Erica Synths Fusion VCO Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Erica Synths Fusion VCO (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
ERICA FUSION VCO
S
U
B
W
A
V
E
1
S
U
B
M
I
X
C
O
L
O
U
R
S
U
B
W
A
V
E
2
F
R
E
Q
U
E
N
C
Y
W
A
V
E
S
H
A
P
E
F
M
L
E
V
E
L
AUDIO IN 1V/OCTSUBMIX CV FM IN WAVE CV VCO OUT MIX OUT
-2-1
D
R
Y
/
W
E
T
FUSION VCO
THANK YOU FOR ORDERING
ERICA FUSION VCO MODULE!
The Erica Synths Fusion series modules
are designed combining vacuum
tubes and semiconductors therefore
they bring warm, powerful sound and
overdrive possibilities of vacuum tubes
into your modular system. Erica Fusion
series consist of range of modules
used in sound shaping circuitVCO,
Mixer, real Ringmodulator using
audio transformers and germanium
diode ring, VCF, VCA and Analogue
Delay/Chorus.
Conventional wisdom says that
vacuum tubes have nonlinear
characteristics, and therefore VCOs
based on vacuum tubes need special
tuning for each note.
Erica Synths Fusion VCO is special
kind of VCO it fuses good tuning
of digital VCO with warm, unique
sound of vacuum tubes that work in
suboscillator circuit. The module has to
vacuum tube based suboscillators: -1
and -2 octaves with plenty of mixing
opportunities for amazing sonic results.
If you wish to go really low frequencies
and have a sound that sets your
modular system apart from mass
this is exactly module, you need!
FEATURES:
3 basic waveforms with VC morphing
Good 1V/oct tuning
Vacuum tube based suboscillators -1 and -2 oct
Manually and CV controlled -1/-2 oct mixing
Adjustable suboscillator waveshape
Dry/Wet (VCO/suboscillators) mixing
Passive Lowpass filter for extreme subbass sound
Audio input
TECHNICAL SPECIFICATIONS:
Audio input level: up to 20V ptp .....................................................................................................
VCO range: C1 – C8 .........................................................................................................................
Max Output level: 10V ptp ...............................................................................................................
Panel width: ............................................................................................................................ 24HP
Module depth: 35mm .....................................................................................................................
Power supply: bipolar +-12V , eurorack standard and/or Erica Synths 6VAC PSU .................
Power consumption:
Tube heater PSU configuration: 60mA@+12V, 30mA@-12V, 300mA@6VAC ..........................
Eurorack PSU configuration: ..........................................................215mA@+12V, 185mA@-12V
(NB – start-up power consumption for few seconds is +-250mA)
Choose one of principal
waveforms of VCO
Set the VCO frequency
manually
Dry/Wet potentiometer
provides smooth mix between
pure VCO and pure tube
suboscillator sound
Use COLOUR potentiometer
to filter o higher harmonics
for extreme bass sound and
almost pure sine waveform
on the output. Full CCW
setting works best at really
low frequencies –
C1 and below
Adjust -1 octave
suboscillator waverofm from
more harmonic rich CW to
almost sine CCW
Adjust a mix between
-1 octave and -2 octaves
suboscillators
Connect 1V/oct
signal to control
VCO frequency
Apply CV to fade
between -1oct
and -2oct mix
Patch
FM CV
here
Apply wave
morphing CV here.
It will be added
to waveshape
potentiometer
setting
This is dry VCO
output, no
suboscillator is
added
This is master output. Get
that fat tube sound here
Adjust -2 octave
suboscillator waverofm from
more harmonic rich CW to
almost sine CCW
Use waveshape
potentiometer to
morph/adjust waveforms.
12 ‘o’clock setting gives
you waveform, selected
by the switch, and then
morphing is applied:
Sine morphs from
logarythmic wave to
overdriven sine
Triangle morphs from
ramp to sawtooth
Pule has adjustable PW
from 5% to 95%
Patch external VCO (simple
waveforms will work best)
to route it to suboscillator
circuit. Internal VCO will be
automatically disconnected
Adjust FM level with this
potentiometer
ERICA FUSION VCO
You can configure Erica Fusion modules for two PSU options.
1. When used with easy to install 6VAC Erica Tube heater PSU, Fusion modules have 60mA@+12V and 30mA@-12V power consumption from
eurorack PSU. Erica Fusion 6VAC PSU is designed to power up to 7 Erica Fusion modules, but your eurorack case needs 220VAC or 110VAC
routed inside the case (this is typical for most Doepfer cases and some other producers that use switching PSU). Latest Erica Synths cases
have Fusion tube heater connectors on integrated PSU boards. For Tube heater PSU connection refer next page.
2. When configured to work with standard +-12V eurorack PSU, power consumption is 215mA@+12V and 185mA@-12V, and you do not need to
install Fusion PSU. This configuration is the best for Make Noise and similar PSU systems that route only +12V in the case and use switching ICs
to generate +-12V.
For +-12V operation install 2 jumpers
on the Fusion PSU connector on the
left side as shown on the silkscreen.
For 6VAC operation from the Fusion
PSU, install jumpers on the right side.
Also, you can refer to small 12V or 6V
notes next to jumpers.
For +-12V operation install 2 jumpers
on the Fusion PSU connector on the
left side as shown on the silkscreen.
For 6VAC operation from the Fusion
PSU, install jumpers on the right side.
Also, you can refer to small 12V or 6V
notes next to jumpers.
ERICA FUSION VCO MODULE comes 1V/oct calibrated, but PSUs on modular synths are so dierent, therefore, if needed, you can perform the
calibration procedure specifically for your modular setup. We have introduced two step calibration where you will need precise 5,000V and 1,000V CV
source (you can use midi-cv keyboard with 5 octaves range). To perform a calibration procedure, follow these steps:
1. Disconnect your Fusion VCO from the PSU.
2. Connect a patch cable to the CV source and make sure, you get 1,000V (exactly ONE VOLT) on the output – you can play C1 on the midi-cv keyboard.
3. Turn both WAVE and TUNE knobs all way clockwise and flip both switches up (BANK1 and VCO position). Then connect the VCO to the PSU on your
modular! Output LED will light on.
4. Connect 1,000V patch cable to 1V/oct input of the Fusion VCO!
5. Flip VCO/LFO switch down to LFO position to initiate the calibration step 1!
6. Now set the CV source to 5,000V (exactly five volts) – you can play C5 on the midi-cv keyboard.
7. Flip VCO/LFO switch up to VCO position to initiate the calibration step 2!
8. Output LED will blink once, and this means that you have successfully calibrated the VCO!
ERICA FUSION VCO
It is advised that installation is performed by person, who has experience working with 220/110V voltages. Before installing the PSU, make
sure your modular system is turned o and disconnected from wall power socket.
Follow simple instructions below, and you will not go wrong with the installation!
Connect this lug to the
GND of your system!
Use ribbon cable supplied
with Fusion modules to
connect tube heaters here!
Use jumpers to configure the PSU
for the voltage in your country!
Use cables supplied with
Tube heater PSU to connect
the module to 220/110V socket
inside your modular case!


Produktspezifikationen

Marke: Erica Synths
Kategorie: Nicht kategorisiert
Modell: Fusion VCO

Brauchst du Hilfe?

Wenn Sie Hilfe mit Erica Synths Fusion VCO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Erica Synths

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-