Entes DTR-10 Bedienungsanleitung

Entes niet gecategoriseerd DTR-10

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Entes DTR-10 (36 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/36
www.entes.eu
DTR-10 User Manual and
Menu Map
Adr: Dudullu OSB; 1. Cadde; No:23 34776 Ümraniye - İSTANBUL / TÜRKİYE
Tel: Fax: E-mail: Web: +90 216 313 01 10 +90 216 314 16 15 contact@entes.eu www.entes.eu
Call Center Technical Support: 0850 888 84 25 A5299 / Rev.4
1 2
DTR-10, which has a real time clock, is an electronic timer that calculates the sunset and sunrise periods automat-
ically. It is designed for controlling the devices which are connected to its contacts according to sunset, sunrise
and the time periods which are programmed by the user.
ESC Button : It is used to switch between monitoring menus. In the programming mode, it is used to cancel
a parameter change or to return to the previous menu.
SET Button : It is used to switch between monitoring menus. When it is pressed for 3 seconds, programming
YUKARI mode is entered. In the programming mode, it is used to apply a parameter change or to enter
to a menu.
DOWN Buttons :
In the monitoring menu, it is used to switch between programs to show their activity in a day.
When the DOWN button is pressed for 3 seconds, C1 relay goes into manual mode and when
the UP button is pressed for 3 seconds, C2 relay goes into manual mode. In the programming
menu; it is used to browse between menus, to select parameters and to adjust values with digits.
Precautions for Installation and Safe Use
If below precautions are not properly observed and carried out, it may result in cases with injury or death. -
Disconnect power before working on the device.
- When device is connected to the network, do not remove the front panel.
- Do not clean the device with solvent or similar items. Only clean with dry cloth.
- Verify correct terminal connections before energizing the device.
- Install the device on the electrical panel.
- Contact your authorized reseller in case problems occur with your device.
No responsibility is assured by the manufacturer or any of its subsidiaries for any consequences rising
out of the use of this material.
- The output loads connected to the relays do not function if auxiliary supply is absent. Even if the relay status
is monitored as “on”( and/or ), auxiliary supply is a must for the operation.
- There are two reserves in the device. Programmed data is protected by these reserves against power outages.
- For long time reserve, a battery is used. If the device is not continously supplied with voltage and waited on the shelf,
the battery life is 5 years.
- Reserve battery should only be changed by the authorized service.
MANUAL MODE :
In order to use the relay outputs manually, DTR-10 has to be in the monitoring mode. The DOWN button is used to
switch the C1 relay to manual mode and the UP button is used to switch the C2 relay to manual mode. When the UP
or DOWN button is pressed for 3 seconds, “MANUAL” indication appears on the screen. If this is done while the relay
C1 or C2 is activated, that relay will be deactivated. If it is done while the relay C1 or C2 is deactivated, no switching
will occur. When the device is in manual mode and the relay is not energized, and the DOWN button is pressed once
C1 contact will turn o its contact or when the UP button is pressed once C2 contact will turn o its contact at the
end of a 3-second delay. During this delay, the symbol indicating the state of the relay contact is ashing. After the
activation of the contact, when the DOWN button is pressed again for 3 sec, C1 relay will exit the manual mode. When
the UP button is pressed again for 3 sec, C2 relay will exit the manual mode. The relay will stay activated or deactivated
according to the program ow. When both of the the relays are in manual mode, “AUTO” indication will dissappear
from the screen.

Produktspezifikationen

Marke: Entes
Kategorie: niet gecategoriseerd
Modell: DTR-10

Brauchst du Hilfe?

Wenn Sie Hilfe mit Entes DTR-10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung niet gecategoriseerd Entes

Entes

Entes ERB-50 Bedienungsanleitung

6 September 2024
Entes

Entes GEM-10SH Bedienungsanleitung

6 September 2024
Entes

Entes RGSR-24S-OG Bedienungsanleitung

6 September 2024
Entes

Entes RGSR-20S-OG Bedienungsanleitung

6 September 2024
Entes

Entes RG3-15CL Bedienungsanleitung

6 September 2024
Entes

Entes MPR-53S-96 Bedienungsanleitung

6 September 2024
Entes

Entes MPR-47S-L Bedienungsanleitung

6 September 2024
Entes

Entes ETMO-02-DR Bedienungsanleitung

6 September 2024
Entes

Entes MPR-45S-L Bedienungsanleitung

6 September 2024
Entes

Entes MPR-53S-OG-DIN Bedienungsanleitung

6 September 2024

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-

APC

APC C2C Bedienungsanleitung

18 September 2024
APC

APC AP7868 Bedienungsanleitung

18 September 2024
APC

APC P8VNTG Bedienungsanleitung

18 September 2024
APC

APC P62 Bedienungsanleitung

18 September 2024
APC

APC AP7898 Bedienungsanleitung

18 September 2024
Hama

Hama Magnet 00183283 Bedienungsanleitung

18 September 2024
IFM

IFM TD2211 Bedienungsanleitung

18 September 2024
Coyote

Coyote C1CH36FS Bedienungsanleitung

18 September 2024
IFM

IFM AC001S Bedienungsanleitung

18 September 2024
Dimplex

Dimplex SRX120EM Bedienungsanleitung

18 September 2024