Epson ELPMB62 Bedienungsanleitung

Epson Videostrahl ELPMB62

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Epson ELPMB62 (119 Seiten) in der Kategorie Videostrahl. Dieser Bedienungsanleitung war für 46 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/119

Installation Guide

About This Installation Guide

This guide describes how to mount the ultra-short-throw projectors listed below to a wall using the Epson®

ELPMB62 wall mount.

The following projectors are covered by this guide:

•BrightLink® 1480Fi/1480Fi+

•BrightLink® 1485Fi/1485Fi+

•BrightLink® EB-725Wi/EB-735Fi

•BrightLink® EB-760Wi/EB-770Fi

•PowerLite® EB-720/EB-725W

•PowerLite® EB-750F/EB-755F

•PowerLite® EB-760W

•PowerLite® EB-770F/EB-775F

•PowerLite® EB-800F/EB-805F

The BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ is shown in most illustrations in this guide, but the steps are

the same for all models unless otherwise noted.

Safety Instructions

For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that

ignores instructions in this guide could damage the wall mount or could result in personal injury or property

damage. Keep this installation guide on hand for future reference.

Read the safety instructions in the online User's Guide for your projector and follow the instructions in this

document.

Explanation of Symbols

The warning marks shown below are used throughout this installation guide to prevent personal injury or

property damage. Make sure you understand these warnings when reading this installation guide.

Safety Precautions for Installation

This symbol indicates information that, if ignored, could possibly result in personal injury or even death

due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical

damage due to incorrect handling.

This symbol indicates related or useful information.

Symbol indicating an action that must not be done

Symbol indicating an action that should be done

The wall mount is designed specifically for mounting a projector to a wall. If anything other than a

projector is mounted, the weight may result in damage.

If the wall mount falls, it could cause personal injury or property damage.

Warning

Caution

Warning

English

The installation work (wall mounting) should be performed by specialists who have technical knowledge

and ability. Incomplete or incorrect installation could cause the wall mount to fall and cause personal

injury or property damage.

Follow the steps in this guide to install the wall mount, and be sure to use the bolts and screws specified in

this guide

If the instructions are not followed, this product may fall, resulting in personal injury or an accident.

Handle the power cord carefully.

Incorrect handling may cause fire or electric shock. Observe the following precautions when handling:

• Do not handle the power plug with wet hands.

• Do not use a power cord that is damaged or modified.

• Do not pull the power cord with too much force when routing the cable through the wall mount.

Do not install the wall mount in a place where it might be subjected to vibration or shock.

Vibration or shock could cause damage to the projector or mounting surface. It could also cause the wall mount or

projector to fall and cause personal injury or property damage.

The installation work should be performed by at least two qualified service personnel. If you need to

loosen any screws during installation, be careful not to drop the wall mount.

If the wall mount or projector falls, it could cause personal injury or property damage.

Make sure you use the included safety wire kit when mounting your projector.

Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and

resist any horizontal vibration. Use M10 or 3/8 inch nuts and bolts and make sure to use appropriate wall

anchors for your wall type.

Nuts and bolts smaller than M10 or 3/8 inch could cause the wall mount to fall. Epson accepts no responsibility for

any damage or injury caused by lack of wall strength or inadequate installation.

When you mount the projector on the wall with the wall mount, the wall must be strong enough to hold the

projector and the wall mount.

The maximum combined weight of the projector and wall mount is approximately 41.7 lb (18.9 kg). If the

wall is not strong enough, reinforce the wall before installation.

The installation work should be performed by at least two qualified service personnel. If you need to

loosen any screws during installation, be careful not to drop this product.

If this product falls, it could cause damage or injury.

Inspect the wall mount on a regular basis to ensure there are no broken parts or loose screws.

If there are any broken parts, stop using the wall mount immediately. If the wall mount or projector falls, it could

cause personal injury or property damage.

Never modify the wall mount.

Do not hang on the wall mount or hang a heavy object on the wall mount.

If the projector or wall mount falls, it could cause personal injury or property damage.

Do not use adhesives, lubricants, or oils to install or adjust the wall mount.

If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the part of the

projector attached to the slide plate, the case may crack and cause the projector to fall, resulting in personal injury

or property damage.

Tighten all screws firmly after adjustment.

Otherwise, the projector or wall mount may fall and cause personal injury or property damage.

Never loosen the bolts and nuts after installation.

Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them

firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.

When performing wiring, make sure the cable does not come into contact with any screws or bolts.

Handling the cable incorrectly may cause fire or electric shock.

Warning

Produktspezifikationen

Marke:	Epson
Kategorie:	Videostrahl
Modell:	ELPMB62
Produktfarbe:	Weiß
Befestigungstyp:	Wand
Höchstgewichtskapazität:	- kg
Verpackungsbreite:	300 mm
Verpackungstiefe:	500 mm
Verpackungshöhe:	350 mm
Paketgewicht:	10000 g
Warentarifnummer (HS):	83024190
Ursprungsland:	China
Menge pro Packung:	1 Stück(e)
Kompatible Produkte:	EB-1480Fi / EB-8xx