Dormakaba RCI 8310 Bedienungsanleitung

Dormakaba Nicht kategorisiert RCI 8310

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dormakaba RCI 8310 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

INSTALLATION

RCI 8310 / 8320

ELECTROMAGNETIC LOCKS

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

IS8310-20-V1-2

PCN19025

R07-20GR-1

1. Mount the electromagnetic lock to the door frame as outlined on

the installation template included with the product.

NOTE: During installation of the armature plate to the door it

is essential that the armature plate remains movable. The

armature plate must be allowed to pivot on the center-mounting

bolt to allow proper alignment with the magnet surface. If the

plate is not aligned with the magnet surface, the lock may lose

holding force or not lock at all .

The head of the armature mounting bolt ships with a rubber

washer affixed to it. This washer should project slightly beyond

the surface of the armature plate. This is to allow the washer to

expand when power is removed and break the air vacuum

between the plate and the magnet surface. If this washer is

removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided for

the armature plate bolt and the four captive electromagnetic lock

mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware

to disengage and fall, causing serious bodily injury and property

damage. dormakaba Canada Inc. and/or dormakaba USA Inc. will

not be liable to the installer, purchaser, end user or anyone else for

damage or injury to person or property due to improper installation,

care, storage, handling, maintenance, inspection, abuse, misuse

or act of God or nature involving this product or any related

accessories or parts.

2. Route the power supply connecting wire through the door frame

and into the wire access hole in the top of the magnet housing.

Connecting wire should be of sufficient gauge for the lock being

installed and the distance being run.

Installation Instructions

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Pre-Installation Instructions

1. This product must be installed according to all applicable building

and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally sound

prior to installation of the electromagnetic lock. The structural

integrity of the mounting surfaces must be strong enough to meet

or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of applications

and different door frame configurations, an experienced installer

with knowledge of this product must make a determination of the

optimal mounting method for this specific application.

7. The components, hardware, installation instructions and mounting

template included with this product are intended for use on

outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories, must be used in the following applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that do not have a door frame

• Hollow metal or wood frames where the door stop is

not thick enough to allow the product to be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the page 5 & 6 Product Accessories Guide, for further

information. Accessories may impact holding force.

11. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound

be applied to all screws during installation to reduce chance of

screws loosening over extended time.

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

3. Once wiring has been routed into the lock cavity, connect wire to

terminal blocks as shown in Fig. 1. If optional SCS and/or DSS

features are being used these can also be wired at this time as

shown in Fig. 1.

4. Delayed Relock Feature - Should the built-in delayed relock feature be

required for the installation, a Normally Open Momentary switch such

as an RCI 909 will need to be installed and connected to the two blue

wires from on the circuit board as illustrated in Fig.1. EXIT

The delayed relock feature can be used to momentarily release the

lock and keep it unlocked for a time period from 0 to approximately

35 seconds. The time delay for this feature can be adjusted by

carefully turning the potentiometer (R ) in a counterclockwise W1

direction to increase delay time. Factory setting is zero seconds.

NOTE: On the 8320 double-door model turn bothRCI

potentiometers counterclockwise to increase the relock delay.

If the delayed relock feature is not required the blue wires may be

unplugged from the circuit board @ EXIT.

W1NOTE: If R is not set to zero seconds, the lock will enter

delayed relock mode each time power is applied even if EXIT has

been removed.

To Ensure Instant Release - All switching devices must be wired in

between the DC power source and the positive terminal of the lock in

Fig 2.

Switching the negative power supply line will not allow the lock to

release immediately. RCI electromagnetic locks contain MOV’s for

surge suppression and do not require any additional suppression to be

added during installation. The installation of diodes across the lock input

terminals will cause a delay in release.

Fig. 2 – Power Connections

SWITCH

INCORRECT

CORRECT

SWITCH

FILTERED DC SUPPLY

Fig.1 – Lock Wiring

Delayed Relock Adjustmen RW1t

Turn counterclockwise o incr se delay t ea

on 8310 single and both sides of the 8320

double door model.

Lo Power from ack

f ter r lated DCil ed and egu

power su lypp

Opti al SCS nsoron Se

SPDT Out c tacts ratedput on

for maximum 1A @2 DC4V

EXIT EXIT

Two 8 Loc o rel se o ther using310 ks t ea t ge

t lay relock ture.he de ed fea

Blue Wires

Momentary Switch

Bo de 832 Loth si s o an f 0 ck to release together

usi he lay relock f ture.ng t de ed ea

Le circuit boardft Right circui boardt

Optional Del d Relock W ngaye iri

Single lock o release using t

t lay relock ture.he de ed fea

RED - No a y Closedrm ll

GREEN - Normally O npe

BLACK - Common

Opti l DSS r s tch c tacts rat atona eed wi on ed

0.20A@ DC a 0.12A @ 2 DC12V nd 4V

Blue/White

Wires

Blue Wires

Blue/White

Wires

EXIT EXIT

Momentary Switch

N/O

EXIT

Momentary Switch

Blue Wires

Blue/White

Wires

N/O

Blue Wires

Blue/White

Wires

Blue Wires

Blue/White

Wires

EXIT

8310 V1.2 PCB

MAG

Common

No ally Closedrm

No ally Openrm

Comm Gro don un

VDC Input

Both the SCS and DSS options are shown with Door Open

SCS1 LED

* NOTE: Models with SCS ship with the low voltage

detection circuit ENABLED (jumper LP_EN on 1 pin only).

To DISABLE low voltage detection, place jumper on both

pins of LP_EN.

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

Anti-Tamper Feature - Two screws prevent insertion of an Allen

wrench into the captive mounting screw opening on the bottom of

the lock. Fig. 3 shows their location. One screw also secures the

wiring cavity cover. The mounting plate cannot be separated from

the lock without removing these two screws.

Lock Options

Both of the RCI 8310 and 8320 locks can be equipped with the DSS or SCS

options or both.

SCS (Security Condition Sensor) - This feature can detect the quality of the

locking bond between the surface of the magnet and the armature plate.

Indication is with a local LED as well as remote monitoring through a SPDT

relay output. The sensitivity of this feature is such that a foreign object with

a thickness of .007” (.18mm) is sufficient to allow the sensor to detect a

problem.

Due to the sensitivity of this feature and the necessity to maintain a reliable

locking bond, these surfaces must be kept free of contaminating materials.

Both the lock surface and the armature plate must be cleaned periodically

with a non-abrasive cleanser. Alignment of armature plate and magnet is

required to ensure proper function of sensor.

Low Voltage Detection - Each SCS circuit board also includes a low voltage

detection circuit when shipped from the factory. This feature will cause the

alarm relay and status LED to activate should the lock input voltage drop

below 9VDC. That signals a monitored system or guard station that the

holding force of the lock may have been compromised.

Models with Security Condition Sensor (SCS) have the Low Voltage

Detection circuit when shipped (jumper LP_EN on 1 pin only) ENABLED

To DISABLE Low Voltage Detection, place jumper on both pins of LP_EN.

DSS (Door Status Sensor) - The DSS option monitors the position of the door

upon which the lock is installed. A SPDT reed switch mounted within the lock

cavity eliminates the need for extra sensors to be installed on the door for

notification of security or access control systems. The DSS option comes

with a magnet pre-installed into the lock armature plate for signaling the reed

switch in the housing when the door is closed independent of power to the

lock. Care should be taken during the final testing of the lock to ensure that

the DSS option is operating in the desired manner.

Inspection and Maintenance

This product and all related accessories or parts must be inspected

and maintained on a . Contacting surfaces of the quarterly basis

electromagnetic lock and armature plate must be kept free of contaminating

materials. Surfaces must be cleaned periodically with a non-abrasive cleaner.

All mounting fasteners must be inspected on a . When quarterly basis

properly installed, the ends of the armature plate allow a slight movement

but the plate will feel secure when grasped at the bolt. There should be no

movement to the mounting bracket or housing of the electromagnetic lock.

For added safety, thread locking compound has been provided for the

armature plate bolt and the four captive electromagnetic lock mounting

screws.

WARNING: Improper installation, maintenance, inspection or usage of the

product or any related accessories or parts may cause the electromagnetic

lock, armature plate and associated hardware to disengage and fall,

causing serious bodily injury and property damage.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO THE

END-USER UPON COMPLETION OF THE INSTALLATION.

Fig. 3 – Lock Mounting

Anti-tamper

feature screw Anti-tamper

feature and

wiring cavity

screw

Captive

mounting screw

Listings

These products have been successfully tested and evaluated by UL in two

separate categories for use in both the United States and Canada.

Auxiliary Lock. The GWXT fire listing qualifies these for use with UL

Classified fire doors maximum 4’ in width and 8’ in height. The

RCI 8310 and 8320 are rated up to and including 1-1/2 hours

(90 minutes).

Special Locking Arrangement Component. Additionally, these products are

qualified components for the purpose of locking outward-

swinging exit doors against unauthorized egress.They are

designed to release automatically in case of a power failure or

upon activation of an automatic fire alarm system wired to the power

supply fire panel relay.

The Following Conditions of Acceptability Apply:

1) This product is intended for use with Special Locking Arrangements

which are installed in accordance with the manufacturer’s installation and

operation instructions, the Life Safety Code, NFPA 101 of the National Fire

Protection Association and the local authority having jurisdiction.

2) The power for this unit is to be provided by a Listed (ALVY, FULA,

or APHV) Class 2 power supply when designated as a Special Locking

Arrangement (FWAX).

3) The suitability of the lead wires is to be evaluated per the requirements

for the end-use product.

4) If the product is installed in conjunction with a fire alarm control panel,

the wiring from the control unit to this product device shall be for fail-safe

operation.

UL testing was conducted on standard models without accessories. These

locks are not intended or tested for use as a UL Listed Burglar Alarm

System Unit.

Produktspezifikationen

Marke:	Dormakaba
Kategorie:	Nicht kategorisiert
Modell:	RCI 8310

Brauchst du Hilfe?

Wenn Sie Hilfe mit Dormakaba RCI 8310 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Dormakaba

Dormakaba Keyscan EC1500 Bedienungsanleitung

22 August 2024

Dormakaba EAC Bedienungsanleitung

22 August 2024

Dormakaba DKX Type III Bedienungsanleitung

22 August 2024

Dormakaba HSW-GP Bedienungsanleitung

21 August 2024

Dormakaba DKX-10 Bedienungsanleitung

21 August 2024

Dormakaba Confidant RFID Kit 1 Bedienungsanleitung

21 August 2024

Dormakaba DKX Type IV Bedienungsanleitung

21 August 2024

Dormakaba Keyscan Aurora Bedienungsanleitung

21 August 2024

Dormakaba HSB-M01 Bedienungsanleitung

21 August 2024

Dormakaba DKPS-4A Bedienungsanleitung

21 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024