sander. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/16
Ferm B.V. • P.O. Box 134 • 8280 AC Genemuiden-NL • Internet: www.ferm.com 0106/27
Ferm FBSM-150/50
Belt sander/grinder
Bandschleif/Schleifmachine
Bandschuur/slijpmachine
Tourét à meuler/poncer
Máquina lijadora/afiladora
∆·ÈÓÈÔÏÂÈ·ÓÙ‹Ú·˜/∆ÚÔ¯fi˜ §Â›·ÓÛ˘
Art. nr: 350350
USERS MANUAL
BEDIENUNGSANLEITUNG
GEBRUIKSAANWIJZING
MODE D’EMPLOI
MODEO DE EMPLEO
√¢∏°π∂™ Ã∏™∂ø™
Ferm 31
Product: Ferm Belt sander/grinder
Type FBSM-150/50, art.nr. 350350
Ferm, Genemuiden, The Netherlands
Sound pressure level 76 dB(A)
In order to prevent overheating and possi-
ble damages to the engine, use the machine
intermittently, for periods of 30 minutes.
CAREFULLY READ THE INSTRUCTIONS
BEFORE YOU USE THE BELT SANDER/-
GRINDER!
1. GENERAL SAFETY RULES
Keep the work area clean.
- A cluttered work area may cause accidents.
- Make sure the work area is well lit.
Work environment.
Never leave tools in the rain. Do not use tools
in damp or wet places. Never use tools near in-
flammable liquids or gasses.
Prevent electrical shock.
Keep the power cord away from heat, oil and
sharp edges. Avoid skin contact with exposed
parts of the power cord or plug. Damaged parts
must be replaced immediately.
Keep children away.
Never allow children or spectators to touch the
tools, keep them at a safe distance from the
work area.
Store tools in a safe place.
Tools that are not used must be stored in a dry
and locked placed, out of the reach of children.
Do not force the tool.
The machine will do the job better and safer at
the rate for which it was intended. Damage cau-
sed by forcing the tool is not covered by the
warranty.
Use the right type of tool.
Do not use low-powered tools for heavy-duty
operations. Never use the machine other than
for its intended purpose.
Wear suitable clothing.
- Do not wear loose clothing or jewellery that
might get caught in moving parts;
- Never wear rings with protruding parts;
- Cover long hair;
Wear safety glasses, mouth and ear protection.
Wear personal protection while working.
Cable.
Never carry the tool by its cable and do not tug
at the cable to pull the plug from the socket.
Keep the cable away from heat, oil and sharp
edges.
Always clamp the work.
Always clamp the work against the bench.
Never
work on objects that are too small to hold.
Posture.
- Do not over each. Be sure of your footing and
balance at all times;
- Do not over reach on ladders or scaffold.
Maintain the tool with care.
- The tool works best and safest if it is kept clean.
- Observe the instructions for maintenance and
changing accessories. Keep the tool dry and free
from oil and grease.
Disconnect the machine.
Disconnect the machine when you do not use it,
before cleaning and when changing accessories
and tools.
Remove wrenches from the machine.
Before starting the machine, make sure to
remove wrenches and other tools.
Avoid unintentional starting.
Never carry the plugged-in machine with your
finger on the switch. Make sure the switch is off
when the machine is plugged in.
Extension cable for outdoor use.
When working outdoors use only extension cables
suitable for this purpose and marked as such.
When using machines with earth connection, use
an extension cable with earth connection.
Stay alert.
Watch what you are doing, use your common
sense, do not operate the tool when you cannot
concentrate on the job.
Check the machine for damage.
- Before starting the machine, check that all safety
devices operate properly;
- Make sure all moving parts are in good working
order. Check the machine for any broken or
!
GB English
230V~ 240 W N0= 686 x 50 Ø 150 x Ø 12,7 mm
50Hz 2950/min mm 20 mm
2Ferm
1'
AVAILABLE SPARE PARTS FOR FBSM-150/50
REF.NR. DESCRIPTION FERM NR.
1 PROTECTION GLASS 206401
4 SUPPORT LEFT 206152
5 RUBBER FOOT 206411
6 SWITCH 206451
9 FIXING KNOB 206157
11 SPRING 206158
15 ROTATION WHEEL 206156
16 DRIVING WHEEL 206155
18 PROTECTION GLASS HOLDER 206154
30 Ferm
jamming parts, make sure all parts are fitted pro-
perly and any other conditions that might affect
the functioning of the machine are favourable;
- If not stated otherwise in this manual, damaged
safety devices and machine parts must be repai-
red or replaced by a recognized service centre.
Damaged switches must be replaced by a service
centre. Do not use the machine when it cannot
be switched on or off.
Have your tool repaired by an expert!
This electric appliance is in accordance with the
relevant safety rules. Repairing of electric applian-
ces may be carried out only by experts other wise
it may cause considerable danger for the user.
For your own safety use only accessories
and attachments recommended in this
manual or the catalogue. The use of other
than the stated accessories or attach-
ments may cause injuries.
2. SPECIFIC SAFETY RULES
BEFORE USING THE MACHINE:
1. Check the following points:
- do the voltage of the engine and the engine
safeguard, if any, correspond to the mains
voltage (appliances for a mains voltage of
230V~50Hz can be connected to a mains vol-
tage of 220V~50Hz without any problems);
- use an earthed power source (wall socket);
- are the mains lead and the mains plug in a good
condition: strong, without ravels or damages;
- is the Belt sander/grinder well mounted on a
work bench;
2. For functional reasons the turning parts of this
machine are not covered. Therefore it is of
utmost importance to be careful. Hold the
workpiece firmly, to prevent it from slipping
from your hands. Never touch the sanding or
grinding surfaces with your hands.
3. A grinding stone is fragile. The stone is easily
damaged when being dropped, hit, etc. Always
grind with the face of the grinding stone, never the
sides. Acracked grinding stone must be replaced
immediately. Due to the high rotational velocity
the stone might disintegrate, causing accidents.
4. Always wear safety classes during sanding and
grinding.
5. Never operate the grinding machine without the
guard in place.
6. The maximum clearance between the tool rest
and the grinding stone must never exceed 1-1.5
mm. The belt of the belt sander should just be
cleared from the tool rest.
7. Use the grinding stone only for its intended pur-
pose, e.g. for grinding tools, never for heavy-
duty construction work.
8. Never rebore the arbor hole in the grinding sto-
ne to widen the diameter.
WHEN USING THE MACHINE:
1. Check if the switch is not in the ON position (1)
before the mains plug is connected to the mains
voltage.
2. Always keep the mains cable away from moving
parts of the machine.
3. Use safety glasses.
4. Use a dust mask.
IMMEDIATELY SWITCH OFF THE MACHI-
NE IN CASE OF:
1. a overheated machine;
2. malfunction of the mainsplug, -socket or dama-
ged cables;
3. defective switch;
4. smoke or smell caused by scorched insulation.
3. ENVIRONMENTAL PROTECTION
Recycling raw materials is prefered to dumping them
as waste. To prevent the machine from being damaged
during transport its packing must be strong. Insofar as
possible the packing consists of recyclable materials
such as paper, cardboard and wood.
4. FERM’S AFTER SALES SERVICE
Save the original packing. Should you ever have to
move the Belt sander/grinder there is less risk of
damage in the original packing. Should your Belt san-
der/grinder become defective, please consult your
local Ferm dealer.
5. INSTALLATION
1. The Belt sander/grinder is fitted with a three-
core cable and earthed plug. Therefore, always
connect the plug to an earthed socket.
2. Try to avoid the use of long extension cables. If
you have to use an extension cable, make sure it
is 3 core and fitted with an earthed plug and
connector.
3. The Belt sander/grinder has to be secured to
the bench by means of bolts. The length of the
bolts depends on the thickness of the bench.
6. DESCRIPTION
THE NUMBERS BELOW REFER TO THE
ILLUSTRATION ON PAGE 30:
DESCRIPTION:
1. Cover glass;
2. Guard for grinding stone;
3. Grinding stone;
4. Tool rest;
!
Ferm 3
Description
Beschreibung
Beschrijving
Description
Fig. 1
Fig. 2 Fig. 3 Fig. 4
Produktspezifikationen
| Marke: | FERM |
| Kategorie: | Sander |
| Modell: | BGM1010 - FBSM 150-50 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit FERM BGM1010 - FBSM 150-50 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sander FERM
22 September 2024
5 August 2024
3 August 2024
1 August 2024
23 Juli 2024
21 Juli 2024
19 Juli 2024
16 Juli 2024
11 Juli 2024
7 Juli 2024
Bedienungsanleitung Sander
- Sander Makita
- Sander Bosch
- Sander Flex
- Sander Parkside
- Sander Vonroc
- Sander AEG
- Sander Arendo
- Sander Gastroback
- Sander Black And Decker
- Sander Cocraft
- Sander Ryobi
- Sander Skil
- Sander Topcraft
- Sander Trotec
- Sander Hilti
- Sander Bort
- Sander DeWalt
- Sander Einhell
- Sander Elu
- Sander Festool
- Sander Mafell
- Sander Maktec
- Sander Worx
- Sander Tacklife
- Sander Hikoki
- Sander Hitachi
- Sander Hyundai
- Sander Hazet
- Sander Kinzo
- Sander Kress
- Sander Max
- Sander Metabo
- Sander Stanley
- Sander Güde
- Sander Power Craft
- Sander Scheppach
- Sander Probuilder
- Sander Workzone
- Sander Biltema
- Sander Meec Tools
- Sander Dremel
- Sander Fieldmann
- Sander King Craft
- Sander Proxxon
- Sander Westfalia
- Sander Dedra
- Sander DURO
- Sander Far Tools
- Sander Silverline
- Sander Holzmann
- Sander Stomer
- Sander Batavia
- Sander Matrix
- Sander Bavaria
- Sander Brüder Mannesmann
- Sander Milwaukee
- Sander Toolcraft
- Sander Fein
- Sander Craftsman
- Sander Powerplus
- Sander Rupes
- Sander Alpha Tools
- Sander Toledo
- Sander Ozito
- Sander Ridgid
- Sander Porter-Cable
- Sander VARO
- Sander Duro Pro
- Sander Gamma
- Sander Global
- Sander Protool
- Sander Toolson
- Sander Wagner SprayTech
- Sander Meister Craft
- Sander Truper
- Sander RIKON
- Sander Einhell Bavaria
- Sander Tryton
- Sander FIXIT
- Sander Ribimex
- Sander Black Decker
- Sander Pevec
- Sander Handwerk
- Sander TAURUS Titanium
- Sander Stalco
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
8 Oktober 2024
7 Oktober 2024
5 Oktober 2024
5 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024
1 Oktober 2024