Extron DTP HDMI 4K 230 RX Bedienungsanleitung

Extron Empfänger DTP HDMI 4K 230 RX

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extron DTP HDMI 4K 230 RX (2 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

DTP HDMI 230 Tx Rear Panel DTP HDMI 230 Rx Rear Panel

Front nelPa

DTP HDMI 230 Rx

OVER DTP

RS-232 IR

Tx Rx Tx RxG

L R

POWER

12V

0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

AUDIO

INPUTS OVER DTP

RS-232 IR

Tx Rx Tx RxG

POWER

12V

0.7A MAX

SIG LINK

DTP OUT

3 6

7 71 54 42

DTP HDMI 230 • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the

Extron DTP HDMI 230 digital video extender. The DTP HDMI 230 transmitter and receiver pair can

extend an HDCP-compliant HDMI signal up to 230 feet (70 m).

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.

Step 2 — Connections

a — Connect an HDMI HDMI Input connector (Tx)

cable between this port and the HDMI output port of

the digital video source.

NOTE: See the “ “on the back of this guide for to

LockIt™ Lacing Brackets

securely fasten the input HDMI connector to the transmitter.

b — Connect an unbalanced stereo audio source to this 3.5 mm mini Audio input (Tx)

stereo jack for an analog audio input.

c — To pass serial or infrared data or control signals, such as RS-232 and IR connectors

serial control of a projector, connect the master device to the transmitter and the slave

device to the receiver via the RS-232 and IR captive screw connectors on both units.

d — Connect transmitter DTP Out to receiver DTP In. DTP RJ-45 connectors

Extron recommends that you terminate both cable ends in accordance with the

following speciﬁcations, at a minimum:

z zTIA/EIA T 568 B CAT 6A, shielded

z24 AWG, solid conductor

ATTENTION: Do not connect these devices to a computer data or telecommunications

network.

Signal LED — Lights when the unit is receiving a TMDS clock signal on the HDMI input (transmitter) or

any valid signal on the DTP In connector (receiver).

Link LED — Lights when a valid link is established between the units on the DTP cable.

e — Connect a display with an HDMI input for display of the HDMI Output connector (Rx)

transmitted direct digital image.

NOTE: See the “ “on the back of this guide for to LockIt™ Lacing Brackets

securely fasten the output HDMI connector to the receiver.

f — Connect a balanced or unbalanced stereo or mono audio Audio Output connector (Rx)

device to the receiver via the Audio captive screw connector. See the drawing below.

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

Ring

Tip

Ring

Slee sve

Tip

No Ground Here

Tip

Slee sve

L R

ATTENTION: .Connect the sleeves to the ground contact. connect the sleeves to the negative (-) contactsDO NOT

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

TP Wires

1 8234567

Pins:

Ground

Receive pin on connected unit

ansmit pin on connected unit

Connected RS-232

and IR Device Pins

Tx/Rx

Pins

Receive pin on connected unit

ansmit pin on connected unit

RS-232 IR

Tx Rx Tx RxG

L R

AUDIO

OUTPUTS

AUDIO

INPUTS

g — Connect an IEC power cord between the included 12 VDC Power connector

power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to

either unit as shown at right. Use the included tie-wrap to strap the cord to the

captive screw connector.

NOTE: Only one power supply is required. A single power supply

connected to either unit in the pair powers both units. A power

supply is included with each transmitter.

Operation

After all devices are powered up, the system is fully operational. See the deﬁnitions

Rear Panel

ear

ane

Front Panel

ront

ane

POWER

12V

0.6 A MAX

of the power indications (shown at right), below:

a —Power LED (front panel)

Amber — The unit is receiving power, either locally or remotely (on the DTP cable).

Green — The unit is powered on and is receiving an active HDMI signal, either on

the HDMI input if a transmitter, or transmitted on the DTP cable if a receiver.

b —Power LED (rear panel)

Amber — The unit is receiving power remotely (on the DTP cable).

Green — The unit is receiving power locally.

If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the

Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.

LockIt™ Lacing Brackets

Use an included LockIt Lacing Bracket to securely fasten an HDMI cable to each device as follows.

1. Plug the HDMI cable into the panel connection.

2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt

lacing bracket to be placed over it. The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the

screw to secure the bracket.

ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield

it fastens to is very thin and can easily be stripped.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket

as shown.

5. While holding the connector securely against the lacing bracket, use pliers or similar tools to

tighten the tie wrap, then remove any excess length.

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) Max.

SECTION A–A

68-2244-50

Rev A

07 12

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

(Inside Asia Only)

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+4000.398766

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

Inside India Only

+91.80.3055.3777

+91.80.3055.3737 FAX

DTP HDMI 230 • Setup Guide (Continued)

Produktspezifikationen

Marke:	Extron
Kategorie:	Empfänger
Modell:	DTP HDMI 4K 230 RX
WLAN:	Nein
Bluetooth:	Nein
Breite:	109 mm
Tiefe:	152 mm
Gewicht:	800 g
Produktfarbe:	Black, Stainless steel
Übertragungstechnik:	Kabelgebunden
Höhe:	25 mm
AC Eingangsspannung:	100-240 V
AC Eingangsfrequenz:	50 - 60 Hz
Betriebstemperatur:	-40 - 70 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Paketgewicht:	2000 g
Fernbedienung enthalten:	Nein
Zertifizierung:	CE, c-UL, UL\nCE, C-tick, FCC Class A, ICES, VCCI, KCC
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Temperaturbereich bei Lagerung:	0 - 50 °C
Luftfeuchtigkeit bei Lagerung:	10 - 90 %
Audio Kanäle:	- Kanäle
THD, totalklirren:	0.03 %
Unterstützte Grafik-Auflösungen:	2560 x 1600 (WQXGA),3840 x 2160,4096 x 2160
3D:	Nein
Rauschverhältnis (SNR):	90 dB
Frequenzbereich:	20 - 20000 Hz
Receiver Typus:	Stereo
Integrierter Kartenleser:	Nein
HDMI-Version:	1.4
Verpackungsabmessungen (BxTxH):	146 x 191 x 57 mm
Apple-Docking:	Nein
Ausgangsleistung pro Kanal (20-20KHz@8 Ohm):	- W
Stromeingang:	Ja
HDMI-In:	1
Farbtiefe:	8 Bit
Optisches Laufwerk enthalten:	Nein
AirPlay:	Nein
Display-Auflösung:	4096 x 2160 Pixel
Ethernet/LAN:	Ja