Felisatti RF55 Bedienungsanleitung
Felisatti
Fräsmaschine
RF55
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Felisatti RF55 (28 Seiten) in der Kategorie Fräsmaschine. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/28
TECHNICAL DATA
Milling machine RF55/1000E
A
bsorbed powe
r
W 1000
No load speed rpm 20000-27000
of milling cutter attachment mm 8
Lengthwise travel mm 0-55
maximum of milling cutter mm 36
Machine weight (without accessories) kg 3.75
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILUSTRATIONS
DESCRIPTION (See figures)
A Start-up switch (Fig.1)
B Spindle lock of shaft (Fig.1)
D Clip fixing nut (Fig.1)
E Depth stop (Fig.1)
F Stepped stop (Fig.1)
G Locking wing nut (Fig.1)
H Fixing lever (Fig.1)
I Side stop (Fig.1 and Fig.2)
J Transparent frontal protection (Fig.1 and Fig.2)
K Dust suction adapter (Fig.1 and Fig.3)
L Speed adjustment (Fig.1)
M Depth adjustment scale (Fig.1)
O Grips (Fig.1)
P Base plate (Fig.1)
Q Sliding plate (Fig.1)
R Wing screw for dust suction adapter (Fig.1 and Fig.3)
S Strip stop (Fig.2)
T Parallel stop fine adjustment (Fig.1 and Fig.2)
V Wing screw (Fig.1, Fig.2 and Fig.3)
EQUIPMENT
- Side stop
- Clip 8 mm
- Fixed spanner 17 mm
- Transparent guard
- Dust suction adapter
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
See “Safety Instructions” enclosed manual, supplied
together with this instruction manual.
WARNING! The dust produced when milling asbestos
and/or silica stone materials is dangerous to health.
Follow the insurance company’s safety instructions
regarding the responsibility of employees.
For your personal safety, always connect the machine
to a mains supply by a differential and thermal cut-out
switch, in accordance with regulations on low-voltage
wiring sitemaps.
Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
Always unplug the machine before doing any work on it.
Always stop the machine by switching it off, not by
unplugging it.
WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre. Only plug the machine in when it
is switched off.
Always keep the lead out of the machine’s working
area.
Only plug the machine in when it is switched off.
Do not allow the machine to get wet, nor should it be
used in wet environments.
When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
Check for correct piece fixing before commencing any
operation.
Only milling heads with acceptable revolutions that are
at least the same as the maximum off-load revolutions
of the machine should be used.
The milling head shaft diameter should match the
inside diameter of the tool-holder (locking clip).
It should be ensured that the milling head is firmly held
in place before the machine is operated.
The clip-carrier shaft support lever must only be oper-
ated when the machine is stopped.
The milling head should only be brought into contact
with the work-piece after it has been switched on.
The machine must be firmly held by the grips. Other-
wise the recoil produced could cause the machine to
work imprecisely or even dangerously.
Hold the machine firmly in both hands and in a stable
position.
The milling machine must never be used on metal
objects, such as nails and screws.
Hand must be kept clear of the milling machine while it
is operating.
The cutting depth must never be adjusted with the
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
The operator should remain alert and keep the milling
head apart from all objects during operation.
When the milling operation has been completed,
locking lever should be operated so that the machine
returns to its upper starting position.
Produktspezifikationen
| Marke: | Felisatti |
| Kategorie: | Fräsmaschine |
| Modell: | RF55 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Felisatti RF55 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Fräsmaschine Felisatti
14 Mai 2023
14 Mai 2023
Bedienungsanleitung Fräsmaschine
- Fräsmaschine Makita
- Fräsmaschine Bosch
- Fräsmaschine Flex
- Fräsmaschine Parkside
- Fräsmaschine Vonroc
- Fräsmaschine Black And Decker
- Fräsmaschine FERM
- Fräsmaschine Skil
- Fräsmaschine Topcraft
- Fräsmaschine Alpina
- Fräsmaschine Carat
- Fräsmaschine Eibenstock
- Fräsmaschine DeWalt
- Fräsmaschine Einhell
- Fräsmaschine Festool
- Fräsmaschine Mafell
- Fräsmaschine Maktec
- Fräsmaschine Triton
- Fräsmaschine Worx
- Fräsmaschine Hitachi
- Fräsmaschine Fuxtec
- Fräsmaschine Kinzo
- Fräsmaschine Güde
- Fräsmaschine Power Craft
- Fräsmaschine Meec Tools
- Fräsmaschine Westfalia
- Fräsmaschine DURO
- Fräsmaschine Holzmann
- Fräsmaschine Stomer
- Fräsmaschine Yato
- Fräsmaschine Brüder Mannesmann
- Fräsmaschine AL-KO
- Fräsmaschine Gardena
- Fräsmaschine Powerplus
- Fräsmaschine Rupes
- Fräsmaschine Toledo
- Fräsmaschine Ozito
- Fräsmaschine Texas
- Fräsmaschine Gamma
- Fräsmaschine Grizzly
- Fräsmaschine Protool
- Fräsmaschine Truper
- Fräsmaschine Trend
- Fräsmaschine CMT Orange Tools
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
15 Oktober 2024
4 Oktober 2024
20 September 2024
9 September 2024
6 September 2024
6 September 2024
6 September 2024
4 September 2024
4 September 2024