Ernitec ELECTRA-S-24F Bedienungsanleitung

Ernitec Schalter ELECTRA-S-24F

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ernitec ELECTRA-S-24F (4 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

www.ernitec.com

Ernitec

Tempovej 41

2750 Ballerup

Denmark

Professional Surveillance Solutions

Electra

Manual

Electra S24F

www.ernitec.com

Ernitec

Tempovej 41

2750 Ballerup

Denmark

Manual Electra S24F V01270916

Introduction

Power- -over Ethernet (PoE) eliminates the need to run DC power to other devices on a single wired

LAN. Using Power- -Over Ethernet, installers only need to run a single CAT 5cable carries that both

data and power to each device. This allows flexibilliy greater in the location of the network

devices. And in many cases significantly decreases the installation costs.

There are two system components in the PSE (Power Sourcing Equipment) and the PD PoE –

(Powered Device). The IEEE 802.3af/at specification defines PSE as a device that inserts power

onto an Ethernet cable. The PSE may be located at the switch (Endspan configuration). Or it may

be a separate device (Poe Injector) located between the switch and the PD (Midspan

configuration). The PD is the natural termination of this link, receiving the power and the data

And it could be an IP camera or an IP phone or a WLAN Access Point that require power.

The current is transmitted over 2 of the 4 twisted pairs of wires in a Category 5, 6, 7 cable.-

Power- -over Ethernet follows the IEEE 802.3af/at specification and is completely compatible

with existing Ethernet switches and networked devices. Because the Power Sourcing Equipment

(PSE) tests whether a networked device is PoE-capable, power is never transmitted unless a

Powered Device is at the other end of the cable. It also continues to monitor the channel. If the

Powered Device does not draw a minimum current, because it has been unplugged or physically

turned off, the PSE shuts down the power to that port.

Optionally, the standard permits Powered Devices to signal th the PSEs exactly how much power

they need.

The PoE switch is a multi-port fast Ethernet switch that can be used to build high-performance

switched workgroup networks. This switch is a store- -and forward device that offers low latency for

high-speed networking. It also features a “store- -and forward” switching scheme that allows the

switch to auto-learn and store source addresses in a 8K-entry MAC address table. The switch is

targeted at workgroup, department or backbone computing environments.

www.ernitec.com

Ernitec

Tempovej 41

2750 Ballerup

Denmark

Manual Electra S24F V01270916

Hardware Description

The Front Panel:

The front panel constists of LED Indicationes, 24 x 10/100/1000M RJ45 ports plus

4 1000M x SFP Combo ports.

Figure 2. Front panel view of LED indications

Figure 2

LED

Status

Color

Description

Power

Green

The switch is supplied with suitable power

LINK/ACT

Green

The port is

connecting

Blinks

The port is

recieving or transmitting data

Off

The port is not

linked successfully with the device

PoE

Green

PD is

connected

No PD is

connected or the device does not need power

Figure 3

The Panel:Rear

The Real panel constists of AC outlet, power swtich and fuse.

Produktspezifikationen

Marke:	Ernitec
Kategorie:	Schalter
Modell:	ELECTRA-S-24F
Gewicht:	4500 g
Mitgelieferte Kabel:	AC
Produktfarbe:	Schwarz
AC Eingangsspannung:	100 - 240 V
AC Eingangsfrequenz:	50 - 60 Hz
DC input Spannung:	48 V
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	20 - 85 %
Netzstandard:	IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x
Zertifizierung:	FCC, CE
Vollduplex:	Ja
Power over Ethernet (PoE):	Ja
Betriebsanleitung:	Ja
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-10 - 70 °C
Switch-Typ:	Unmanaged
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	24
Basic Switching RJ-45 Ethernet Ports-Typ:	Gigabit Ethernet (10/100/1000)
10G-Unterstützung:	Nein
Kupfer Ethernet Verkabelungstechnologie:	10BASE-T, 100BASE-TX, 1000BASE-TX
MAC-Adressentabelle:	8000 Eintragungen
Routing-/Switching-Kapazität:	52 Gbit/s
Rack-Einbau:	Ja
Formfaktor:	1U
Anzahl Combo-SPF-Anschlüsse:	4
unterstütze Kabeltypen:	Cat5, Cat5e
Unterstützung Datenflusssteuerung:	Ja
Gesamtleistung Power over Ethernet (PoE):	500 W
Optischer Kabelverbinder:	SFP
Power over Ethernet (PoE) Leistung pro Anschluss:	30 W
Transmissionsentfernung (max):	20 km