Elation TVL2000 Bedienungsanleitung

Elation Nicht kategorisiert TVL2000

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Elation TVL2000 (10 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/10
©Elation Pr fessionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 2o
TVL2000 General Information
Unpacking: Thank you for purchasing the TVL2000 by Elation Pro-
fessionals®. Every TVL2000 has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are miss-
ing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without con-
tacting customer support rst.
Introduction: The TVL2000 DMX intelligent LED fixture. The TVL2000
has 3 DMX Modes; Two 2 Channel DMX Modes, and a 3 Channel
Mode. The fixture two operating modes; manual mode or DMX con-
trolled. The TVL2000 can only be run as stand alone unit. This fixture is
suitable for theaters, studios, retail stores, and other similar locations.
For best results use fog or special effects smoke to enhance the light
projections.
Customer Support: Elation Professionals -® provides a toll free cus
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.elationlighting.com for any com-
ments or suggestions. Service Hours are Monday through Friday 8:00
a.m. to 4:30 p.m. Pacic Standard Time.
Voice: (323) 582-3322
Fax: (323) 832-9142
E-mail: support@elationlighting.com
To purchase parts online visit http://parts.elationlighting.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
User Instructions
TVL2000
Rev. 1/13
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 15 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
TVL2000 Safety Precautions
©Elation Pr fessionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 4©Elation Pr fessionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 3 oo
• 3 DMX Channel Modes; Two 2 Channel Modes & 3 Channel Mode
• 2 Operating Modes - Manual Mode & DMX Control
• Digital Display for Address and Function Setting
• Power Cord Daisy Chain
TVL2000 Features
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
Elation Professionals®.
During operation the housing may become hot. Avoid touching the
unit with bare hands while in use.
Elation Professionals® will not accept any liability for any resulting dam-
ages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
TVL2000 Handling Precautions
TVL2000 Warranty Registration
The Please îźľll TVL2000 carries a 2 year (730 days) limited warranty.
out the enclosed warranty card to validate your purchase and war-
ranty. You may also register your product online at www.elationlight-
ing.com. All returned service items whether under warranty or not,
must be freight pre-paid and accompany a return authorization (R.A.)
n umber. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact customer support Elation®
for a R.A. number.
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
TVL2000 General Instructions
©Elation Professionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 6©Elation Pr fessionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 5o
Power Supply: The Elation TVL2000 contains an Professionals®
electronic ballast, which will auto sense the voltage when it is plugged
into the power source. With the electronic ballast you do not need to
worry about wall voltage, this unit can be plugged in anywhere. Also
be sure to only use the included I.E.C. power cable supplied with the
unit.
DMX-512: -DMX is short for Digital Multiplex. This is a universal pro
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a sin-
gle controller, as long as all xtures and the controller are DMX com-
pliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The TVL2000 3 DMX channel modes. The DMX address
is set electronically using the controls on the side of the unit. Your unit
and your DMX controller require a approved DMX-
512 110 Ohm Data cable for data input and data
output. We recommend Accu-Cable DMX cables.
If you are making your own cables, be sure to use
standard 110-120 Ohm shielded cable (This cable
may be purchased at almost all professional sound
and lighting stores). Your cables should be made
with a male and female XLR connector on either
end of the cable. Also remember that DMX cable
must be daisy chained and cannot be split.
TVL2000 Set Up
Figure 1
TVL2000 Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
Figure 3
1 Ground 1 Ground
XLR Male Socket XLR Pin Conguration
3 Hot
2 Cold 2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
1
2
3
Termination educes signalr errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4

Produktspezifikationen

Marke: Elation
Kategorie: Nicht kategorisiert
Modell: TVL2000

Brauchst du Hilfe?

Wenn Sie Hilfe mit Elation TVL2000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Elation

Elation

Elation C-LOADER II Bedienungsanleitung

6 September 2024
Elation

Elation PIXEL DRIVER 4000 V3 Bedienungsanleitung

6 September 2024
Elation

Elation PIXEL DRIVER 170IP Bedienungsanleitung

6 September 2024
Elation

Elation PIXEL AMP 200 Bedienungsanleitung

6 September 2024
Elation

Elation KL Panel Bedienungsanleitung

1 August 2024
Elation

Elation Colour 5 Profile Bedienungsanleitung

30 Juli 2024
Elation

Elation Sidewinder Bedienungsanleitung

30 Juli 2024
Elation

Elation Therma Tour 800 Bedienungsanleitung

30 Juli 2024
Elation

Elation WW Profile HP IP Bedienungsanleitung

29 Juli 2024
Elation

Elation Cuepix Blinder WW2 Bedienungsanleitung

27 Juli 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024