Eureka Solitaire SRS2 Bedienungsanleitung

Eureka Heizung Solitaire SRS2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Eureka Solitaire SRS2 (4 Seiten) in der Kategorie Heizung. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

• Smoke entering the room from the firebox when the door is open may be caused by

• Insufficient length of flue (Flue to be 4500mm minimum from underneath base of heater to underside of cowl)

– Increase height of flue.

• Flue Downdraught

– Consult dealer or increase height of flue.

• Creosote Build up in flue

– Remove cowl and clean flue as per cleaning instructions. Check moisture content of wood.

• Excessive ash build up

Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the

wood which is most convenient for you as long as it is dry. After a period of time you will get to know when to

empty your unit. Always leave 12mm of ash in the bottom of your heater. Bark will give you excessive ash. Try not to

burn it.

If you are burning wood that gives you charcoal, you may find that after running the heater say for 8 hours at

maximum burn rate, the charcoal builds up excessively. Overnight burn will reduce this charcoal back to a fine ash. If

you are not ready to shutdown for overnight burn when you next fuel the stove, load the stove with only one piece

of wood and lay it across the firebox on top of the charcoal. Open the air control wide open and you will find the

charcoal will burn down with the one piece of wood. Repeat the process until the ash level is significantly reduced.

GPN 207918

REV. D

Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding

Solitaire SRS2, Onyx, Diamond

& Emerald Mk3 Freestanding

Operation & Installation Instructions

Troubleshooting (Continued)

Solitaire SRS2 Freestanding shown

1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason) warrants the following components of its heaters against defects in workmanship

and/or materials for the following periods from the date of purchase:

(a) the firebox for ten years;

(b) the paint finish for a period of twelve months if the purchaser has followed the instructions provided by Gason in this Operation and Installation Instructions manual; and

(c) all other components for twelve months except the glass, fire brick lining or baffle plate if, in the opinion of Gason, these items have been damaged by impact.

2. This extended warranty does not apply:

(a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;

(b) if, in the opinion of Gason, the heater or any component has been subjected to abuse, misuse, alteration, modification or has not been installed, operated or maintained in

accordance with the instructions provided by Gason; or

3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason service

centre to arrange for an assessment.

4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:

(a) replace the heater;

(b) repair or replace specific components of the heater; or

5. Parts replaced under this warranty are warranted for the balance of their original warranty period.

6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this

warranty must pay all costs associated with:

(a) returning the heater; and

(b) the delivery or collection of any new or repaired heater.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for

compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and

the failure does not amount to a major failure.

Any benefits you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which

these warranties relate.

These warranties are given by:

A.F. Gason Pty Ltd

Blake Street

Ararat VIC 3322

Please contact us if you have any queries on:

Phone: 03 5352 2151;

or email us via the “Contact Us” section of our website: www.gason.com.au.

Eureka Heating reserves the right to modify or alter specifications, materials, etc. in the interest of product improvement.

WARRANTY

Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding

Troubleshooting

WARNING

NEVER OPERATE THE HEATER WITH THE DOOR LOOSE AND NOT AIR TIGHT.

OVERFIRING COULD RESULT IN DETRIMENTAL WEAR AND TEAR ON THE

FIREBOX.

• Noisy Fan

Turn the power off and remove the three pin plug from the power point. Remove the four screws that hold the front

fan access panel. Remove the panel. Disconnect the wiring loom via the plastic joiner. Unscrew the two nuts which

hold the fan in position and remove the fan. Clean any dust with a dry paint brush and vacuum the fan blades. Clean

around the motor. After completion place two or three drops of sewing machine oil on the shafts at the bearings.

Replace the fan in reverse to the removal.

• Fan not working

Check the power connection with another appliance. If the power point is O.K. assume the Fan or the Switch is

defective. Isolate the power as above. Check that the terminals on the loom and the switch are firmly connected. If the

fan then fails to function, remove the fan and switch by firstly removing the knob off the fan switch by pulling it away

from the heater. Undo the holding nut and pull the switch out. Disconnect the wiring from the power lead and remove

the fan and switch. Convey the same to the authorised Eureka Dealer from whom you purchased your unit for service.

Replace in the reverse order.

• Air Control Jamming

Remove air control cover plate by removing the four screws which hold it onto the face of the heater. There are two bolts

holding the air slide in place. Undo them and remove the air slide. Wipe any ash or dust that may have accumulated on

the back of the air slide or on the face of the heater. If any burrs have developed on the back of the air slide or on the

face of the heater, rub them off with fine wet and dry sand paper till you have a smooth surface and edges. Replace the

air slide and make sure the washers and spacers are on the bolts when you screw the bolts back into the face of the

heater. Do not apply any type of lubricant to the air slide whatsoever as this will attract dust and make the slide stick.

• No Overnight Burn

Remove the air slide as per air control jamming and check that the air slide is hard against the face of the heater. If it is

loose, tighten up the bolts holding the air slide to the face of the heater. Do not overtighten.

Check that the door rope has an even indentation from the sealing strip, which is on the face of the firebox. If it is uneven

and it appears as though air could leak through the seal, adjust the thickness of the door rope to suit. Stretch the rope to

make it thinner where the indentation is the heaviest and bunch up the excess where the indentation is smaller.

Check the four bolts that hold the glass retainer in position. If loose tighten. Do not overtighten.

The door may become loose through the door seal shrinking. To tighten the door, open the door and look at the inside of

the door catch. Undo the nut which is holding the latch plate. Remove the latch plate. Remove one thick washer and the

star washer. Refit the latch plate. The latch plate is concave to provide a lead in edge so that there is smooth connection

between the door latch and the catch. Make sure that the face of the latch that is curved outward is facing towards the

door.

Replace the nut. When closing the door you should now feel firm resistance when the latch comes into contact with the

catch.

Overfiring

Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding

WARNING

Read and follow these instructions carefully before installing and

using this appliance.

SAVE THESE INSTRUCTIONS

Paint curing and care

WARNING

• A flue fire with resulting damage may occur if this appliance is not installed,

operated and maintained as per this booklet.

• Never place combustible material such as wood, paper or furniture near the

appliance.

• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood,

flammable liquids or any substance containing salts or corrosives.

• This appliance must not be installed and operated in an area where kerosene,

petrol, paint thinner or other flammable liquid is used or stored.

• The flue system must be inspected and cleaned annually or sooner if required.

Failure to do so could result in an excessive build up of creosote which may

result in a flue fire which may damage the flue or cause damage to your

home.

• The surface of the appliance becomes hot during operation. Do not touch the

surface of this appliance. Keep children away from the appliance during

operation. Do not allow anyone to operate this appliance who is not familiar

with the instructions in this booklet.

WARNING

Your heater is coated with the best available heat resistant paint. Even though

the paint has been baked after application, it may require further temperature

curing. It may, if you overfire the heater on its first fire, discolour. For your first

two or three firings, never exceed medium air setting and always have the fan on

when above low burn. Do not wipe the heater while the paint is curing. After the

paint has cured the only maintenance required to maintain the heaters finish is to

wipe it with a soft cloth. Do not use any commercial cleaners or solvents on the

paint finish.

We are proud of the presentation of our products. If at any time you need to

freshen up the paint finish, your local dealer has touch up paint available for

purchase. You may even change the colour of your heater if you wish.

If you have any enquires, please contact the dealer from whom you purchased your heater:

PLEASE COMPLETE:

Dealer Name

Dealer Address

Phone

Please attach your original purchase dockets to this booklet for future reference.

Safety Warnings

Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding

Operating your Eureka (Continued)

Overnight burn

Approximately 30 minutes before turning the heater down to overnight burn it is recommended to load the heater with

fuel for the overnight burn. Leave the air control in the medium to high position. Let the heater run for about thirty

minutes. This will reduce the moisture content in the fuel before shut down. (This will help reduce the creosote formation

in the firebox and flue.) Set the air control to the setting you have found best for your requirements which is normally

about 8mm to the right of full shut down. Turn the fan off and retire. The aim when overnight burning is to have only a

few hot embers left in the bottom of the firebox in the morning. Not huge lumps of wood.

Cleaning your flue

Carefully remove baffle plate and put it to one side. Close the heater door. Obtain a flue brush (Solitaire SRS2 178mm,

Onyx/Diamond/Emerald Mk3 150mm) from your local Eureka Dealer and proceed up onto your roof. Remove the cowl.

Slowly push the flue brush down the chimney until it stops. Pull the brush back out and repeat the process. Each time you

do this you will notice that the brush will go further down the chimney till it reaches the bottom. The soot and creosote

will fall down the chimney and into the firebox. Clean residue from firebox. Replace the baffle plate. Make sure you do

the job well. The cleaner the flue the less chance there will be of the creosote sticking again. After you have replaced the

cowl, inspect the roof flashing for any damage that may have been incurred whilst you were cleaning the flue. Reseal the

seal on the roof with roof and gutter silicone if required.

The fan

It is recommended to run the fan while the heater is operating above low burn on low speed. For extended periods when

the heater is running above medium fire, high or boost is recommended. Boost is recommended for short bursts where a

quick temperature rise is desired in conjunction with a high fire setting. The fan should be cleaned on a regular basis.

(Refer Troubleshooting for fan removal and cleaning.)

WARNING

Leaving Door Open

As stated previously in relation to leaving door open 25mm to encourage the fire

to pick up at a faster rate. Your heater has been tested to ensure that no

structural damage can take place if the door is inadvertently left open. However

your paint finish can be damaged if the door is left open for a long period with a

full firebox of fuel with the fan off. Closely supervise your heater while the door is

left open.

Closing the Door

Always ensure that before you close your door there is no wood protruding

beyond the front of the firebox opening. Do not use the door glass as a ’battering

ram’ to push the wood back into the firebox. Damage to the glass by such

impact is not covered by your warranty.

The Door

Installation

WARNING

THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS

MANUAL AND THE FLUE MANUFACTURERS SPECIFICATIONS.

WE RECOMMEND THAT YOU USE A QUALIFIED INSTALLER TO CARRY OUT

THE INSTALLATION.

If you have any other enquiries, please contact the dealer from whom you

purchased your heater.

THIS APPLIANCE WEIGHS IN EXCESS OF 170 KILOGRAMS. EXTREME CARE

SHOULD BE TAKEN WHEN HANDLING THE APPLIANCE.

Clearances to combustibles & flue requirements

It is recommended that you either use the flue kit that was tested in test report numbers shown below, or an approved

Australian Standard flue kit, (that incorporates a decorative surround which is unperforated for 180 degrees of its

circumference) in conjunction with the original test report.

The Eureka Solitaire SRS2, Onyx, Diamond & Emerald Mk3 have been tested to the Australian Standard 2918:1990 Appendix B.

• SOLITAIRE SRS2: Report RF/95/091.

•

ONYX: Report HCU/98/005 . A

• DIAMOND: Report RF/95/097.

• EMERALD Mk3: Report HCU/96/116.

The Solitaire SRS2, Onyx, Diamond and Emerald Mk3 Freestanding heaters conform to the Australian Standard in the

following placement of the appliance in relation to combustible surfaces.

Rear Wall

(Solitaire SRS2) 50mm

(Onyx) 50mm

(Diamond) 25mm

(Emerald Mk 3) 125mm

(Solitaire SRS2) 50mm

(Onyx) 50mm

(Diamond) 25mm

(Emerald Mk 3) 125mm

Side Wall

Rear Wall

(Solitaire SRS2) 100mm

(Onyx) 100mm

(Diamond) 100mm

(Emerald Mk3) 150mm

(Solitaire SRS2) 350mm

(Onyx) 330mm

(Diamond) 300mm

(Emerald Mk3) 450mm

Side Wall

Floor Protector

Installation

SOLITAIRE SRS2:The Solitaire SRS2 conforms to A.S. 2918:1990 when placed in the above position on a minimum

hearth or floor protector of 1170 mm deep x 975mm wide x 7.5mm thickness. The floor protector should extend

400mm in front of the appliance base.

ONYX: The Onyx conforms to when placed in AS/NZS 2918:2018 the above position on a minimum hearth or floor

protector of 1020 mm deep x 1170 mm wide x 4 mm thickness. The floor protector should extend 300mm in front of

the appliance base.

DIAMOND:The Diamond conforms to A.S. 2918:1990 when placed in the above position on a minimum hearth or floor

protector of 1070mm deep x 910mm wide x 7.5mm thickness. The floor protector should extend 350mm in front of the

appliance base.

EMERALD MK3: The Emerald Mk3 conforms to when placed in the above position on a AS/NZS 2918:2018

minimum hearth or floor protector of 1070 mm deep x 900 mm wide x 4.5 mm thickness. The floor protector

should extend 300mm in front of the appliance base.

Hearth Requirements

Operation of the Fan

WARNING

If firebox failure is reported and it is found that the firebox has been abused

through improper use of the fan, Eureka reserve the right to disallow any

warranty claims in relation to firebox failure.

Produktspezifikationen

Marke:	Eureka
Kategorie:	Heizung
Modell:	Solitaire SRS2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Eureka Solitaire SRS2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Heizung Eureka

Eureka Stockade SRS5 Insert Bedienungsanleitung

22 August 2024

Eureka Opal SRS4 Insert Bedienungsanleitung

22 August 2024

Eureka Opal SRS3 Freestanding Bedienungsanleitung

11 August 2024

Eureka Jewel Freestanding Bedienungsanleitung

9 August 2024

Eureka Solitaire SRS2 Bedienungsanleitung

28 Juli 2024

Eureka Garnet SRS2 Freestanding Bedienungsanleitung

7 Januar 2024

Eureka Garnet SRS3 Insert Bedienungsanleitung

7 Dezember 2023

Eureka Pearl Insert Bedienungsanleitung

10 August 2023

Eureka Ruby Freestanding Bedienungsanleitung

31 Oktober 2022

Eureka Ruby Insert Bedienungsanleitung

29 Oktober 2022

Bedienungsanleitung Heizung

Neueste Bedienungsanleitung für -Kategorien-

Harvia Delta D29EE HDEE290400 Bedienungsanleitung

16 Oktober 2024

MSW -CTEH-15000 Bedienungsanleitung

16 Oktober 2024

Uniprodo UNI_HEATER_05 Bedienungsanleitung

16 Oktober 2024

Uniprodo UNI_HEATER_06 Bedienungsanleitung

16 Oktober 2024

MSW -TTEH-2000 Bedienungsanleitung

16 Oktober 2024

Uniprodo UNI_HEATER_04 Bedienungsanleitung

16 Oktober 2024

Uniprodo UNI_HEATER_07 Bedienungsanleitung

16 Oktober 2024

Jøtul F 361 Bedienungsanleitung

15 Oktober 2024

Adler AD 7752 Bedienungsanleitung

15 Oktober 2024

MSW -TTEH-3000 Bedienungsanleitung

15 Oktober 2024