Elson Zircon Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Elson Zircon (24 Seiten) in der Kategorie Kessel. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/24
1
Pack Contents
• Zircon unvented water heater incorporating immersion heater(s) & thermal controls
• Factory tted temperature/pressure relief valve (set at 90°C / 1 Mpa (10bar))
• Cold water combination valve assembly
• Expansion vessel & mounting bracket
• Tundish
• 2 Port motorised valve (indirect models only)
• Compression nuts & olives
• Immersion heater spanner
• Installation & servicing instructions
• Guarantee card
IMPORTANT
Please read & understand all these instructions before commencing installation.
Please leave this manual with the customer for future reference.
Zircon Installation Manual
Unvented Direct & Indirect Water Heaters
Installation & Servicing Instructions
2
INTRODUCTION............................................................2
GENERAL REQUIREMENTS........................................3
INSTALLATION GENERAL............................................5
INSTALLATION DISCHARGE........................................7
INSTALLATION DIRECT...............................................11
INSTALLATION INDIRECT...........................................12
COMMISSIONING.......................................................14
MAINTENANCE...........................................................15
USER INSTRUCTIONS...............................................16
FAULT FINDING & SERVICING..................................17
SPARES.......................................................................18
HEAT LOSS.................................................................19
ENVIRONMENTAL INFORMATION.............................19
COMMISSIONING CHECK LIST.................................22
SERVICE RECORD.....................................................23
GUARANTEE...............................................................24
TECHNICAL SUPPORT...............................................24
CONTENTS
The cylinder is a purpose designed unvented water
heater. The unit has a stainless steel inner vessel,
which ensures an excellent standard of corrosion
resistance. The outer casing is a combination of
resilient thermoplastic mouldings and plastic coated
corrosion proofed steel sheet. All products are
insulated with CFC free polyurethane foam to give
good heat loss performance. (see Table 6, page 19)
The unit is supplied complete with all the necessary
safety and control devices needed to allow
connection to the cold water mains. All these
components are preset and not adjustable.
This appliance complies with the requirements of the
CE marking directive and is Kiwa approved to show
compliance with Building Regulations (Section G3).
The following instructions are offered as a guide
to installation which must be carried out by a
competent plumbing and electrical installer in
accordance with Building Regulation G3, The
Building Standards (Scotland) Regulations 1990, or
The Building Regulations (Northern Ireland).
NOTE: Prior to installation the unit should be stored
in an upright position in an area free from excessive
damp or humidity.
THE BENCHMARK SCHEME
Benchmark places responsibilities on both
manufacturers and installers. The purpose is to
ensure that customers are provided with the correct
equipment for their needs, that it is installed,
commissioned and serviced in accordance with the
manufacturer’s instructions by competent persons
and that it meets the requirements of the appropriate
Building Regulations. The Benchmark Checklist can
be used to demonstrate compliance with Building
Regulations and should be provided to the customer
for future reference.
Installers are required to carry out installation,
commissioning and servicing work in accordance
with the Benchmark Code of Practice which is
available from the Heating and Hotwater Industry
Council who manage and promote the Scheme. Visit
www.centralheating.co.uk for more information.
IMPORTANT NOTE TO USER: PLEASE REFER TO
THE USER INSTRUCTIONS SECTION ON PAGE 16
FOR IMPORTANT INFORMATION WITH RESPECT TO
THE BENCHMARK SCHEME
INTRODUCTION
3
IMPORTANT:
THIS APPLIANCE IS NOT INTENDED FOR THE
USE BY PERSONS (INCLUDING CHILDREN)
WITH REDUCED PHYSICAL, SENSORY
OR MENTAL CAPABILITIES, OR LACK OF
KNOWLEDGE AND EXPERIENCE, UNLESS
THEY HAVE BEEN GIVEN SUPERVISION OR
INSTRUCTION CONCERNING THE USE OF THE
APPLIANCE BY A PERSON RESPONSIBLE FOR
THEIR SAFETY.
CHILDREN MUST BE SUPERVISED TO ENSURE
THEY DO NOT PLAY WITH THE APPLIANCE.
SITING THE UNIT
The cylinder must be vertically oor mounted.
Although location is not critical, the following points
should be considered:
• The cylinder should be sited to ensure minimum
dead leg distances, particularly to the point of
most frequent use.
• Avoid siting where extreme cold temperatures
will be experienced. All exposed pipe work
should be insulated.
• The discharge pipework from the safety valves
must have minimum fall of 1:200 from the unit
and terminate in a safe and visible position.
• Access to associated controls and immersion
heaters must be available to provide for the
servicing and maintenance of the system.
Where these controls are installed against a wall a
minimum distance of 250mm must be left (see
Fig. 1).
• Ensure that the oor area for the cylinder is level
and capable of permanently supporting the
weight when full of water. (see Table 1)
WATER SUPPLY
Bear in mind that the mains water supply to the
property will be supplying both the hot and cold
water requirements simultaneously.
It is recommended that the maximum water
demand is assessed and the water supply
checked to ensure this demand can be
satisfactorily met.
Note: A high mains water pressure will not
always guarantee high ow rates.
Wherever possible the mains supply pipe should
be 22mm. We suggest the minimum supply
requirements should be 0.15MPa (1.5 bar) pressure
and 20 litres per minute owrate. However, at
these values outlet ow rates may be poor if
several outlets are used simultaneously. The higher
the available pressure and ow rate the better the
system performance.
The cylinder has an operating pressure of 0.35MPa
(3.5 bar) which is controlled by the cold water
combination valve assembly. The cold water
combination valve assembly can be connected to a
maximum mains pressure of 1.6MPa (16 bar).
OUTLET/TERMINAL FITTINGS (TAPS, ETC.)
The cylinder can be used with most types of terminal
î‚¿ttings. It is advantageous in many mixer showers
to have balanced hot and cold water supplies. In
these instances a balanced pressure cold water
connection should be placed between the 2 pieces
of the cold water combination valve assembly (see
Fig. 2). Outlets situated higher than the cylinder will
give outlet pressures lower than that at the heater, a
10m height difference will result in a 0.1MPa (1 bar)
pressure reduction at the outlet. All î‚¿ttings, pipework
and connections must have a rated pressure of at
least 0.6MPa (6 bar) at 80°C.
GENERAL REQUIREMENTS
Table 1: Unit weights
Fig. 1: Siting the Unit
WALL
Min 250mm Min 250mm
Type Model
Reference
Nominal
Capacity
(litres)
Weight of
unit full
(Kg)
Weight
of unit
(Kg)
Indirect 120zi 120 147 27
150zi 150 182 32
170zi 170 204 34
210zi 210 250 40
250zi 250 294 44
300zi 300 352 52
Direct 120zd 120 144 24
150zd 150 178 28
170zd 170 201 31
210zd 210 247 37
250zd 250 289 39
300zd 300 349 49
Produktspezifikationen
| Marke: | Elson |
| Kategorie: | Kessel |
| Modell: | Zircon |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Elson Zircon benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Kessel Elson
5 August 2024
Bedienungsanleitung Kessel
- Kessel Bosch
- Kessel AEG
- Kessel Siemens
- Kessel ATAG
- Kessel Fagor
- Kessel Teka
- Kessel Inventum
- Kessel Ariston
- Kessel Atlantic
- Kessel ETNA
- Kessel Vaillant
- Kessel Junkers
- Kessel Moa
- Kessel De Dietrich
- Kessel Elba
- Kessel Thermex
- Kessel Remeha
- Kessel Saunier Duval
- Kessel Stiebel Eltron
- Kessel Truma
- Kessel Viessmann
- Kessel Dimplex
- Kessel Buderus
- Kessel Eccotemp
- Kessel Wijas
- Kessel Bulex
- Kessel Nibe
- Kessel Orbegozo
- Kessel Schäfer Heiztechnik
- Kessel Elco
- Kessel Daalderop
- Kessel Eco Heating Systems
- Kessel LEMET
- Kessel Lochinvar
- Kessel Morco
- Kessel MTS
- Kessel Nefit
- Kessel Plieger
- Kessel Quooker
- Kessel Strom
- Kessel Thermona
- Kessel Thermor
- Kessel ACV
- Kessel TTulpe
- Kessel Worcester-Bosch
- Kessel OSO
- Kessel A.O. Smith
- Kessel Agpo Ferroli
- Kessel AWB
- Kessel Cointra
- Kessel Benekov
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
10 Oktober 2024
9 Oktober 2024
23 September 2024
16 September 2024
16 September 2024