Extron IN1808 Bedienungsanleitung

Extron Nicht kategorisiert IN1808

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extron IN1808 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/6
1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
IN1808 Series • Setup Guide
The Extron IN1808 Series are eight-input seamless scaling presentation switchers that support signal resolutions up to
4K @ 60 Hz at 4:4:4. They feature DisplayPort, HDMI, and DTP2 inputs, HDMI output and a mirrored Extron DTP2 output
extension to send video, audio, and control signals up to 330 feet (100 meters) over a shielded CATx cable. The IN1808 IPCP SA
and IN1808 IPCP MA 70 models each have a built-in Extron IPCP Pro 355M IP Link Pro Control Processor, and an integrated
100 watt class D power amplier. The IN1808 Series delivers high image quality, fast and reliable switching, Extron ProDSP audio
processing, seamless video transition effects, logo keying, and HDMI loop out. The scalers can be controlled and congured over
Ethernet, RS-232, or USB.
This guide provides instructions for an experienced user to set up and congure the IN1808 (base model), IN1808 IPCP SA,
and IN1808 IPCP MA 70 scalers. It covers how to perform basic operations using the front panel controls and selected Simple
Instruction Set (SIS™) commands.
NOTES:
• For full installation, configuration, menus, connector wiring, and operation details, see the IN1806 and IN1808
Series User Guide at www.extron.com. For installation, configuration, and operation details of the embedded
IPCP Pro 355M, see the .IPCP Pro Series User Guide
• The IN1808 Series products can also be configured via the Extron Product Configuration Software (PCS), available at
www.extron.com. For information on using PCS, see the IN1806 and IN1808 Series Help File.
Installation
IN1808 Series Rear Panel Connectors
Figure 1 shows the rear panel of the IN1808 IPCP SA rear panel. The IN1808 IPCP MA 70 rear panel is the same except that
the embedded amplier is mono while the SA model amplier is stereo. The IN1808 base model rear panel does not have an
embedded IPCP Pro 355M module (see gure 1, P) or amplier module (N).
2x25W(8Ω)/2x50W(4Ω)
L R
CLASS 2 WIRING
AMPLIFIED OUTPUT
OUTPUTS (DTP/XT P/HDBT) AUDIO NPUTS OUTPUTS
HDMI/CEC
OVER TP
1A 1B
SIG LINK
OUT T x Rx
IR
G
1 2
3 4
+48V
+48V
1
2
MIC/LINE
L R
AUX
3 4
INPUTS (DTP2/XTP)
LOOP OUT
31
2
5
4 6 7
S IG LINK
IN
8
S IG LINK
IN
REMOTE
T x Rx
RS-232
G
RESET
100-240V~1.5A MAX
50-60 Hz
IN1808 IPCP SA
LAN
AV LAN 2 AV LAN 3
AV LAN 1
T x Rx
RT S CT S
G
T x Rx G T x Rx G
R
1 2 3 4 G
DIGI L I/OCOM 3COM 2COM 1 TA
S SG G
11 22 C 3 4 C +S G-S+V
PWR OUT = 6W
RRRRRRRRRRRRRRRRRRRRRRR
IR/SERIAL eBUSREL SAY
A C HB
O
E F G J KL
NQ P
D
M
I
Figure 1. Rear Panel Connectors, IN1808 IPCP SA
A
AC power connector
B
DisplayPort input connector (input 1)
C
HDMI (with CEC) loop out connector
D
DTP2/XTP input connectors (inputs 7
and 8)
E
HDMI (with CEC) output connector (1A)
F
DTP2/XTP/HDBaseT (with CEC) output
connector (1B)
G
Over TP IR pass-through connector
H Analog line audio inputs 3 and 4
I Analog mic/line audio inputs 1
and 2 and adjacent phantom
power LEDs
J Analog line audio outputs 1
through 4
K Remote RS-232 port
L Reset LED
M Reset button
N Amplified audio output (IPCP models
only)
o Aux mono or stereo analog line
audio input connector
P IPCP Pro 355M Control Processor
(IPCP models only)
Q HDMI inputs 2 through 6
R LAN connector (IN1808 base model
only, see the note and illustration
below)
NOTE: The IN1808 base model has a LAN connector to the left of the Remote RS-232 connector
(see R in the illustration at right) instead of the AV LAN ports on the IPCP Pro 355M control
processor.
Tx Rx
RS-232
G
RESET
1 2
3 4
LAN
OUTPUTS REMOTE
Tx Rx
RS-232
G
RESET
1 2
3 4
LAN
R
2
IN1808 • Setup Guide (Continued)
Mounting and Cabling
Step 1 Mount the device—
a. Turn off or disconnect all equipment power sources.
b. Mount the IN1808 to a rack using the pre-installed side mounting brackets, or remove the brackets and use an optional
19-inch rack under-desk mounting kit (see the mounting instructions provided with the kit, available at www.extron.com).
The IN1808 base model has a 1U high, full rack wide enclosure. The IN1808 IPCP models have 2U, full rack enclosures.
Step 2 Connect inputs—
Make the following input connections as needed:
• Connect a DP source to the Input 1 DisplayPort connector (see figure 1, B, on the previous page).
• Connect HDMI or DVI (with an appropriate adapter) sources to HDMI input connectors 2 through 6 (Q).
• Connect DTP transmitters to the DTP2/XTP RJ-45 input connectors 7 and 8 (
D). These connectors allow for remote
powering of DTP transmitters. You can configure the TP inputs for XTP mode via SIS commands, the on-screen
display (OSD), or PCS (see the ). For cable wiring and recommendations, see IN1808 Series Help File Twisted Pair
Recommendations for DTP, XTP, and HDBaseT Communication on the next page.
• Connect analog audio sources to:
• The 5-pole captive screw line audio input connectors 3 and 4 (H) and the Aux connector (O) for balanced or
unbalanced stereo audio. The Aux Line input is shared and can be associated with one or more video inputs.
• Connect balanced or unbalanced mic or line level inputs to 3-pole Mic/Line captive screw connectors 1 and 2 (I).
These inputs support optional +48 VDC phantom power, which is indicated by the LEDs at the left of the connectors.
Step 3 Connect outputs—
Make the following output connections as needed:
• Connect an HDMI, or DVI with an appropriate adapter, display to HDMI/CEC output connector 1A (E).
• Connect a DTP/XTP matrix switcher/HDBaseT compatible receiver to output connector 1B (F). For cable wiring and
recommendations, see Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication.
• To pass infrared data, connect a control device to the 3-pole IR Over DTP captive screw connector (see IR Over TP Wiring
on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT endpoint via Ethernet (see the IN1808
Series User Guide for more information).
• Connect balanced or unbalanced analog audio output devices to one or both 5-pole captive screw output connector pairs
1 and 2 or 3 and 4 (J). See on the next page for more information. Audio Wiring
• For IPCP models, connect speakers to the amplifier module via the 5 mm 4-pole stereo (IN1808 IPCP SA) or 2-pole mono
(IN1808 IPCP MA 70) Amplified Output connector (N).
Step 4 Connect control devices—
• To control the base model through Ethernet, connect a LAN or WAN to the LAN connector (
R). To wire the RJ-45 connector
to the cable, see Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication.
For the IPCP models, connect a LAN or WAN to any of the AV LAN connectors on the IPCP Pro control processor (P). The
default IP address of the scaler is 192.168.254.254. The default subnet mask is 255.255.255.0. The default gateway address
is 0.0.0.0.
• For serial RS-232 control, connect a host device to the 3-pole captive screw connector (K). The default baud rate is 9600.
• For control through USB, connect a host device to the front panel USB mini-B port (see figure 2, H on page 4).
Step 5 Set up the IPCP Pro 355M control processor (IPCP models only)—
The Extron IPCP Pro 355M control processor (see , figure 1 P) provides monitoring and control of a variety of external devices,
such as projectors and lights. See the , available at IPCP Pro Series Setup Guide www.extron.com, for installation details.
Step 6 Connect power—
Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (A).
3
Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication
Extron recommends using the following practices to achieve full transmission distances
and reduce transmission errors:
• Use Extron XTP/DTP 24 SF/UTP cable for the best performance. At a minimum, Extron
recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth of
400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at
right).
• Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
ATTENTION:
• Do not connect these connectors to a telecommunications or computer data
network.
• Ne connectez pas ces ports à des données informatiques ou à un réseau de
télécommunications ou de données informatiques.
• DTP remote power is intended for indoor use only. No part of the network that
uses DTP remote power should be routed outdoors.
• L’alimentation DTP à distance est destiné à une utilisation en intérieur
seulement. Aucune partie du réseau qui utilise l’alimentation DTP à distance ne
peut être routée en extérieur.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
Audio Wiring
Wire the audio input and output connectors as shown at right. Use
the supplied tie wrap to strap the audio cable to the extended tail
of the connector. This does not apply to the amplied audio output
connector on the SA and MA models.
ATTENTION:
• For unbalanced outputs, do not connect wires to the
“-” poles (see the illustration at right).
• Pour les sorties asymétriques, ne connectez pas de
câbles aux pôles «-» (voir l’illustration de droite).
NOTE: The length of exposed wires is critical. The ideal length
is 3/16 inch (5 mm).
IR Over TP Wiring
To transmit and receive IR signals, connect a control device to the
three-pole Over TP IR connector (G, Tx, and Rx).
NOTE: RS-232 data can be inserted via Ethernet only (see the
IN1806 and for details).IN1808 Series User Guide
TIA/EIA-T568B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
1 2 3 4 5 6 7 8
RJ-45
Connector
Insert istedTw
Pair Wires
Pins:
Balanced Audio Output
Tip
Ring
Tip
Ring
Slee
ves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Slee sve
L R
L R
Unbalanced Audio InputBalanced Audio Input
Tip
Ring
Tip
Ring
Slee sve
Tip
Sleeve
Sleeve
Tip
L R
L R
Do not tin the wires!
A
udio Inputs and Outputs 1 – 4 and xAu
Mic/Line Inputs 1 and
2
Balanced Audio Input
Tip
Slee
ve
Ring
Unbalanced Audio Input
Tip
Sleeve

Produktspezifikationen

Marke: Extron
Kategorie: Nicht kategorisiert
Modell: IN1808

Brauchst du Hilfe?

Wenn Sie Hilfe mit Extron IN1808 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Extron

Extron

Extron DTP T UWP 4K 232 D Bedienungsanleitung

1 Oktober 2024
Extron

Extron FOX Matrix 7200 Bedienungsanleitung

24 September 2024
Extron

Extron EWB 210 Series Bedienungsanleitung

24 September 2024
Extron

Extron EDID 101D Bedienungsanleitung

24 September 2024
Extron

Extron FMR 206 Bedienungsanleitung

24 September 2024
Extron

Extron EWB Series Bedienungsanleitung

24 September 2024
Extron

Extron IR Sensor Bedienungsanleitung

24 September 2024
Extron

Extron AVEdge 100 Bedienungsanleitung

12 September 2024
Extron

Extron MLM 100 AAP Bedienungsanleitung

12 September 2024
Extron

Extron MAAP 100 Bedienungsanleitung

12 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024