Eliminator Lighting Stealth Spot Bedienungsanleitung

Eliminator Lighting Nicht kategorisiert Stealth Spot

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Eliminator Lighting Stealth Spot (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/6
STEALTH SPOT
©EliminatorŸ Los Angeles, CA. - www.EliminatorLighting.com
Introduction:
The Stealth Beam is a DMX intelligent moving head unit. The Stealth Beam has 3 operating modes;
sound active mode, show mode, or controlled via DMX controller. The Stealth Beam has 2 DMX
Channel modes; 5 or 15 channels. The unit can be run as a stand alone unit or in a Master/Slave set
up. This unit has been tested and there is no assembly required. Follow the instructions on the fol-
lowing pages to operate your fixture. To enhance the beams effects you can use a fog machine.
CAUTION! Please read and understand these instructions before installing or operating this unit.
SPECIFICATIONS:
Model: Stealth Spot
Supply Voltage: 100V-240V 50/60Hz
LED: 1 x 60W White LED
Weight: 11lbs./ 5 kgs.
Size: 6.7” (L) x 9.4” (W) x 13.97” (H)
Fuse: 2 Amp
Power Consumption: 90W
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 2 DMX Channel Modes:
5 Channel Mode &
15 Channel Mode
Gobos: 5 + Spot
Colors: 7 Colors + White
Warranty: 1 Year
CAUTION! Please read and
understand these instructions
before installing or operating
this unit.
Fuse Replacement: Locate and remove
the unit’s power cord. Once the cord
has been removed, the fuse holder is
located inside the power socket. Insert
a flat-head screw driver into the fuse
holder and gently pry out the holder.
Remove the bad fuse and replace with
a new one. The fuse holder has a built-in
second holder for a spare fuse.
©EliminatorŸ Los Angeles, CA. - www.EliminatorLighting.com
AXXX: In this menu you can set the DMX address. Press the Up or Down buttons until “AXXX” is displayed.
“XXX” is the current displayed DMX address. Press Enter and use the UP or Down buttons to nd your de-
sired address. When you have found your desired address press the Enter button to set it. NOTE: To display
the DMX address you must rst select any show, then press the MENU button to exit and then follow
the directions above.
Chnd: The Stealth Spot has 2 DMX channel modes; 5 channel mode and 15 channel mode. In this menu you
can select your desired channel mode. Press the Up or Down buttons until “CHnd” is displayed and press
ENTER. Either “15CH” or “5CH” will be displayed. Use the Up and Down buttons to toggle between the two
modes and press Enter to make your selection and press Menu to exit.
SPnd (Sound Active Speed): In this menu you can adjust the sound active moving speed. Press the Up or
Down buttons until “SPnd” is displayed and press ENTER. Either “LoSP” (Low Speed) or “HISP” (High Speed)
will be displayed. Use the Up and Down buttons to toggle between the two speed and press Enter to make
your selection. Press the Menu button to exit.
SOUN (Sound Active): In this menu you can activate Sound Active mode. Press the Up or Down buttons until
“SOUN” is displayed and press Enter. Either “On” or “O” will be displayed. Use the Up and Down buttons
toggle between the choices and press Enter to make your selection. Press the Menu button to exit.
SHnd (Show Mode): In this menu you can activate the 1 of 8 show mode’s. Press the Up or Down buttons
until “SHnd” is displayed and press Enter. Either 1 of 8 shows will be displayed. Use the Up and Down
buttons nd your desired show and press Enter to make your selection. Press the Menu button to exit
SLnd (Master/Slave): In this menu you can designate the xture as either a Master or Slave in a master-slave
set up. Press the Up or Down buttons until “SLnd” is displayed and press Enter. Either “Mast” or “SL 1 will be
displayed. Use the Up and Down buttons to nd your desired setting and press Enter to make your selection.
Press the Menu button to exit
PAn (Reverse Pan): In this menu you can reverse the Pan function. Press the Up or Down buttons until “PAn”
is displayed and press Enter. Press the Up or Downs buttons until “On” is
displayed, and press Enter. Press the Menu button to exit. This function works better when you have two units
connected in a Master/Slave setup. Have one unit set to reverse Pan and the other unit in normal Pan.
tIL ( Reverse Tilt): In this menu you can reverse the Tilt function. Press the Up or Down buttons until “tIL” is
displayed and press Enter. Press the Up or Downs buttons until “On” is
displayed, and press Enter. Press the Menu button to exit. This function works better when you have two units
connected in a Master/Slave setup. Have one unit set to reverse Tilt and the other unit in normal Tilt.
dISP (Display): In this menu you can “ip” the display 180°. Press the Up or Down buttons until “dISP” is
displayed and press Enter. Either “ON” or “OFF” will now be displayed. If you want to “ip” the display press
the Up button so that “ON” is displayed, and press Enter. Press the Menu button to exit.
rSt (Reset): In this menu you can activate reset function. Press the Press the Up of Down buttons until “rSt”
is displayed and press Enter. The unit will now begin to reset. Press the Menu button to exit.
rFAC (Default Setting): In this menu you can reset the unit to it default settings. Press the Up or Down but-
tons until “rFAC” is displayed and press Enter. Select “On” and press Enter. Press the Menu button to exit.
OPERATION:
UNIVERSAL DMX CONTROL: This unit allows you to use any universal DMX- controller to control head 512
movement, the color wheel, the gobo wheel, and the shutter (strobe). A DMX controller allows you to create
unique programs tailored to your individual needs. Follow the set-up specifications that are included with your
DMX controller.
1. The Stealth Spot has two DMX channel modes; 5 DMX channels and 15 DMX channels.
2. Press the Up or Down buttons until “Chnd” is displayed, and press Enter.
3. Press the Up or Down buttons until your desired DMX channel mode is displayed, and press Enter.
4. Press the Mode button until “AXXX” is displayed. “XXX” is the current displayed DMX addess.
Press the Enter button.
4. Use the Up and Down buttons to find your desired address and press Enter.
5 Connect your DMX Controller and u. se the controller’s faders to control the various DMX fixture traits.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
SOUND ACTIVE MODE:
1. To activate Sound Active mode, press the Up or Down buttons until “SOUN” is displayed, and press Enter.
2. Either “On” or “Off” will be displayed. To activate sound active mode press the Up or Down buttons until
“On” is displayed, and press Enter to select. Press the Menu button to exit
3. To adjust the movement speed in sound active mode press the Up or Down buttons until “SPnd” is
displayed. Either “HISP” (High Speed) or “LoSP” (Low Speed) will be displayed. Use the Up or Down
buttons to switch between the two modes and press Enter to make your selection. Press the Menu button
to exit.
SHOW MODE:
1. To activate Show mode, press the Up or Down buttons until “SHnd” is displayed, and press Enter.
2. 1 of 8 shows will be displayed. Use the Up or Down buttons to scroll through the shows and press Enter
to make your selection. Show 0 runs a random show. Press the Menu button to exit.
MASTER-SLAVE SET UP: This function will allow you to link up to 16 units together and operate without a
controller. The units be sound active or in show mode In a Master-Slave set up one unit will act as the concan . -
trolling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the
units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The
rst unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the
male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. On the Master unit press the Menu button until “SLnd” is displayed, and press Enter. Use the UP and
DOWN buttons to scroll to the “Mast” setting and press Enter. Press the Menu button to exit.
3. After setting the Master unit to the master setting find and set your desired operating mode.
4. On the slave units press the Menu button until “SLnd” is displayed, and press Enter. Press the Up or
Down buttons until “SL 1” and press Enter. Press the Menu button to exit.
5. The slave units will now follow the Master unit.
©EliminatorŸ Los Angeles, CA. - www.EliminatorLighting.com

Produktspezifikationen

Marke: Eliminator Lighting
Kategorie: Nicht kategorisiert
Modell: Stealth Spot

Brauchst du Hilfe?

Wenn Sie Hilfe mit Eliminator Lighting Stealth Spot benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Eliminator Lighting

Eliminator Lighting

Eliminator Lighting Bubbletron EX Go Bedienungsanleitung

4 September 2024
Eliminator Lighting

Eliminator Lighting Mister Kool EP Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting BUBBLETRON EX Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting UVLED 48EL Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting Micro Galaxian Three Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting VF Snow Flurry HO EP Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting BUBBLETRON EXL Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting VF1600 EP Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting Big Shot LED EP Bedienungsanleitung

3 September 2024
Eliminator Lighting

Eliminator Lighting Stryker Max Bedienungsanleitung

3 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024