Electro Harmonix Tri Parallel Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Electro Harmonix Tri Parallel (12 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
TRI PARALLEL MIXER
Effects Loop Mixer/Switcher
Congratulations on your purchase of the Electro-Harmonix Tri Parallel
Mixer! The Tri Parallel Mixer can be used in multiple configurations for a
variety of switching and mixing applications. Use it to switch between or
mix up to three separate effects loops. Send a guitar or other
instrument out to three separate amplifiers, or input three separate
instruments to switch between or mix to a single output. Mix effects in
parallel to create sounds and allow for options not possible when using
effects in series (one after another). These are a few examples of the
multiple ways to incorporate the Tri Parallel Mixer into your setup.
- USING THE TRI PARALLEL MIXER -
Plug the 9VDC adapter into the jack on the top left of the Tri Parallel
Mixer. There are multiple ways to configure your setup, the most typical
configuration is shown below: a guitar based setup for mixing and/or
switching between three separate effects loops.
WARNING: Your Tri Parallel Mixer comes equipped with an Electro-Harmonix 9.6DC-
200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The Tri
Parallel Mixer requires at 9VDC with a center negative plug. Use of the wrong 45mA
adapter or a plug with the wrong polarity may damage your Tri Parallel Mixer and void
the warranty.
In this configuration, plug your guitar or other instrument/sound source
into the INPUT jack on the right of the Tri Parallel Mixer. Connect your
amplifier or other sound destination to the OUTPUT jack on the left of
the Tri Parallel Mixer. All connections can be made using standard ¼”
instrument cables.
Connect the input of the first effect in your first effects loop to the SEND
1 jack. Connect the output of the last effect in your first effects loop to
the RTN 1 jack. Repeat this step for your other two effects loops using
the SEND 2/3 and RTN 2/3 jacks. Below is the signal path in this
configuration:
Use the CH 1/2/3 footswitches to activate their respective effects loops.
Double tap any of these footswitches to enter master bypass, which
connects the INPUT jack directly the OUTPUT jack. When in bypass,
single tap any footswitch to re-enter active mode. There are other
switching options and configuration options that will be discussed later in
this manual.
-GLOBAL CONTROLS / JACKS-
INPUT –This jack on the right of the unit is the master input for the Tri
Parallel Mixer. The signal present here will be outputted to an active
channel’s SEND jack. In master bypass, the input signal connects
directly to the OUTPUT jack.
OUTPUT –This jack on the left of the unit is the master output for the
Tri Parallel Mixer.
MASTER VOL –This knob sets the master output level of the mixer.
DRY VOL –This knob sets how much dry signal (the signal present at
the INPUT jack) is sent to the output of the Tri Parallel Mixer.
MASTER STATUS –This LED lights when the unit is active and doesn’t
light when in master bypass. Double tap any of the three footswitches
to switch from active to bypass mode. When in bypass, single tap any
footswitch to enter active mode. The Tri Parallel Mixer features buffered
bypass.
-CHANNEL CONTROLS / JACKS-
The majority of the controls for the Tri
Parallel Mixer are grouped into three
identical channel sections, each with a
SEND and RTN (Return) jack, a SEND and
RETURN level control, an EQ control, a
PHASE switch, and a footswitch.
SEND 1/2/3 Jack This jack outputs the –
signal inputted to the Tri Parallel Mixer (via
the INPUT jack) when its channel is
active . *Send output impedance = 220Ω.
SEND Knob –This knob sets the level
outputted to the SEND jack.
RTN 1/2/3 Jack –This jack is the input
for a given channel. The signal inputted to
this jack is sent to the OUTPUT jack (after
the EQ control) when its channel is
active . * RTN input impedance = 1MΩ.
RETURN Knob –This knob sets the level of the signal received at the
RTN jack before it is sent to the output of the Tri Parallel Mixer.
PHASE –This switch, when set to 180, inverts the phase of the signal
sent out of the SEND jack. This can be useful when something in your
effects loop is causing phase issues when mixed in with either your dry
signal or other effects loops.


Produktspezifikationen

Marke: Electro Harmonix
Kategorie: Nicht kategorisiert
Modell: Tri Parallel

Brauchst du Hilfe?

Wenn Sie Hilfe mit Electro Harmonix Tri Parallel benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Electro Harmonix

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-