Drayton Digistat 2290B Bedienungsanleitung

Drayton Thermostaat Digistat 2290B

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Drayton Digistat 2290B (4 Seiten) in der Kategorie Thermostaat. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
Programmable Room
Thermostat
Installation Guide
Model: 2290B
1. Remove th frone t cover by releasing th 2 screwe s a the t
bottom. Mo ting holeun s and electrical connections are
found u erneatnd h the hinged black cover (Fig 1).
Before Installation
If you do not have the knowledge to install the
thermostat safely then you must arrange for a
competent electrician or heating engineer to install it
for you. Wiring must conform to the current IEE
regulations.
Prior to commencing the installation you must ensure
the mains supply is switched off.
Digistat
3r Generationd
(Fig 1)
(Fi 3)g
(Fig 4)
(Fig 6)
(Fig 7)
(Fig 2)
2. Fix back plate directly onto the wall using suitable wal plugs l
and screws or mount over existing wall box (Fig 2).
3. Complete the wiring a ording to the con ction suggestions cc ne
4. Close the black hinged ter nami l cover and rep cla e the front
shown n g i (Fi 3). For Basi bo erc il , Combi bo er an Basic il d
bo er withil e e zon valv ap icationpl s t Digista with y batter or
mains supply are suitable.
For Electric Heat application use
Digistat
with mains
supply only.
cover by locating the tw lao tches at the top the fasten n the
2 screws at the bottom (Fig 4).
(Fig 5)
7. Replace the battery cover (Fig 7).
5. Remove th battery cover by s dine li g the battery cover at the
bottom downwards (Fig 5).
6. Install th 2 Ae A batteries provided (Fi 6).g
control the room temperature.
8. The is Digistat now installed and will automatically start to
Technical Helpline Tel: 0333 6000 622
Website: www.draytoncontrols.co.uk
Email: customer.care@draytoncontrols.co.uk
UserandInstallationGuide06490308001IssD
INSTA ER OPTIONSLL
To make changes to the default Installer Options shown below,
enter th Installee r Options menu b pressing thy e setting tton s bu
for 3 se onc ds. This allows access to the User Menu 01, the
Advance User Setting Mend s u 02, th Installer Setting 03e s , and
Service Interval Setting 04. Uss e th + ane d - ttonbu s to scroll to
Installer Options and press O to select. You can exit the menu by
pressing until you have returned to the home screen. I the n
Installer Options menu (Fig 8), scroll thr gh thou e options using
the + and - ttonbu s and pres ts O o select. Scroll thr gou h the
dierent setting usins g the + and - ttonbu s and pres ts O o select
and save. (Fig 9 shows Option 02 OFF).
(Option 01) Partial Assistant (beep)Sight
When enabled, audible to es indicate when the setpo is n int
more than, less than or equal to the current room te perature m
wh us manually adjusts the setpo tton: en a er int using the + bu
Setpo room te perature int > m - single high to 0.5°C ne per
increase
Setpo temperature int = room - double to e n
Setpo room te perature int < m - single low per tone 0.5°C
decrease
(Option 02) Frost Protection
The Digistat will switch on the heating the te falls if mperature
to and mai tains te perature even when 5°C n a m of 7°C
in OFF mode.
(Option 03) Minimum Setpoint Limit
Change minimum setpoi temperature. After any changes to nt
setpoi limits, all setpoi ts in AUTO, MANUAL, BOOST and nt n
HOOLIDAY modes will be modified to conform accordingly.
(Fig 8) (Fig 9)
(Option 04) Maximum Setpoint Limit
Change changes maximum setpoi temnt perature. After any to
setpoi lim setpoi and nt its, all nts MANUAL, in AUTO, BOOST
HOOLIDAY modes will be modified to conform accordingly.
(Option 05) Optimum Start
Whe the n enabled, this uses current temperature, ambient
next sche setpoi capt the duled nt and data heat gain ured by
device to adjust the thermostat early, setpoint so the ambient
tem req starts.perature is at the uired level when the next event
Delayed Start
Whe current n enabled, this uses current temperature, ambient
event setpoi environment nt characteristics and heating of the
to the delay the implementation of setpoint if ambient
temperature is to it, refore already close the saving energy.
(Option 06) Protection Valve Time
In ronic heating systems some hyd it uired to may be req protect
the it given valve operating by for a time. When enabled, this
main tpu operated tenance feature ensures that each relay ou t is
for at ute least (1) one min each week.
(Option 07) sor lt Sen Fau Function
In central heating the event fault, of a sensor outpu is reduced t
to ng heating ON 30% by turni for 3 minutes, then OFF for 7
minutes.
(Option 08) Application Type
Select the central heating system energy type.
(Option 09) System Capability
Select the flow capability of the heating system.
(Option 13) Settings Installer Lock
When enabled, installers settings can lock the installer menu
until a 3 digit code the code is entered. If is forgotten while
device call the Technical is locked, please Helpline.
(Option 20) Reset (Service Interval settings are NOT reset)
Reset to the Digistat its factory original settings.
Service Interval Options continued on reverse.
User Guide
INSTA ER OPTIONSLL - contin due
Pre- t Progra 1 (5-2dase m y w kend):ee
1Event 2 3 4 (5)* (6) (7) (8)
Time 06:30 0 30 16:30 22 08: :3
20°CTemperature 16°C 21°C OFF
Power supply 2x A 1.5V alkalinA e batteries
Switch type & rat gin 3(1)A at 230V/50Hz
current
Min. recommended
Ambient te eramp ture
SPDT (voltage free contacts)
10mA@24VAC (induc ve)ti
(Si Option 01) Si Status
Enabl o sable r di e Service Interva Mode.l
(S Optio 02 S Typei n ) i
Selec eec impo o tht t sed n e heating n e s whe servic i due.
(S Optio 03 Service Due Datei n )
Se datt e n t e s whe nex servic i due.
(Si Optio 04) Warningn
Selec no. of day befor servict s e e e du date.
(S Optio 05 Service Due Alarmi n )
Enable or disable the audible service due alarm.
(Si Option 06) Si Bo sto
Enable or disable the Service Boost feature (5 boosts).
(Si Option 07) Password Res te
Chang th 4 digi PIN. If yo forge your Si password, e e t u t
pleas cal the Technica Helpline.e l l
Technical Data
Ambient hu dity mi
Operating: 0°C to +40°C
Storage: -20°C to 65°C
(non c densing)on 20% t 80%o , 90% no ondn-c ensing
Te eramp ture range 5°C to 30°C
4KVRated impuls voltagee
75°C
Ball pre ure testss
1BDisconnection means
Automatic action 100, 0 cycles00
Operating Frequency 2402-2480 MHz
Max RF Power
transmitted +10dBm
Degree 2
Po ution ll sit tionua
IP30Protection level
Wiring
I = 2%V
Energy C ssla
comply wit IE wirin regulationsh E g
Relevant EC Directives: 2014/53/EU (RED)
2011/65/E (RoHS) U
2012/19/E (W E)U EE
Standards: EN 60730-1
EN 60730-2-7
EN 60730-2-9
ESTI E 300 328N
EN IEC 63000
ESTI E 301 489N
The Drayton thermostat is iversalDigistat a un thermostat with
24 hour, 5-2day or 7day program types and up to 8 time/
te peraturem events per day and can also be d a use as simple
room thermostat.
Clock Setting
•Press and hold the cog button until User 01 appears,
•Press the plus button to Advanced 02, then press O to
enter,
•Press O to enter Time settings,
•Using the + and - you can adjust the time, then press O
to save,
•Press the cog button twice to bring you back to the
home screen.
General Operation
Programmable thermostats do not have “On” and “Off” times
like traditional timers. They offer temperature control both
day and night and you simply select which temperatures you
require at each point in the day.
With the unit in “Auto Mode” (the calendar icon is visible at
the bottom of the screen) the temperature can be changed for
a short time by using the + and – buttons. Changing the
temperature in this way will keep the Digistat set to your new
temperature until the next pre-programmed event (at which
time it will revert to programmed temperature). The
temperature you are setting will flash on the screen. Once
temperature is set, the unit will revert to showing the room
temperature again. The indicator will show on the screen if
the unit is calling for heat.
Programming the Digistat
Your comes with the following settings Digistat
pre-programmed for your convenience and is suitable for
those working out of the house during a typical 9-5 pattern.
When the 5-2day program type is selected the pre-set
temperatures will be different Mon-Fri and Sat-Sun, as per
the tables below:
Pre-s Program et 1 (24h, 5-2day we kdays, e or 7day):
1Event 2 3 4 (5)* (6) (7) (8)
Time 07:00 09:00 16:00 23:00
20°CTemperature 18°C 21°C OFF
Here y, Sc id r El c ro s K Lt , res b hne e ectri Cont l U d decla that Digis t B ta 2290
is in com ce th D e plian wi irectiv 2014/53 . /EU
Th de la ate c r ion f formity may be o con consulted at
www.d oncon ls.rayt tro co.uk
* these l To add additiona time eri ll x. p ods manua y (ma 8 per le day) p ase
refer to the steps to the right.
Th luetoote B h® word ma an logos ark d re register red t ademarks ow ned
by Bluetooth SIG, I .nc and any use of such ma s brk y S i r E c is chne de lectri
u r li . O r tr s and tr e s are t e of t nde cense the ademark ad name hos heir
r p ive ow rs.es ect ne

Produktspezifikationen

Marke: Drayton
Kategorie: Thermostaat
Modell: Digistat 2290B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Drayton Digistat 2290B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Thermostaat Drayton

Drayton

Drayton RTS2 Bedienungsanleitung

16 September 2024
Drayton

Drayton Digistat RF902 Bedienungsanleitung

6 September 2024
Drayton

Drayton Digistat RF901 Bedienungsanleitung

6 September 2024
Drayton

Drayton PTS1 Bedienungsanleitung

6 September 2024
Drayton

Drayton LP20RF & Digistat+ RF Bedienungsanleitung

6 September 2024
Drayton

Drayton Easy 2 Bedienungsanleitung

6 September 2024
Drayton

Drayton Digistat+1RF Bedienungsanleitung

6 September 2024
Drayton

Drayton Digistat+C RF Bedienungsanleitung

6 September 2024
Drayton

Drayton HTS3 Bedienungsanleitung

6 September 2024
Drayton

Drayton Digistat 2290B Bedienungsanleitung

6 September 2024

Bedienungsanleitung Thermostaat

Neueste Bedienungsanleitung für -Kategorien-

Theben

Theben RAM 801 top Bedienungsanleitung

18 September 2024
Weishaupt

Weishaupt Modul Control WCM-FS 2.0 Bedienungsanleitung

18 September 2024
AWB

AWB ExaControl VM-1 Bedienungsanleitung

17 September 2024
Vemer

Vemer TAMB cap Bedienungsanleitung

17 September 2024
Theben

Theben RAM 797 HF set 4 Bedienungsanleitung

16 September 2024
Theben

Theben RAMSES 725 Thermostaat Bedienungsanleitung

16 September 2024
Theben

Theben RAMSES 798 Thermostaat Bedienungsanleitung

16 September 2024
Theben

Theben RAMSES 707 Thermostaat Bedienungsanleitung

16 September 2024
Theben

Theben RAMSES 746 Thermostaat Bedienungsanleitung

16 September 2024
Honeywell

Honeywell SMHOM8610KIT Bedienungsanleitung

15 September 2024