E3 F8 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für E3 F8 (2 Seiten) in der Kategorie Fahrradcomputer. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Battery Installation
To help you get started quickly, the computer battery has been installed at the
factory. Under normal usage the battery should last approximately one year.
The F8 uses a 3V CR2032 button cell battery, which is available at most camera
and electronic shops.
NOTE: Most problems that occur with cyclocomputers are caused by a dead or
weak battery. Should you need to replace the battery, follow the steps below.
1. Remove the battery cap from the bottom of the computer using a small coin.
See Figure 1.
2. Install the battery in the battery compartment with the positive (+) side facing the battery cap.
3. Reinstall the battery cap and tighten securely. Note: During a battery change, all data will be cleared from memory. Make a note
of your current wheel size setting and cumulative odometer mileage before replacing the battery so you can reprogram these
values once the new battery is installed (see “Program Wheel Size and “Set the Odometer”).
4. If for some reason the screen is blank or shows an irregular display after a battery change, press the reset button on the
underside of the computer head. See Figure 7.
Computer Functions
CURRENT SPEED (m/h or km/h)
Displays current speed, up to 105mph (168km/h). Accurate to 0.1m/h or km/h. Always displayed at the top of the screen.
SPEED DISPLAY BAR
Provides a graphic display of current speed. Additional segments of bar illuminate as current speed increases.
CLOCK (TIME)
Displays time of day in a 12 hour or 24 hour format.
AUTOMATIC RIDE TIMER (ATM)
Auto start/stop timer is activated by front wheel movement and records actual ride time up to 9:59:59.
TRIP DISTANCE (DST)
Displays distance traveled during current ride (or since last reset), up to 999.9 mi. or km.
ODOMETER (ODO)
Displays cumulative ride distance, up to 99,999 mi. or km.
SPEED COMPARISON ( )56
Compares current speed to average speed. As you ride, a ( ) or (5 6) will appear next to current speed to indicate whether
your current speed is above ( ) or below (5 6) your average speed. This function is automatic, requires no programming
and cannot be disabled.
AVERAGE SPEED (AVG)
Calculates average speed based on ride time (ATM) and trip distance (DST).
MAXIMUM SPEED (MAX)
Displays highest speed attained during a ride (or since last reset), up to 105m/h (168km/h).
Tech Support 1(800)553-8324
0208_3Made in China
F8 Cycle Computer
c
25
c
25
Thank you for your purchase of an E3™ cycle computer. With all the features that a professional rider needs to keep track of a ride,
the F8 is the perfect training tool for any cyclist. The addition of a heavy duty sensor cable makes the F8 an excellent choice o
road as well.
or readings will be inconsistent and erratic. Most problems that occur when installing a new
computer are related to magnet and sensor alignment and spacing.
STEP 4
Once the sensor and wheel magnet are aligned properly, securely tighten both in place and trim
the excess zip-tie ends with scissors.
STEP 5
Route the sensor cable up the back side of the fork blade and secure it with electrical tape or zip-
ties. Be sure to leave enough slack in the cable to allow for the movement of the handlebar while
steering, and the motion of the suspension fork if your bike is equipped with one.
NOTE: Make sure the cable cannot contact the wheel in any way.
STEP 6
Wrap the excess sensor cable around the front brake cable housing, securing with electrical
tape as necessary. When  nished, enough cable slack should remain for the computer
mounting bracket to reach the handlebar. Check to make sure that all excess sensor cable is
either taped down or wrapped around the brake cable housing so that nothing can snag it
during a ride.
BRACKET INSTALLATION
Remove the backing from the small, adhesive rubber pad and apply the pad to the underside of the mounting bracket. Use the
included zip-ties to attach the bracket to the handlebar as shown in Figure 5. Once the bracket is
securely installed, trim the excess zip-tie ends with scissors.
COMPUTER HEAD INSTALLATION
Place the computer head in the bracket and twist the head clockwise until you hear a ‘CLICK,
indicating that the unit is locked in the bracket. See Figure 6. To remove the computer head,
twist the head counterclockwise and then lift it out of the bracket.
TEST OF INSTALLATION
Once installation is complete, test the unit to make sure everything is adjusted and working
properly. Pick up the front end of the bicycle and spin the front wheel. The computer should
register a speed reading within 1-2 seconds. If not, check the alignment of the wheel magnet
and sensor, and make sure that the space between the magnet and sensor is 3mm or less.
Adjust as necessary and re-test.
Reset Display Screens
The ATM, DST, AVS and MAX display screens are reset simultaneously. In the Automatic Ride
Timer display screen (ATM), press and hold both the LEFT and RIGHT buttons for four seconds
to reset the data in all four screens.
Maximum Speed can also be reset independently. In the Maximum Speed display screen (MAX),
press and hold both the LEFT and RIGHT buttons for four seconds to reset Maximum Speed.
To reset ALL display screens and ALL programmed settings (including Clock, Odometer,
and wheel size setting), depress the reset button on the underside of the computer
head. See Figure 7.
1-3 mm
LOCK
UNLOCK
1
3
4
5
6
7
STEP 3
Press the RIGHT button to con rm your selection and advance to the wheel size setting screen.
(PROGRAM WHEEL SIZE)
STEP 4
After the speed scale has been selected, the computer will automatically advance to the wheel size programming screen. The digit
at the right of the screen will  ash. Press the LEFT button to adjust the  ashing digit according to the wheel circumference value
determined above. Press the RIGHT button to advance to the next  ashing digit.
STEP 5
Repeat this sequence until all digits have been set to the appropriate value. Then press the RIGHT button to advance to the
odometer setting screen.
(SET THE ODOMETER)
STEP 6
The digit at the right of the screen will  ash. (Note: If you dont want to change the odometer setting, press the RIGHT button  ve
times to exit the set-up mode and return to the Odometer display screen.) Press the LEFT button to adjust the  ashing digit. Press
the RIGHT button to advance to the next  ashing digit.
STEP 7
Repeat this sequence until the odometer has been set to the appropriate value. Then press the RIGHT button to exit the set-up
mode and return to the Odometer display screen.
Set the Clock
The F8 is equipped with a digital clock that displays time of day in a 12 hour or 24 hour format.
STEP 1
Press the RIGHT button to advance to the Clock display screen (TIME). In the Clock display screen (TIME), press and hold the RIGHT
button for three seconds.
STEP 2
“12” or “24” will  ash in the lower line of the display. Press the LEFT button to select 12 hour or 24 hour mode. Press the RIGHT
button to con rm your selection and advance to the hours setting.
STEP 3
The hours will  ash. Press the LEFT button (or press and hold) to advance the hours. Press the RIGHT button to advance to the
minutes setting.
STEP 4
The minutes will  ash. Press the LEFT button (or press and hold) to advance the minutes. Press the RIGHT button to set the time
and return to the Clock display screen.
Installation
We recommend that you install the F8 in the following manner, starting with the sensor unit on the fork and working up to the
mounting bracket on the handlebar.
WHEEL MAGNET AND SENSOR INSTALLATION
STEP 1
Determine whether you will mount the computer head to the left or right of your handlebar stem. The sensor should be attached
to the fork on the same side of the bike as the computer head.
STEP 2
Using the included zip-ties, mount the sensor loosely (so that you can slide it around) to the fork blade. See Figure 3. The sensor
can be mounted at any point along the fork, but mounting the sensor slightly higher on the fork blade and running the cable up
the back side of the fork will o er better protection from rocks, branches and other snags.
STEP 3
Attach the wheel magnet loosely to one of the spokes on the same side of the wheel as the sensor. Adjust the position of the
magnet and sensor by sliding both pieces up or down to achieve 1-3mm of clearance between the two (1mm is about the
thickness of a penny). See Figure 4. If the magnet and sensor are not close enough, the computer will not pick up a reading
AUTO SLEEP
To prolong battery life, the F8 will automatically enter sleep” mode after minutes of non-use. The computer will automatical10 ly
restart as soon as it receives input from the speed sensor, or when any button is pressed.
SCAN MODE
Allows hands free viewing of all display screens. When scan mode is activated, the computer will scroll through all display screens
on a continuous loop, displaying each screen for two seconds. To activate scan mode, press and hold the LEFT button for three
seconds in any display screen. To exit scan mode, press the LEFT or RIGHT button in any display screen.
Determine Wheel Size:
The F8 uses wheel circumference (measured in millimeters) to calculate speed and distance. Before you can program the F8 you
must calculate wheel circumference using one of the three methods below.
1. Select size from chart (least accurate): Use the chart below to  nd the circumference for your tire size. The chart lists the
programming sizes for some of the most popular tire sizes currently in use. These numbers are estimations which may not
precisely match the circumference of your wheel, due to variations in tire size between brands and models.
2. Measure wheel diameter (more accurate): Measure your wheel diameter (including wheel and tire) in millimeters (1 inch =
25.4mm) and multiply by 3.1416. This value is your wheel circumference.
3. Perform roll-out test (most accurate): See Figure 2.
STEP 1
Stand your bicycle upright. With your tire in ated to its
proper pressure, rotate your front wheel so that the valve is
located at the bottom (6 oclock position). Make a mark on
the  oor to indicate the valve location.
STEP 2
Roll the bicycle forward in a straight line for one complete
wheel revolution, until the valve is again at the bottom
(ideally, you should be on the bike). Make a mark on the
oor to indicate the valve location.
STEP 3
Measure the distance between the marks in millimeters
(1 inch = 25.4mm). This value is your wheel circumference.
Program the Computer
Before using your F8, you must program wheel size (see
“Determine Wheel Size, above), select a speed scale (miles
or kilometers), set the odometer (if desired) and set the
clock. The  rst step is to select the speed scale.
Select Miles or Kilometers, Program
Wheel Size & Set the Odometer
The F8 is capable of displaying speed and distance
information in either miles or kilometers. Also, the
odometer can be programmed so that cumulative
mileage can be restored after a battery change or
transferred from another computer.
(SELECT MILES OR KILOMETERS)
STEP 1
Press the RIGHT button to advance to the Odometer display screen (ODO). In the Odometer display screen (ODO), press and hold
the RIGHT button for three seconds.
STEP 2
“km/h or “m/h will appear on the right side of the screen. Press the LEFT button to select miles (m/h) or kilometers (km/h).
16 x 1.75
20 x 1.75
26 x 0.75
24 x 1.75
24 x 1
1272
1590
1948
1907
1954
26 x 1.0
26 x 1.6
26 x 1.5
26 x 1
1973
2105
2026
2051
26 x 1.75
26 x 2
26 x 2
26 x 1.9
2070
2089
2114
2133
TIRE SIZE CIRCUMFERENCE
1/8
3/8
3/8
27 x 1
28 x 1.5
28 x 1
28 x 1
28 x 1.75
2199
2224
2268
2265
2205
700 x 18c
700 x 25c
700 x 23c
700 x 20c
2102
2114
2133
2146
700 x 28c
700 x 40c
700 x 37c
700 x 32c
2149
2174
2205
2224
TIRE SIZE CIRCUMFERENCE
3/8
1/2
1/4
1x
Distance in mm / inch
2


Produktspezifikationen

Marke: E3
Kategorie: Fahrradcomputer
Modell: F8

Brauchst du Hilfe?

Wenn Sie Hilfe mit E3 F8 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fahrradcomputer E3

E3

E3 F8 Bedienungsanleitung

22 Februar 2024

Bedienungsanleitung Fahrradcomputer

Neueste Bedienungsanleitung für -Kategorien-