Elro AS80KE11 Bedienungsanleitung

Elro Sicherheit AS80KE11

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Elro AS80KE11 (5 Seiten) in der Kategorie Sicherheit. Dieser Bedienungsanleitung war fĂĽr 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/5
1
AS80KE11
WIRELESS KEYPAD
Installation Instructions
General Introduction
The Wireless Keypad is used to Arm/Disarm the system by using a four digit
access code authentication. Users may assign different PIN codes to identify
and allow control by members of the family. The Keypad also incorporates a
Panic function for emergency use and an anti-tamper protection feature that will
immediately initiate a Full Alarm condition when anyone attempts to open its
casing.
Binding
Loosen and remove the locking screw
from the bottom of the Keypad.
1.
Remove the wall mounting plate.
Wall mounting plate
Product Layout
2.
Prepare three AA 1.5V alkaline batteries. Do not insert them into the unit yet.
3.
Log into the ELRO Smart Home Alarm account from a web browser.
4.
Select “System”, then “Add a Device”.
5.
Select “Keypad”.
Setting/low battery LED
Key Meaning of Key
0 - 9 Access code input
Arm
Part-arm 1
Part-arm 2
Disarm
2
6.
The following screen will appear. This means the gateway is entering binding
mode.
7.
Insert the batteries with correct polarity at this point.
8.
The screen below will appear in 10 seconds if the process is successful.
9.
Time-out will occur if the binding process was unsuccessful. Please refer to
the Manual Binding procedure below.
Manual Binding
1.
Repeat steps 5 to 8 of the Binding with ELRO Smart Home Alarm.
2.
Press buttons 1-2-3-4-3, the keypad should enter binding mode.
3.
This screen below will appear in 10 seconds if the process is successful.
Configuration
Set Users and their access codes:
1.
From your account select “SETTINGS”, then “System”.
3
2.
In “Keypad codes”, enter the Username in the first box, and the desired
access code in the second box (it will appear starred).
3.
Click on “+” to enter multiple users and code (code 1, code 2, etc).
Note:
-
Please use a different password for each user.
-
All access codes are not stored in the keypad, instead they are stored in the
gateway and in the cloud platform. This way you can add as many keypads
without having to set up each one.
Operation
1. Setting Security Modes
2. Panic
Press + simultaneously for 2 seconds.
The keypad will emit the radio signal to the system and a full alarm condition will
occur.
3. Keypad self lock
a.
When an incorrect code is entered once, the back light of digits 0~9 will
start to flash 3 times.
b.
If incorrect codes are entered three times consecutively, the keypad will be
locked out for the next 30 seconds. During this period the keypad will not
respond to any keypad press.
c.
Following subsequent lockout of three times, the keypad will alert the
gateway of an unauthorized entry attempt.
4. Tamper Protection
The Keypad incorporates a tamper protection feature to protect against
unauthorized attempts to disassemble it. Any attempt to remove the keypad
from its wall plate will trigger the tamper switch which then initiates an alarm
condition.
a.
First press either the Arm key , Part-arm1 key ,
Part-arm2 key or the Disarm
on the keypad.
b.
Then enter one of the 4-digit access codes created during the
Mounting the Keypad
Tamper
Switch
configuration.
c.
If code entry is correct, the backlight of digits 0~9 on the Keypad will
extinguish. The back light of digits 0~9 will flash three times if
unsuccessful.
Note: See “Keypad self lockout” about unauthorized entry detection.
The Keypad should be mounted in a position close to the main entrance door so
that the access codes can be entered easily.
Ensure that the position selected for the Keypad is within the effective range of
the gateway.
Note: Do NOT fix the Keypad to metalwork or locate the unit within 1 meter of
metalwork (i.e. radiators, water pipes, etc) as this could affect its radio range.

Produktspezifikationen

Marke: Elro
Kategorie: Sicherheit
Modell: AS80KE11

Brauchst du Hilfe?

Wenn Sie Hilfe mit Elro AS80KE11 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheit Elro

Elro

Elro AB600P - MOTION DETECTOR Bedienungsanleitung

17 September 2024
Elro

Elro AG40KE Bedienungsanleitung

17 September 2024
Elro

Elro CS95DVR Bedienungsanleitung

16 September 2024
Elro

Elro AG40PR Bedienungsanleitung

24 August 2024
Elro

Elro ARD51 - V3 Bedienungsanleitung

23 August 2024
Elro

Elro C903IP.2 Home Monitor Bedienungsanleitung

23 August 2024
Elro

Elro C904IP.2 Home Monitor Bedienungsanleitung

20 August 2024
Elro

Elro AS80RE11 Bedienungsanleitung

16 August 2024
Elro

Elro CCD421 Bedienungsanleitung

13 August 2024
Elro

Elro C803IP.2 Home Monitor Bedienungsanleitung

13 August 2024

Bedienungsanleitung Sicherheit

Neueste Bedienungsanleitung fĂĽr -Kategorien-

NetworX

NetworX NX-595E IP Communication Module Bedienungsanleitung

5 Oktober 2024
Unitron

Unitron Smart Alert Systeem Bedienungsanleitung

24 September 2024
NetworX

NetworX NX-408 Bedienungsanleitung

20 September 2024
Theben

Theben Luxa 102.150 - 1020961-2 Bedienungsanleitung

19 September 2024
BTicino

BTicino Classe100 X16E Beveiliging Bedienungsanleitung

16 September 2024
One2track

One2track Safety Angel Bedienungsanleitung

27 August 2024
Sygonix

Sygonix SY-3851632 Bedienungsanleitung

27 August 2024
Sygonix

Sygonix 1326052 Bedienungsanleitung

27 August 2024
Sygonix

Sygonix 43588A WLAN Camera Bedienungsanleitung

27 August 2024
Sygonix

Sygonix 43176S LAN Camera Bedienungsanleitung

27 August 2024