Dremel 6000 Bedienungsanleitung

Dremel Schleifmaschine 6000

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dremel 6000 (35 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 36 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/35
Contour Sander
Owner’s Manual
Model 6000
HONESTLY NOW … Have you read
this OWNER’S MANUAL?
26109 Printed in 25476 10/04 Mexico
©
Robert Bosch Tool
Corporation
1997
all rights reserved
P.O. Box 1468
Racine, Wisconsin 53401
1-800-437-3635
http://www.dremel.com
•Safety
•Assembly
•Operation
•Maintenance
•Accessory Information
•Warranty
• Service Parts
Parlez-vous français?
Voir page 12
¿Habla español?
Vea página 23
Dremel brand products are manufactured and sold by the
Dremel Division of Robert Bosch Tool Corporation
DM 2610919361 9/03 9/5/03 8:33 AM Page 1
Read and understand all instructions. Failure to follow all instructions
listed below, may result in electric shock, fire and/or serious personal
injury.
SAVE THESE INSTRUCTIONS
-2-
Work Area
Keep your work area clean and well lit.
Cluttered benches and dark areas invite
accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the
dust or fumes.
Keep by-standers, children, and visitors
away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
Double Insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified
electrician to install a polarized outlet. Do
not change the plug in any way. Double
Insulation eliminates the need for the
three wire grounded power cord and
grounded power supply system. Before
plugging in the tool, be certain the outlet
voltage supplied is within the voltage marked
on the nameplate. Do not use “AC only”
rated tools with a DC power supply.
Avoid body contact with grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased
risk of electric shock if your body is
grounded. If operating the power tool in
damp locations is unavoidable, a Ground
Fault Circuit Interrupter must be used to
supply the power to your tool. Electrician’s
rubber gloves and footwear will further
enhance your personal safety.
Don't expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the
cord to carry the tools or pull the plug
from an outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
Replace damaged cords immediately.
Damaged cords increase the risk of electric
shock.
When operating a power tool outside, use
an outdoor extension cord marked "W-A"
or "W." These cords are rated for outdoor
use and reduce the risk of electric shock.
Refer to “Recommended sizes of Extension
Cords” in the Accessory section of this
manual.
Personal Safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts.
Keep handles dry, clean and free from oil
and grease.
Avoid accidental starting. Be sure switch
is “OFF” before plugging in. Carrying tools
with your finger on the switch or plugging in
tools that have the switch “ON” invites
accidents.
Remove adjusting keys or wrenches
before turning the tool “ON”. A wrench or
a key that is left attached to a rotating part of
the tool may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times. Proper footing
and balance enables better control of the
tool in unexpected situations.
Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions.
Tool Use and Care
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
!
WARNING
Power Tool Safety Rules
DM 2610919361 9/03 9/5/03 8:33 AM Page 2
-3-
Contour Sander Safety Rules
or against your body is unstable and may
lead to loss of control.
Do not force tool. Use the correct tool for
your application. The correct tool will do
the job better and safer at the rate for which
it is designed.
Do not use tool if switch does not turn it
“ON” or “OFF”. Any tool that cannot be
controlled with the switch is dangerous and
must be repaired.
Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally. Store
idle tools out of reach of children and
other untrained persons. Tools ar e
dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely
to bind and are easier to control. Any
alteration or modification is a misuse and
may result in a dangerous condition.
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool
serviced before using. Many accidents are
caused by poorly maintained tools. Develop
a periodic maintenance schedule for your
tool.
Use only accessories that are
recommended by the manufacturer for
your model. Accessories that may be
suitable for one tool, may become hazardous
when used on another tool.
Service
Tool service must be performed only by
qualified r epair personnel. Service or
maintenance performed by unqualified
personnel could result in a risk of injury. For
example: internal wires may be misplaced or
pinched, safety guard return springs may be
improperly mounted.
When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow
Maintenance Instructions may create a risk of
electric shock or injury. Certain cleaning agents
such as gasoline, carbon tetrachloride,
ammonia, etc. may damage plastic parts.
Unplug the sander before changing
accessories. Accidental start-ups may
occur if sander is plugged in while changing
an accessory.
If your tool is equipped with a dust bag,
empty it frequently and after completion
of sanding. Be extremely careful of dust
disposal, materials in fine particle form may
be explosive. Do not throw sanding dust on
an open fire. Spontaneous combustion, may
in time, result from mixture of oil or water
with dust particles.
Always wear eye protection and a dust
mask for dusty applications and when
sanding overhead. Sanding particles can
be absorbed by your eyes and inhaled easily
and may cause health complications.
Use special precautions when sanding
chemically pressure treated lumber, paint
that may be lead based, or any other
materials that may contain carcinogens. A
suitable breathing respirator and protective
clothing must be worn by all persons
entering the work area. Work area should be
sealed by plastic sheeting and persons not
protected should be kept out until work area
is thoroughly cleaned.
Do not wet sand with this sander. Liquids
entering the motor housing is an electrical
shock hazard.
Do not use sandpaper intended for larger
sanding pads. Larger sandpaper will extend
beyond the sanding pad causing snagging,
tearing of the paper or kick-back. Extra
paper extending beyond the sanding pad
can also cause serious lacerations.
Clamp or secure workpiece when
sanding. Clamping the workpiece prevents
it from being ejected from under the sander
and leaves both hands free to control the
tool.
Keep the cord away from the accessory.
The cord can become entangled with the
pad or contour.
DM 2610919361 9/03 9/5/03 8:33 AM Page 3

Produktspezifikationen

Marke: Dremel
Kategorie: Schleifmaschine
Modell: 6000

Brauchst du Hilfe?

Wenn Sie Hilfe mit Dremel 6000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Schleifmaschine Dremel

Dremel

Dremel 400seriesXPR Bedienungsanleitung

17 September 2024
Dremel

Dremel 780 Bedienungsanleitung

15 August 2024
Dremel

Dremel 10.8V Lithium-ion Bedienungsanleitung

7 August 2024
Dremel

Dremel 300series Bedienungsanleitung

4 August 2024
Dremel

Dremel 300 Bedienungsanleitung

3 August 2024
Dremel

Dremel 6000 Bedienungsanleitung

24 Juni 2023

Bedienungsanleitung Schleifmaschine

Neueste Bedienungsanleitung für -Kategorien-

Makita

Makita GA9060R Bedienungsanleitung

15 Oktober 2024
Hitachi

Hitachi G 13SR Bedienungsanleitung

14 Oktober 2024
Makita

Makita DGA700Z Bedienungsanleitung

13 Oktober 2024
Metabo

Metabo WP820-115 Bedienungsanleitung

8 Oktober 2024
DeWalt

DeWalt DW887N Bedienungsanleitung

7 Oktober 2024
Milwaukee

Milwaukee 0725-21 Bedienungsanleitung

5 Oktober 2024
Makita

Makita GA013GD101 Bedienungsanleitung

3 Oktober 2024
Milwaukee

Milwaukee 2784-20 Bedienungsanleitung

3 Oktober 2024
Ryobi

Ryobi RAG800-115 Bedienungsanleitung

2 Oktober 2024
Makita

Makita GA022GD202 Bedienungsanleitung

2 Oktober 2024