Erica Synths Pico VCO Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Erica Synths Pico VCO (3 Seiten) in der Kategorie Klaviatur. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
FEATURESTECHNICAL SPECS
Thank you for purchasing Erica Synths Pico Series module!
With Pico Series we challenged ourselves – can we make ANY
superior functionality synth module 3HP wide and affordable?
Erica Pico VCO is great, deep sounding VCO with 32 selected
waves – classical, fattened with sub-oscillator, FM synth and
others. Typically you need several rather expensive modules
to generate similar sounds. Extra feature – flip a switch, and
you have a versatile LFO!
2 banks, each contains 16 waves
VCO/LFO mode
Voltage controlled wavesurfing
Wave morphing in LFO setting
VCO frequency range 30Hz – 5kHz
LFO frequency range 0,1Hz – 20Hz
Output amplitude 10Vptp
Power consumption +26mA, -4mA
Module width 3HP
Module depth 35mm
PICO
VCO
1V/OCT
W-CV
OUT
WAVE
TUNE
PICO
BANK2
BANK1
LFO
VCO
Use this knob to select one of
16 waves in each bank
Use this knob to tune the VCO to
desired initial frequency
Switch between banks of waves
Apply wavesurf CV here! You may
want to use Pico Attenuator or
Scaler to adjust wavesurfing span
This is the output, obviously
LED gives visual control of the output
signal in LFO mode
Select VCO or LFO mode. IN LFO MODE
WAVE MORPHING WILL BE AUTOMATICALLY
ACTIVATED. IT PROVIDES MORE
INTERESTING MODULATIONS IN TRANSITION
FROM ONE WAVE TO ANOTHER
Apply tune CV here! The VCO has
perfect 1V/oct tuning
Thank you for purchasing It comes 1V/oct calibrated, but PSUs on modular Erica Synths Pico VCO!
synths are so different, therefore, if needed, you can perform the calibration procedure specifically
for your modular setup. We have introduced two step calibration where you will need precise 5,000V
and 1,000V CV source (you can use midi-cv keyboard with 5 octaves range). To perform a calibration
procedure, follow these steps:
1) Disconnect your Pico VCO from the PSU.
2) Connect a patch cable to the CV source and make sure, you get 1,000V (exactly ONE VOLT) on the
output – you can play C1 on the midi-cv keyboard.
3) Turn both WAVE and TUNE knobs all way clockwise and flip both switches up (BANK1 and VCO
position). Then connect the VCO to the PSU on your modular! Output LED will light on.
4) Connect 1,000V patch cable to 1V/oct input of the Pico VCO!
5) Flip VCO/LFO switch down to LFO position to initiate the calibration step 1!
6) Now set the CV source to 5,000V (exactly volts) – you can play C5 on the midi-cv keyboard.five
7) Flip VCO/LFO switch up to VCO position to initiate the calibration step 2!
8) Output LED will blink once, and this means that you have successfully calibrated the VCO!
Water is lethal for most of the electric devices, unless they are made
waterproof. This Erica Synths module is NOT intended for use in a humid or
wet environment. No liquids or other conducting substances must get
into the module. Should this happen, the module should be disconnected
from mains power immediately, dried, examined and cleaned by
a qualified technician.
Do not expose the module to temperatures above +50° C or below -20° C.
If you have transported module in extreme low temperatures, leave it in
room temperature for an hour before plugging it in.
Transport the instrument carefully, never let it drop or fall over.
Warranty does not apply to modules with visual damages.
The module has to be shipped in the original packaging only. Any module
shipped to us for return, exchange and/or warranty repair has to be in
its original packaging. All other deliveries will be rejected
and returned to you. Make sure you keep the original packaging and
technical documentation.
This device complies to the EU guidelines and is manufactured ROHS
conforming without use of led, mercury, cadmium and chrome.
Nevertheless, this device is special waste and disposal in household
waste is not recommended.
Safety Instructions
You will find Erica Synths terms of warranty at www.ericasynths.lv.
Items for return, exchange and/or warranty repair have to be sent to:
Erica Synths
Andrejostas Str. 12
Riga
Latvia
LV-1045
User manual by Girts Ozolins@Erica Synths
Design by Ineta Briede@Carre Branding
Copying, distribution or any commercial use in any way is prohibited and needs the written
permission by Erica Synths. Specifications are subject to change without notice.
In case of any questions, feel free to contact us through www.ericasynths.lv or via e-mail
info@ericasynths.lv
Please follow the instructions for use of the Erica Synths module
below, ‘cause only this will guarantee proper operation of the module
and ensure warranty from Erica Synths.


Produktspezifikationen

Marke: Erica Synths
Kategorie: Klaviatur
Modell: Pico VCO

Brauchst du Hilfe?

Wenn Sie Hilfe mit Erica Synths Pico VCO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Klaviatur Erica Synths

Bedienungsanleitung Klaviatur

Neueste Bedienungsanleitung für -Kategorien-