Extron P/2 DA2xi Bedienungsanleitung

Extron Empfänger P/2 DA2xi

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extron P/2 DA2xi (5 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/5

P/2 DA2xi • User Guide

The P/2 DA2xi is a high performance one input, two output distribution amplier that

accepts video input from a VGA-QXGA compatible PC and distributes that signal to

separately buffered outputs. The output can be extended with Extron MHR cables

up to 250 feet in length (XGA resolution signal).

The P/2 DA2xi routes all video ID bits to its local monitor output to allow for automatic

resolution selection by DDC1 and DDC2 (plug and play cards and projector).

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the

FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics,

see the “Extron Safety and Regulatory Compliance Guide” on the Extron website.

Specifications Availability

Product specications are available on the Extron website, www.extron.com.

Features

• Power LED — useful in system troubleshooting

• Impedance DIP switches — for solving laptop compatibility problems and reection problems due to long cable runs

• Bandwidth — 300 MHz (-3 dB) RGB video bandwidth maintains signal integrity

• ID bits pass-through — routes ID bits to the local monitor output to allow automatic scan rate selection by DDC

Mounting the P/2 DA2xi

Attention:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

The 1-inch high, quarter rack width P/2 DA2xi can be placed on a tabletop, mounted on a rack shelf, mounted under a desk or

tabletop, or mounted on a projector bracket.

Figure 1. Tabletop Placement

Attach the four included rubber feet to the bottom of the distribution amplier and place it in any convenient location.

P/2 DA2xi • User Guide (Continued)

Optional Mounting

NOTE: Accessory part numbers are available on the Extron website, www.extron.com.

The P2 DA2xi can be mounted using the following mounting kits:

• RSU 126 6” deep universal rack shelf kit

• RSB 126 6” deep basic rack shelf

• RSU 129 1U universal rack shelf kit

• RSB 129 1U basic rack shelf

• MBU 125 1U under-desk mounting kit

• MBD 129 1U through-desk mounting kit

The unit can be mounted in the front or the rear of the rack, as shown in the following illustration.

1. Remove the feet from the bottom of the P/2 DA2xi, if they

Use 2 mounting holes on

opposite corners.

(2) 4-40 x 3/16"

Screws

1U Universal Rack Shelf

are installed.

2. Mount the unit using two 4-40 x 3/16 inch screws in

opposite (diagonal) corners to secure the P/2 DA2xi

to the shelf.

3. Install false faceplates or other units to the rack shelf.

Under-furniture Mounting

The P/2 DA2xi can be mounted under a table or other horizontal surface using an optional Extron MBU 125 under-desk mounting

kit. Mount the unit under a desk or table, as follows:

1. Secure the under-desk mounting brackets to the distribution amplier with

the four machine screws provided in the mounting kit.

2. Hold the unit with attached brackets against the underside of the desk or

other furniture. Mark the location of holes for screws on the desk.

3. Drill 1/4 inch (6.4 mm) deep, 3/32 inch (2 mm) diameter pilot holes in the

table or desk at the marked screw locations from the underside or inside

(the concealed side) of the furniture, where the distribution amplier will

be located.

4. Insert the four wood screws into the pilot holes. Fasten each screw into

the installation surface until just less than 1/4 inch of the screw head

protrudes.

5. Align the installed screws with the slots in the mounting brackets, and

place the unit against the surface, with the screws through the bracket

slots.

6. Slide the unit slightly forward or back, then tighten all four screws to fasten

it in place.

P/2 DA2xi • User Guide (Continued)

Through-furniture Mounting

The distribution amplier can be mounted through a desk or other furniture using an optional Extron MBD 129 through-desk

mounting kit. Mount the P/2 DA2xi through a desk or table, as follows:

1. Loosely attach the mounting brackets to the unit using the four

machine screws and washers supplied with the mounting kit.

2. Hold the distribution amplier against the inside of the surface

through which it will be mounted. Mark the four screw holes on

the inside of the surface to which you are mounting the device.

3. Drill four pilot holes, each 3/32 inch in diameter by 1/4 inch deep,

where you made marks.

4. Using the four wood screws provided, secure the brackets to the

mounting surface.

5. Slide the unit up and down in the mounting brackets until the face

of the unit is at the desired height. Tighten the screws that secure

the bracket in place.

If the screws are inaccessible to a screwdriver:

a. Mark the location of the brackets relative to the screws.

b. Remove the P/2 DA2xi from inside the furniture.

c. Tighten the screws.

d. Replace the unit inside the surface (step 4).

Projector Mounting

The PMK 350 Low Prole Projector Mount Kit is an above-projector mounting kit that attaches to a 1 inch to 2 inches diameter

projector mounting pole. It can hold more than one device, in a variety of sizes. The PMK 350 is available in black or white.

Follow these steps to mount the P/2 DA2xi on the PMK 350 bracket as follows:

1. Remove the front and back panels from the

Extron

PMK 350

Multi-product Projector

Mounting Kit

Extron

P/2 DA2xi

Cover Sheet

Front Plate

Rear Plate

U-bolt

PMK 350, using an Extron Tweeker or other

small Philips screwdriver. (Retain the screws

to reattach the plates when you are nished.)

2. Remove any rubber feet from the bottom of

the P/2 DA2xi.

3. Secure the P/2 DA2xi to one side of the

mounting bracket, using two of the supplied

4-40 x 3/16 inch screws in opposite (diagonal)

corners.

4. Using the two included tie wraps, strap the

P/2 DA2xi power supply to the PMK 350 bracket.

5. Place the bracket around the projector ceiling

mounting pole as shown in the previous illustration.

6. Place the rubberized contoured base against

the pole and opposite the back plate. The pole

should t snugly into the depression in the center

of the contoured base.

7. Align the two slotted holes in the bottom of the L-shaped bracket with the two slotted holes in the base of the PMK 350, on

either side of the opening for the pole. Attach the L-bracket to the base by inserting two provided 6-32 x 5/16 inch screws

through the aligned slots.

8. Insert the two legs of the provided square U-bolt through the following parts in the order they are listed below:

• The slotted holes on the back side of the bracket mount plate

• The round holes in the rubberized contour base

• The round holes in the L-shaped bracket

For a typical (1.5 inches to 2.0 inches diameter) pole — You can use the supplied square U-bolt, which ts a typical

ceiling pole.

For a smaller pole — Locally obtain a square U-bolt that ts your ceiling pole. The slotted holes on the bracket can

accommodate a square U-bolt for pole sizes from 1.0 inch to 2.0 inches in diameter.

Produktspezifikationen

Marke:	Extron
Kategorie:	Empfänger
Modell:	P/2 DA2xi
Breite:	109 mm
Tiefe:	76 mm
Gewicht:	300 g
Produktfarbe:	Grey, White
Höhe:	25 mm
AC Eingangsfrequenz:	50 - 60 Hz
Verpackungsbreite:	222 mm
Verpackungstiefe:	313 mm
Verpackungshöhe:	64 mm
Paketgewicht:	1130 g
Eingangsstrom:	1 A
Bandbreite:	350 MHz
VGA (D-Sub)-Ausgangsanschlüsse:	2
VGA (D-Sub)-Eingangsanschlüsse:	1
Verstärkung:	0.7 dB