Erica Synths Fusion Modulator Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Erica Synths Fusion Modulator (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
THANK YOU FOR ORDERING
ERICA FUSION MODULATOR!
The Erica Synths Fusion series
modules are designed combining
vacuum tubes and semiconductors
therefore they bring warm, powerful
sound and overdrive possibilities of
vacuum tubes into your modular
system. Erica Fusion series consist of
range of modules used in sound
shaping circuit two types of VCO,
Mixer, real Ringmodulator using audio
transformers and germanium diode
ring, VCF, VCA, Analogue Delay/-
Flanger, Palsma Drive and others. Also
Erica Fusion Systems are available.
Fusion Modulator is complex, all
analogue modulation source with lots
of distinct features. It consists of
several blocks two EMS Synthi
functionality inspired looping envelope
generators with simultaneous
unipolar (0V-10V) and bipolar
(-5V-+5V), VCA, Noise generator and
Sample&Hold. This makes Fusion
Modulator a versatile modulation
source for advanced modular setups,
especially drone music oriented ones.
Set lopping envelope generators to
high frequencies and have two sub
bass sound sources, use VCA to
control the amplitude of the envelope
signal, modulate the decay time by
random voltages from S&H circuit
and get ever evolving sonic
awesomeness!
D
E
C
A
Y
O
F
F
D
E
C
A
Y
O
F
F
A
T
T
A
C
K
O
N
A
T
T
A
C
K
O
N
S
&
H
L
E
V
E
L
S
&
H
R
A
T
E
E
G
L
V
L
/
V
C
A
O
F
F
S
E
T
GATE 1 GATE 2 S&H+BP BP2 EG OUT 2EOC BP 1 EG OUT 1
VCA OUT NOISE OUT CLK IN CV IN S&H OUTMANUAL VCA IN VCA CV
DEC CV2DEC CV1
FUSION MODULATOR
1
34
11
2
12
13
15
18
19
1617
14
5
6
7 88 910
Set the desired attack time!
This is very specific looping envelope
generator – you can adjust attack
and decay time like on regular
looping EGs, as well as ON time and
OFF time, which simulate gate on
and off. Please, refer to the
envelope shape diagram below!
Adjust the Decay time manually! The
Decay time is also CV controlled, and
the CV is added to the knob setting.
Adjust the OFF time! If you wish to
use the envelope generator with
external gates only, set the OFF knob
to rightmost position and the looping
will stop! The large LED gives visual
feedback on the envelope status
This is the Decay CV input. The CV
is added to the knob setting
This is the Manual Gate button, it
sets the ON stage of the envelope
high. When released, envelope will
continue looping, unless the loop is
off (OFF knob at 5PM). The manual
button has an effect on the left
envelope generator only
This is an external Gate input. It
works the same as manual button.
This is End Of Cycle output – it outputs
+5V signal when the envelope is in OFF
stage
This is bipolar (-5V - +5V) envelope
output, meaning, you can use the
envelope generator as the LFO
This is the unipolar (0- +10V) envelope
output
Most of controls on the right side
of the module are identical to the
left one
The module has built-in VCA for both
CV and audio processing. Use EG
LVL/VCA OFFSET knob to adjust VCA
CV offset, essentially VCA output
level!
Adjust the internal S&H clock rate! If
an external clock is connected, it
automatically disconnects the internal
one. The LED gives visual feedback on
the clock rate.
This is the S&H input CV attenuator. By
default it’s normaled to the internal
noise generator.
This is the white noise output. The
module has Zener diode based noise
generator that provides nice, full
spectrum white noise
This is the S&H random voltage output
This is the external CV input for S&H
circuit. The external CV automatically
disconnects the internal white noise
form the input.
This is the external S&H clock input!
Try patching the EOC signal here!
This is super-random CV output – a
sum of bipolar envelope generator
output and S&H output
This is the VCA input; it accepts both
audio and CV signals. The input is
normaled to the bipolar output of the
left envelope generator, so you can
use the EG LVL knob to control the LFO
(bipolar envelope generator output)
signal level manually and VCA CV input
to control the LFO level via CV
This is VCA CV input, it’s added to the
CV is added to the VCA offset knob
setting
This is the VCA output. If nothing is
patched into VCA IN, you will get the
LFO signal with adjustable amplitude
here.
1
7
14
15
16
17
18
19
20
21
22
8
9
10
11
12
13
2
3
4
5
6
20 21 22
FEATURES:
Full analogue design
Two lopping envelope generators with Attack, On, Decay and Off time control
CV control over Decay time
Simultaneous unipolar (0V-10V) and bipolar (-5V - +5V) envelope outputs
Manual trigger button
End of Cycle output
VCA with the offset control
Zener diode based white noise source
Sample&Hold circuit with internal and external clock source
TECHNICAL SPECIFICATIONS:
Attack time 6ms 850ms
On time 0-1,5s
Decay time 16ms 2s
Off time 14ms – 1,3s
Sustain level +10V
Panel width 22HP
Module depth: 36mm
Power consumption 125mA@+12V, 74mA@-12V
ATTACK DECAY
OFFON
U(V)
t(s)
You will nd Erica Synths terms of warranty at www.ericasynths.lv
Items for return, exchange and/or warranty repair have to be sent to:
Erica Synths
Andrejostas Str. 43
Riga
Latvia
LV-1045
User manual by Girts Ozolins@Erica Synths.
Design by Ineta Briede@Black8.
Copying, distribution or any commercial use in any way is prohibited and needs the
written permission by Erica Synths.
Specications are subject to change without notice.In case of any questions, feel
free to contact us through www.ericasynths.lv.
SAFETY INSTRUCTIONS
Please follow the instructions for use of the Erica Synths module below,cause only this will guarantee proper operation of the module
and ensure warranty from Erica Synths.
The module has to be shipped in the original packaging
only. Any module shipped to us for return, exchange and/or warranty repair has to
be in its original packaging. All other deliveries will be rejected and returned to you.
Make sure you keep the original packaging and technical documentation.
This device complies to the EU guidelines and is manufactured RoHS conforming
without use of lead, mercury, cadmium and chrome. Nevertheless, this device is
special waste and disposal in household waste is not recommended.
Transport the instrument carefully, never let it drop or fall over. Warranty does
not apply to modules with visual damages.
Water is lethal for most of the electric devices, unless they are made waterproof.
This Erica Synths module is NOT intended for use in a humid or wet environment. No
liquids or other conducting substances must get into the module. Should this
happen, the module should be disconnected from mains power immediately, dried,
examined and cleaned by a quali ed technician.
Do not expose the module to temperatures above +50° C or below -2 C. If you have
transported module in extreme low temperatures, leave it in room temperature for an
hour before plugging it in.
FUSION MODULATOR ENVELOPE SHAPE


Produktspezifikationen

Marke: Erica Synths
Kategorie: Nicht kategorisiert
Modell: Fusion Modulator

Brauchst du Hilfe?

Wenn Sie Hilfe mit Erica Synths Fusion Modulator benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Erica Synths

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-