Dormakaba RCI F1119 Bedienungsanleitung

Dormakaba niet gecategoriseerd RCI F1119

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Dormakaba RCI F1119 (2 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war fĂĽr 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
I N S T A L L A T I O N
© 2015 RutheRfoRd ContRols Int’l | A doRMA GRoup CoMpAny
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com
When installing an electric strike on an inactive door of a set of double doors, it can be treated the same as a frame installation in most situations. For
more information contact the Technical Service Department at 1-800-265-6630 or 519-621-7651.
Fire labeled heavy-duty electric strike
F1119
isf1119 Pcn14079
r06/15Gr-1
INSTRUCTIONS
1. To determine if the Strike Shim positions need adjustment, measure dimension “R” (see Figure 1) from the center to the edge
of the latch. When necessary rearrange Strike Shims according to the chart below. The “shipped as default” positions are
illustrated in Figure 2.
SHIM PLACEMENT CHART
Note: Shims consist of two thin and one thick. Install with the indicated hardware per the appropriate measurement R range.
Shipped as Default
Figure #1 Figure #2
S1 S2
“R” distance
from center to
edge of latch
“R” distance from
center to edge of latch
Deadlock
Trigger
Deadlock
Trigger
Mortise Lock Cylindrical Lock
Measurement “R” “S1” Shims “S1” Screws “S2” Shims “S2” Screws
5/16” (8.2mm) or Less None M4 x 10mm 1 thick, 2 thin M4 x 10mm
5/16” - 3/8”, (8.2 - 9.7mm) 1 thin M4 x 10mm 1 thick, 1 thin M4 x 10mm
3/8” - 7/16”, (9.7 - 10.7mm) 1 thick M4 x 10mm 2 thin M4 x 10mm
7/16” - 1/2”, (10.7 - 12.2mm) 1 thick, 1 thin M4 x 14mm 1 thin M4 x 10mm
1/2” - 9/16” (12.2 - 13.7mm) 1 thick, 2 thin M4 x 14mm none none
INSTRUCTIONS Cont’d.
2. Determine the horizontal centerline.
FOR MORTISE LOCKS: Position the strike against the edge of
the door with the deadlock trigger fully on the strike’s angled
ramp and the latch within the strike cavity. Move door close to
the frame. The horizontal centerline is clearly molded into the
strike’s pry-guard. Transfer onto door frame.
FOR CYLINDRICAL LOCKS: Simply align the center of the
latch with the center of the strike cavity. Move door close to
the frame. The horizontal centerline is clearly molded into the
strike’s pry-guard. Transfer onto door frame.
3. Determine the vertical centerline of the door lock face,
carefully considering any stops or gasket and transfer onto
the door frame.
4. Use the vertical and horizontal centerlines marked on the
drawing below to prepare the door frame for cutting.
5. If required, install the optional “no weld” mounting brackets
as per the instructions included with the mounting brackets
in the hardware pack.
6. Connect the incoming wiring from the power supply to the
terminal screws on the strike insert. RCI door strikes are
not polarity sensitive although be certain to observe proper
polarity if a suppression diode is required for access control
applications. To meet BHMA A156.31 install the MOV
provided across the red & black power wires.
7. Install the door strike in the door frame using the screws
provided.
I N S T A L L A T I O N
Fire labeled heavy-duty electric strike
F1119
© 2015 RutheRfoRd ContRols Int’l | A doRMA GRoup CoMpAny
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com
F1119
Vertical Centre Line of Door
Lock and Mounting Face Plate
A 1 3/8” 1.38 34.9
B 9” 9.0 228.6
C 3-3/4” 3.75 95.3
D 1 1/2” 1.50 38.1
E 5/16” 0.31 7.8
F 5/32” 1.56 4.0
G 1-7/8” 1.88 47.6
X
K 8-3/8” 8.38 213.0
M 12-24 N/A N/A
MEASUREMENT
FRACTIONAL
INCHES
DECIMAL
INCHES
METRIC
mm
In or Out... we make it Easy!®
NOTE: Specifications subject to change without notice.
* Dimension F is measured from face of mounting tab to face of frame.
MOUNTING TAB KIT INSTRUCTIONS
Mounting tab kit is for use with aluminum and steel frames that
do not have factory installed mounting tabs for electric strike
installation.
1. Prepare the frame as shown in the installation instructions
(shipped separately with corresponding products). Fasten
the mounting tabs to the faceplate of the strike, selecting the
appropriate shims for your installation.
2. Using the assembled strike and tabs as a template, place
against the frame and mark the mounting hole locations.
Remove and drill a 3/16” hole in frame for each mounting tab
and countersink the frame.
3. Remove the tabs from the faceplate and install in the frame
using the 12-24 x 3/8” machine screws supplied. Tabs are zinc
plated and drilled and tapped for this purpose.
4. Make final electrical connections as described in installation
instructions (separate) and mount strike to the tabs with the
12-24 x 3/8” machine screws.
Frame
Self-Adhesive
Mounting Shim (8
incl.)
Mounting bTa
(2 incl.)
12-24 Machine
Screws (2 each to
keep tab straight)

Produktspezifikationen

Marke: Dormakaba
Kategorie: niet gecategoriseerd
Modell: RCI F1119

Brauchst du Hilfe?

Wenn Sie Hilfe mit Dormakaba RCI F1119 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung niet gecategoriseerd Dormakaba

Dormakaba

Dormakaba HSW-GP Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba DKX-10 Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba Confidant RFID Kit 1 Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba DKX Type IV Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba Keyscan Aurora Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba HSB-M01 Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba DKPS-4A Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba X-ZONE T Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba Keyscan LUNA Bedienungsanleitung

21 August 2024
Dormakaba

Dormakaba RCI 4 Bedienungsanleitung

21 August 2024

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Siemens

Siemens SZ73010 Bedienungsanleitung

17 September 2024
IFM

IFM IF5888 Bedienungsanleitung

17 September 2024
Livarno

Livarno IAN 373572 Bedienungsanleitung

17 September 2024
Autel

Autel MaxiScan MS309 Bedienungsanleitung

17 September 2024
IFM

IFM KG0009 Bedienungsanleitung

17 September 2024
LG

LG PL-F860 Bedienungsanleitung

17 September 2024
Crivit

Crivit IAN 302540 Bedienungsanleitung

17 September 2024
IFM

IFM AC2451 Bedienungsanleitung

17 September 2024
Aqua Joe

Aqua Joe AJYP100 Bedienungsanleitung

17 September 2024
Texas Instruments

Texas Instruments SN74LV125APWR Bedienungsanleitung

17 September 2024