EPH Elektronik GS24S/06/M/DW DC Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr EPH Elektronik GS24S/06/M/DW DC (13 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/13
Stand: Februar 2011
Z 385 engl
Technical Description
Transistor D.C. Chopper Controller Type GS 24 S
Table of contents
1. Getting started guide
2. General information
2.1. Characteristics
2.2. Accessories
3. Information about the Machine Directive 89/392/EWG
3.1. Delivery
3.2. Installation and start-up
3.3. EMC measures
3.4. Low Voltage Directive
4. Connection options
4.1. Option change of rotating direction
4.2. Connection for change of rotating direction option
5. Manufacturer’s declaration
Copyright © EPH-Elektronik GmbH. All rights reserved. We reserve the right of
ownership and copyright. Any reproduction or other use of the information or materials
provided herein is not permitted without our specific authorisation.
Stand: Februar 2011
Z 385 engl
1. Getting started guide: GS24S/xx-360 with 9-pole screw terminal block
1. Select operating mode on J1 (the default internal mode is Standard, which is obtained
by setting J1 on I).
Select J2 (Standard is internal RF).
2. Connect the following digital input
(Connect terminal 7 to terminal 9; Input for enabling the regulator when J2 is set on
External).
3. Connect the following analogue inputs
Input N set point (terminal 8) voltage 0 to + 10 V or potentiometer (10kOhm)
between terminal 4 and terminal 7, tap from terminal 8.
4. Connect DC motor to terminals 5 and 6.
5. Connect power supply to terminal 3 (-) and terminal 2 (+) (approx. 20 – 36 V DC).
6. Proceed to energise the power supply.
7. LED (power on) lights up on circuit board.
8. The motor turns and the rotation speed can be adjusted via the voltage on terminal 8
(n set-point).
Stand: Februar 2011
Z 385 engl
2. General information / Operation
The series GS 24 S/xx-360 transistor speed controllers are inexpensive devices with
compact dimensions of 72 x 100 mm for the stepless speed control of any DC motors
at low voltages and motor currents of up to 10 A. The input voltage range is 20 to
36 V DC makes a battery operation possible, e.g. from an on-board electrical supply
system or through series SNT 24/xx mains adapters connected upstream. The
stepless speed adjustment can take place through either an internal/external
potentiometer (10kOhm) or through an external reference voltage 0....10 V DC (pre-
selection via jumper set-point). An internal potentiometer acts as an overload
protection by providing a continuously variable motor current limitation.
The possibility to change the rotating direction through a relay is available as an
option using an additional EPH 393 type circuit board. Rotation in the left or right
direction can be pre-selected via a 12 to 48 V DC control signal. during standstill
2.1. Characteristics
â—Ź The high pulse frequency of 18 kHz allows for a quiet operation.
â—Ź Form factor F < 1.05 guarantees reduced motor heating and high MD reserves.
â—Ź Adjustable rotation speed through 0..10 V interface or potentiometer (10kOhm)
(external or internal).
â—Ź Enable-input for output stage activation, internal/external (pre-selection
through jumper RF).
â—Ź Overload protection of motor or drive through stepless current limitation.


Produktspezifikationen

Marke: EPH Elektronik
Kategorie: Nicht kategorisiert
Modell: GS24S/06/M/DW DC

Brauchst du Hilfe?

Wenn Sie Hilfe mit EPH Elektronik GS24S/06/M/DW DC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert EPH Elektronik

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-