DeWalt DW616D Bedienungsanleitung

DeWalt Router DW616D

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für DeWalt DW616D (17 Seiten) in der Kategorie Router. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/17
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DW616/DW618
Router System
Système de toupie
Sistema de rebajadora
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ASE ESTE INSTRUCTIVOADVERTENCIA:
ANTES DE USAR EL PRODUCTO.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(MAR05) Form No. 631103-00 DW616, DW618 Copyright © 2003, 2005 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped
air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps
on the surface of the tool.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS, OR ANY D
E
WALT TOOL,
CALL US TOLL FREE AT 1-800-4-D
E
WALT (1-800-433-9258).
SAVE THESE INSTRUCTIONS
General Safety Instructions
WARNING! Read and understand all instructions. Failure to follow all instruc-
tions listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Safety Instructions For All Tools
WORK AREA
Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-
dents.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust
or fumes.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
Grounded tools must be plugged into an outlet properly installed and grounded in
accordance with all codes and ordinances. Never remove the grounding prong or
modify the plug in any way. Do not use any adapter plugs. Check with a qualified
electrician if you are in doubt as to whether the outlet is properly grounded. If the
tool should electrically malfunction or break down, grounding provides a low resistance
path to carry electricity away from the user. This tool uses grounded construction (3 prong
plug) to provide a means to transfer electrical energy safely away from the user in the event
the tool electrically malfunctions, breaks down, or the tool case becomes live. Damage to, or
loss of, one of the 3 plug blades; damage to the plug or cord, or failure to have the tool
plugged into a verified and continuously grounded electrical system, may result in electric
shock, serious injury, or death. To avoid these risks of injury, the tool must, at all times, be
maintained and in proper working order (cord, plug blades) and plugged into a continuously
grounded electrical system. (See also “Cleaning” in the Maintenance section.)
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace dam-
aged cords immediately. Damaged cords increase the risk of electric shock.
When operating a power tool outside, use an outdoor extension cord marked “W-A”
or “W.” These cords are rated for outdoor use and reduce the risk of electric shock.
EXTENSION CORDS
Make sure your extension cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your product will draw. A volt-
age decrease of more than 10% will cause a loss of power and overheating
.
An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating. The fol-
lowing table shows the correct size to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the
cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing , and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts. Air vents often cover moving parts and should also be avoided.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying
tools with your finger on the switch or plugging in tools that have the switch on invites
accidents.
Remove adjusting keys or wrenches before turning the tool on. A wrench or key that
is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
Use clamps or other practical ways to secure and support the workpiece to a sta-
ble platform. Holding the work by hand or against your body is unstable and may lead
to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool will do
the job better and safer and the rate for which it is designed.
Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. Such preventative safety measures reduce
the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons. Tools are dan-
gerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tools operation. If damaged, have the tool serv-
iced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
SERVICE
Tool service must be performed only by qualified repair personnel. Service or main-
tenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow main-
tenance instructions may create a risk of electric shock or injury.
Specific Safety Rules for Routers
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live” and shock the operator.
Metal cutting with router: If using router for metal cutting, clean out tool often. Metal dust
and chips often accumulate on interior surfaces and could create a risk of serious injury,
electrical shock or death.
Never run the motor unit when it is not inserted in one of the router bases. The motor
is not designed to be handheld.
Keep handles dry, clean, and free from oil and grease. This will enable better control of
the tool.
Keep hands away from cutting area. Never reach under the workpiece for any reason.
Keep the router base firmly in contact with the workpiece when cutting. Hold the
router only by the handles. These precautions will reduce the risk of personal injury.
Use sharp cutters. Dull cutters may cause the router to swerve or stall under pressure.
Never touch the bit immediately after use. It may be extremely hot.
Be sure that the motor has stopped completely before you lay the router down. If the
cutter head is still spinning when the tool is laid down, it could cause injury or damage.
Be sure that the router bit is clear of the workpiece before starting the motor. If the bit
is in contact with the workpiece when the motor starts it could make the router jump, caus-
ing damage or injury.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and
duration of use, noise from this product may contribute to hearing loss.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:
lead from lead-based paint.
crystalline silica from bricks and cement and other masonry products.
arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory pro-
tection appropriate for the dust exposure. Direct particles away from face and body.
The label on your tool may include the following symbols. The symbols and definitions are
as follows:
V ............volts ........alternating current
A ............amperes ......direct current
Hz ..........hertz no..........no load speed
W ............watts ..........Class II Construction
min..........minutes ..........earthing terminal
..........safety alert symbol …/min ..revolutions per minute
FAMILIARIZATION
Motor
Your DEWALT tool is powered by a DEWALT-built motor. Be sure your power supply agrees
with the nameplate marking.
“120 V~” means your tool may be operated with alternating current only. Do not connect your
tool to a direct current power supply. All DEWALT tools are factory tested; if this tool does not
operate, check the power supply.
Switch
To turn the tool on, push the toggle switch to the on position indicated on the tool. To turn the
tool off, push the toggle switch to the off position indicated on the tool.
Detachable Cord Set (Fig. 1)
Insert the detachable cordset plug so that the key (W) is aligned with the notch (V) in the
socket. Turn the plug clockwise one quarter turn to lock.
CAUTION: Always turn off the tool and remove the plug from the power supply before
detaching the cordset from the tool.
CAUTION: Always leave the toggle switch in the off position when removing or attaching
the cord from the motor. If the toggle switch is in the on position when the cordset is attached,
the tool will start unexpectedly, causing loss of control, personal injury, and/or damage to the
tool or workpiece.
SET-UP: FIXED BASE
Motor Quick Release (Fig. 2)
CAUTION: Turn the router off and disconnect it from the power supply.
1. Open the locking lever (D) on the base.
2. Grasp the base with one hand, depressing the quick release latches (A).
3. With the other hand, grasp the top of the motor unit and lift it from the base.
Inserting the Motor into the Fixed Base (Fig. 3)
CAUTION: Turn the router off and disconnect it from the power supply.
1. Open the locking lever (D) on the base.
2. If the depth adjustment ring (B) is not on the motor, thread the depth adjustment ring (B)
onto the motor until the ring is about halfway between the top and bottom of the motor as
shown. Insert the motor into the base by aligning the groove on the motor (H) with the
guide pins (X) on the base. Slide the motor down until the Depth Adjustment Ring snaps
into the quick release latches (A).
NOTE: Guide pin grooves are located on either side of the motor so that it can be positioned
in two orientations.
3. Adjust the depth of cut by turning the depth adjustment ring. See the heading Adjusting the
Depth of Cut OPERATION: FIXED BASE in the section of this manual.
4. Close the locking lever (D) when the desired depth is achieved. For information on set-
ting the cutting depth, see the heading in the Adjusting the Depth of Cut OPERATION:
FIXED BASE section of this manual.
Locking Lever Adjustment (Fig. 4)
CAUTION: Turn the router off and disconnect it from the power supply.
You should be able to clamp the locking lever without excessive force. Excessive force may
damage the base.
You should not be able to move the motor in the base when the locking lever is clamped. To
adjust the locking lever’s clamping force, open the locking lever (D) and turn the nut (Y) in
small increments. Turning the nut clockwise tightens the lever, while turning the nut counter-
clockwise loosens the lever.
Centering the Subbase (Fig. 5)
CAUTION: Turn the router off and disconnect it from the power supply.
If you need to adjust, change, or replace the subbase, a centering tool is provided. The cen-
tering tool consists of a cone and a pin. To adjust the subbase, follow the steps below.
1. Loosen but do not remove the subbase screws so that the subbase can move freely.
2. Insert the pin into the collet and tighten the collet nut.
3. Insert the motor into the base and clamp the locking lever on the base.
4. Place the cone on the pin and lightly press down on the cone until it stops as shown. This
will center the subbase.
5. While holding down on the cone, tighten the subbase screws.
OPERATION: FIXED BASE
Bit Installation and Removal (Fig. 6)
CAUTION: Turn the router off and disconnect it from the power supply.
1. To install a bit, insert the round shank of the desired router bit into the loosened collet as
far as it will go and then pull it out about 1/16". Using the wrench(es) provided, turn the col-
let nut (J) clockwise while holding the spindle shaft with the second wrench. [On the
DW618, depress the spindle lock button (I) to hold the spindle shaft.]
2. To remove a bit, hold the spindle shaft while turning the collet nut (J) counterclockwise
with the wrench provided. [Hold the spindle by depressing the spindle lock button (I) on
the DW618.] The self-releasing collet nut will turn approximately 3/4 of a turn and then
become tight again. At this point the bit cannot be removed. Continue turning the collet
nut counterclockwise. This lifts the collet, allowing the bit’s removal.
Collets
NOTE: Never tighten the collet without first installing a router bit in it. Tightening an empty col-
let, even by hand, can damage the collet.
Two collets are included with the motor: one 1/4" and one 1/2". To change collet sizes,
unscrew the collet assembly as described above. Install the desired collet by reversing the
procedure. The collet and the collet nut are connected. Do not attempt to remove the collet
from the collet nut.
Adjusting the Depth of Cut (Fig. 2, 3)
CAUTION: Turn the router off and disconnect it from the power supply.
1. Select and install the desired bit. See the heading Bit Installation and Removal.
2. Place the router on its base on the work piece.
3. Open the locking lever (D) and turn the depth adjustment ring (B) until the bit just touches
the work piece. Turning the ring clockwise raises the cutting head while turning it counter-
clockwise lowers the cutting head.
4. Move the adjustable scale clockwise (C) so that 0 on the scale is located exactly above
the pointer (Z) on the base.
5. Turn the depth adjustment ring along with the adjustable scale to the desired depth. Note
that each mark on the adjustable scale represents a depth change of 1/64" or .015"
(.4mm).
6. Close the locking lever (D).
Using a Parallel Fence
A parallel fence (DW6913) is available from your local retailer or service center at extra cost.
Follow the assembly instructions included with the fence. Insert the two bars through the edge
guide holes in the router base. Adjust as needed for parallel routing.
SET-UP: D-HANDLE BASE
Motor Quick Release
CAUTION: Turn the router off and disconnect it from the power supply.
1. Open the locking lever (D) on the base.
2. Grasp the base with one hand while depressing the quick release latches (A).
3. With the other hand, grasp the top of the motor unit and lift it from the base.
Inserting the Motor into the D-Handle Base (Fig. 7)
CAUTION: Turn the router off and disconnect it from the power supply.
1. Open the locking lever (D) on the base.
2. Thread the depth adjustment ring (B) onto the motor until the ring is about halfway between
the top and bottom of the motor. Insert the motor into the base by aligning the groove on
the motor (H) with the guide pins (X) on the base. Slide the motor down until the depth
adjustment ring snaps into the quick release latches (A).
3. Close the locking lever when the desired depth is achieved. For information on setting cut-
ting depth, see the heading Adjusting the Depth of Cut in the OPERATION: D-HANDLE
BASE section of this manual.
4. Be sure that the trigger switch (N) is released and the trigger lock button (O) is in the
unlocked and off position.
5. Unlock and disconnect the detachable cordset (L) from the motor.
6. Connect the detachable cordset (L) to bottom of D-Handle and lock the cord.
7. Connect the short cord (AA) from top of D-Handle to the motor as shown. Be sure the cord
is locked.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-DEWALT • www.dewalt.com
8. Place the toggle switch in the on position. This allows the trigger switch on the D-handle
to control the router.
Locking Lever Adjustment (Fig. 4)
CAUTION: Turn the router off and disconnect it from the power supply.
You should be able to clamp the locking lever without excessive force. Excessive force may
damage the base.
You should not be able to move the motor in the base when the locking lever is clamped. To
adjust the locking lever’s clamping force, open the locking lever (D) and turn the nut (Y) in
small increments. Turning the nut clockwise tightens the lever while turning the nut counter-
clockwise loosens the lever.
Centering the Subbase (Fig. 5)
CAUTION: Turn the router off and disconnect it from the power supply.
If you need to adjust, change, or replace the subbase, a centering tool is provided. The cen-
tering tool consists of a cone and a pin. To adjust the subbase, follow the steps below.
1. Loosen but do not remove the subbase screws so that the subbase can move freely.
2. Insert the pin into the collet and tighten the collet nut.
3. Insert the motor into the base and clamp the locking lever on the base.
4. Place the cone on the pin and lightly press down on cone until it stops as shown. This will
center the subbase.
5. While holding down on the cone, tighten the subbase screws.
OPERATION: D-HANDLE BASE
Knob Locations
Grip the D-Handle with one hand and place the other hand on the the knob. The D-Handle
router base has two positions for the knob to accommodate right or left hand use.
CAUTION: Use both hands at all times to maintain control.
Trigger Lock
To lock the trigger, pull the trigger switch (N) completely, then push the trigger lock button (O).
The router will remain on after you remove your finger from the trigger. To unlock the trigger lock
button, pull the trigger and release. The lock button will pop out and the router will turn off.
Bit Installation and Removal (Fig. 6)
CAUTION: Turn the router off and disconnect it from the power supply.
1. To install a bit, insert the round shank of the desired router bit into the loosened collet as far
as it will go and then pull it out about 1/16". Using the wrench(es) provided, turn the collet
nut (J) clockwise while holding the spindle shaft with the second wrench. [On the DW618,
depress the spindle lock button (I) to hold the spindle shaft.]
2. To remove a bit, hold the spindle shaft while turning the collet nut (J) counterclockwise with
the wrench provided. [Hold the spindle by depressing the spindle lock button (I) on the
DW618.] The self-releasing collet nut will turn approximately 3/4 of a turn and then become
tight again. At this point the bit cannot be removed. Continue turning the collet nut counter-
clockwise. This lifts the collet, allowing the bit’s removal.
Collets
NOTE: Never tighten the collet without first installing a router bit in it. Tightening an empty col-
let, even by hand, can damage the collet.
Two collets are included with the motor: one 1/4" and one 1/2". To change collet sizes, unscrew
the collet assembly as described above. Install the desired collet by reversing the
procedure.The collet and the collet nut are connected. Do not attempt to remove the collet from
the collet nut.
Adjusting the Depth of Cut (Fig. 3)
CAUTION: Turn the router off and disconnect it from the power supply.
1. Select and install the desired bit. See the heading Bit Installation and Removal.
2. Place the router on its base on the work piece.
3. Open the locking lever (D) and turn the depth adjustment ring (B) until the bit just touches
the work piece. Turning the ring clockwise raises the cutting head while turning it counter-
clockwise lowers the cutting head.
4. Move the adjustable scale clockwise so that 0 on the scale is located exactly above the
pointer (Z) on the base.
5. Turn the depth adjustment ring along with the adjustable scale to the desired depth. Note
that each mark on the adjustable scale represents a depth change of 1/64" or .015"
(.4mm).
6. Close the locking lever (D).
Using a Parallel Fence
A parallel fence (DW6913) is available from your local retailer or service center at extra cost.
Follow the assembly instructions included with the fence. Insert the two bars through the holes
in the router base. Adjust as needed for parallel routing.
SET-UP: PLUNGE BASE (Fig. 8)
Motor Quick Release
CAUTION: Turn the router off and disconnect it from the power supply.
1. Open the locking lever (D) on the base.
2. Grasp the top of the motor unit and lift it from the base.
Inserting the Motor into the Plunge Base
CAUTION: Turn the router off and disconnect it from the power supply.
1. Remove the depth adjustment ring from the motor. It is not used with the plunge base.
2. Open the locking lever (D) on the base to ensure that the motor properly seats.
3. Ensure that the plunge lock lever (R) is locked.
4. Align the flat of the motor’s end cap (BB) with pillar (CC) and insert the motor into the
plunge base until it stops.
5. Close the locking lever (D).
Locking Lever Adjustment (Fig. 4)
CAUTION: Turn the router off and disconnect it from the power supply.
You should be able to clamp the locking lever without excessive force. Excessive force may
damage the base.
You should not be able to move the motor in the base when the locking lever is clamped.
To adjust the locking lever’s clamping force, open the locking lever (D) and turn the nut
(Y) in small increments. Turning the nut clockwise tightens the lever, while turning the nut
counterclockwise loosens the lever.
Centering the Subbase (Fig. 5)
CAUTION: Turn the router off and disconnect it from the power supply.
If you need to adjust, change, or replace the subbase, a centering tool is provided. The
centering tool consists of a cone and a pin. To adjust the subbase, follow the steps below.
1. Loosen but do not remove the subbase screws so that the subbase can move freely.
2. Insert the pin into the collet and tighten the collet nut.
3. Insert the motor into the base and clamp the locking lever on the base.
4. Place the cone on the pin and lightly press down on the cone until it stops as shown. This
will center the subbase.
5. While holding down on the cone, tighten the subbase screws.
OPERATION: PLUNGE BASE
Bit Installation and Removal (Fig. 6)
CAUTION: Turn the router off and disconnect it from the power supply.
1. To install a bit, insert the round shank of the desired router bit into the loosened collet as
far as it will go and then pull it out about 1/16". Using the wrench(es) provided, turn the col-
let nut (J) clockwise while holding the spindle shaft with the second wrench. [On the
DW618, depress the spindle lock button (I) to hold the spindle shaft.]
2. To remove a bit, hold the spindle shaft while turning the collet nut (J) counterclockwise
with the wrench provided. [Hold the spindle by depressing the spindle lock button (I) on
the DW618.] The self-releasing collet nut will turn approximately 3/4 of a turn and then
become tight again. At this point the bit cannot be removed. Continue turning the collet
nut counterclockwise. This lifts the collet, allowing the bit’s removal.
Collets
NOTE: Never tighten the collet without first installing a router bit in it. Tightening an empty col-
let, even by hand, can damage the collet.
Two collets are included with the motor: one 1/4" and one 1/2". To change collet sizes, unscrew
the collet assembly as described above. Install the desired collet by reversing the
procedure.The collet and the collet nut are connected. Do not attempt to remove the collet from
the collet nut.
Adjusting the Plunge Routing Depth (Fig. 8)
CAUTION: Turn the router off and disconnect it from the power supply.
1. Unlock the plunge mechanism by pushing up the plunge lock lever (R). Plunge the router
down as far as it will go, allowing the bit to just touch the workpiece.
2. Lock the plunge mechanism by pushing the plunge lock lever (R) down.
3. Loosen the depth adjustment rod (Q) by turning the wingscrew (DD) counterclockwise.
4. Slide the depth adjustment rod (Q) down so that it meets the lowest turret stop (P).
5. Slide the tab (EE) on the depth adjustment rod down so that the top of it meets zero on the
pillar scale (FF).
6. Grasping the top, knurled section of the depth adjustment rod (Q), slide it up so that the
tab (EE) aligns with the desired depth of cut on the pillar scale (FF).
7. Tighten the wingscrew (DD) to hold the depth adjustment rod in place.
8. Keeping both hands on the handles, unlock the plunge mechanism by pushing the plunge
lock lever (R) up. The plunge mechanism and the motor will move up. When the router is
plunged, the depth adjustment rod will hit the turet stop, allowing the router to reach exact-
ly the desired depth.
Fine Adjustment of Routing Depth
CAUTION: Turn the router off and disconnect it from the power supply.
The knurled knob (GG) at the bottom end of the depth adjustment rod can be used to make
minor adjustments.
1. To decrease the cutting depth, rotate the knob clockwise (looking down from the top of the
router).
2. To increase the cutting depth, rotate the knob counterclockwise (looking down from the top
of the router).
NOTE: One complete rotation of the knob results in a change of about 5/128" or .04" (1 mm)
in depth.
Using the Rotating Turret Stop (Fig. 9)
The turret depth stop can be used to set 5 different depths. One of the turret stops is adjustable.
To use the adjustable turret stop, loosen the nut (HH), then adjust the screw (II) to the desired
height. Turning the screw counterclockwise will raise the screw which will decrease the cutting
depth. The turret stop is useful for making deep cuts in several passes.
WARNING: Do not change the turret stop while the router is running. This will place your
hands too near the cutter head.
Cutting with the Plunge Base (Fig. 8)
CAUTION: Turn the router on before plunging the cutter head into the workpiece.
1. Unlock the plunge lock lever (R).
2. Plunge the router down until the bit reaches the set depth.
3. Lock the plunge lock lever (R).
4. Perform the cut.
5. Unlock the plunge lock lever. This will allow the router bit to disengage the work.
6. Turn the router off.
Dust Extraction (Fig. 10)
CAUTION: Turn the router off and disconnect it from the power supply.
To connect the router to a vacuum cleaner for dust extraction, follow these steps:
1. Remove the dust cap (T) by pulling straight up.
2. Insert the dust extraction hose adapter (JJ) into the dust extraction port (KK) as shown.
3. Insert the end of a standard vacuum cleaner tube (LL) into the hose adapter.
4. When using dust extraction, be aware of the placement of the vacuum cleaner. Be sure that
the vacuum cleaner is stable and that its hose will not interfere with the work.
OPERATION: ALL BASES
Direction Of Feed (Fig. 11)
The direction of feed is very important when routing and can make the difference between a
successful job and a ruined project. The figures at left show the proper direction of feed for
some typical cuts. A general rule to follow is to move the router in a counterclockwise direction
on an outside cut and a clockwise direction on an inside cut.
Shape the outside edge of a piece of stock by following these steps:
1. Shape the end grain, left to right
2. Shape the straight grain side moving left to right
3. Cut the other end grain side
4. Finish the remaining straight grain edge
Choosing Router Speed (DW618 only) (Fig. 12)
Refer to the chart above to choose a router speed. Turn the speed dial (G) to control router
speed.
MAINTENANCE
Cleaning
WARNING: Blowing dust and chips out of the motor housing using clean, dry compressed
air is a necessary regular maintenance procedure. Dust and chips containing metal particles
often accumulate on interior surfaces and could create an electrical shock or electrocution if
not frequently cleaned out. ALWAYS WEAR SAFETY GLASSES.
CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. Use a clean, dry rag only.
NOTE FOR PLUNGE BASE ONLY: Use only a DRY cloth to wipe the plunge rods. These
rods require no lubrication. Lubricants attract dust, reducing the performance of your tool.
Accessories
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory for your
tool, call us toll free at: 1-800-4-DEWALT (1-800-433-9258) or contact DEWALT Industrial Tool
Co., 701 East Joppa Road, Baltimore, MD 21286.
CAUTION: The use of any other accessory not recommended for use with this tool could
be hazardous.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (includ-
ing brush inspection and replacement) should be performed by authorized service centers or
other qualified service personnel, always using identical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply
to accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser,
or Nailer for any reason, you can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.
RECONDITIONED PRODUCT: Reconditioned product is covered under the 1 Year Free
Service Warranty. The 90 Day Money Back Guarantee and the Three Year Limited Warranty
do not apply to reconditioned product.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.
SI VOUS AVEZ DES QUESTIONS OU VOUS VOULEZ NOUS FAIRE PART DE VOS COM-
MENTAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL DEWALT, COMPOSEZ
SANS FRAIS LE 1 800 433-9258.
CONSERVER CES DIRECTIVES!
MESURES DE SÉCURITÉ – GÉNÉRALITÉS
AVERTISSEMENT! Lire et comprendre toutes les directives, car le non-
respect des directives suivantes pourrait entraîner un risque de choc élec-
trique, d’incendie ou de blessures graves.
CONSERVER CES DIRECTIVES
Consignes de sécurité concernant tous les outils
ZONE DE TRAVAIL
Garder la zone de travail propre et bien éclairée; les établis encombrés et les endroits
sombres sont propices aux accidents.
Ne pas utiliser les outils électriques dans une atmosphère explosive, comme à
proximité de liquides, de gaz ou de poussières inflammables; le moteur peut créer
des étincelles et enflammer les vapeurs ou les poussières environnantes.
Tenir les enfants, les visiteurs ou toute autre personne à l’écart lorsqu’on utilise un
outil électrique; les distractions peuvent faire perdre la maîtrise de ce dernier.
MESURES DE SÉCURITÉ - ÉLECTRICITÉ
Les outils mis à la terre doivent être branchés dans une prise bien installée et mise
à la terre conformément à tous les codes et règlements en vigueur. Ne jamais retir-
er la broche de terre ni modifier la fiche. Ne pas utiliser d'adaptateur. Vérifier auprès
d'un électricien qualifié en cas de doute quant à la mise à la terre de la prise. En cas
de défaillance électrique ou de bris de l'outil, la mise à la terre procure un chemin de faible
résistance au courant qui autrement traverserait l'utilisateur. Pour éviter que l’utilisateur ne
soit électrocuté en cas de défaillance, de bris ou de conductivité de l’outil, celui-ci est do
d’une fiche à trois broches afin d’assurer la mise à la terre. Il y a risque d’électrocution, de
blessures graves ou de mort lorsqu’on utilise un outil dont une broche est endommagée ou
absente ou dont la fiche ou le cordon est endommagé ou qui n’est pas branché dans une
prise conforme mise continuellement à la terre. Pour éviter les risques de blessures, l’outil
doit toujours être bien entretenu et en bon état de marche (cordon, broches de la fiche)
et doit être branché dans une prise mise à la terre continuellement. (Voir également la
rubrique « Nettoyage » dans la section Entretien.)
Éviter tout contact entre le corps et les éléments mis à la terre, comme les tuyaux,
les radiateurs, les cuisinières et les réfrigérateurs, afin de réduire les risques de choc
électrique.
Ne pas utiliser l’outil électrique dans des endroits mouillés, ni l’exposer à la pluie;
l’infiltration d’eau à l’intérieur de l’outil augmente les risques de choc électrique.
Ne pas utiliser le cordon de manière abusive; on ne doit pas transporter l’outil en le
tenant par le cordon, ou utiliser ce dernier pour le débrancher. On doit tenir le cor-
don à l’écart des sources de chaleur, de l’huile, des bords tranchants ou des pièces
mobiles. Remplacer immédiatement les cordons endommagés, car ces derniers aug-
mentent les risques de choc électrique.
Lorsqu’on utilise un outil électrique à l’extérieur, on ne doit utiliser que des ral-
longes conçues pour cet usage, comme celles de type
«
W-A
»
ou
«
W
»
,afin de
réduire les risques de choc électrique.
RALLONGES
S’assurer que la rallonge est en bon état; si on utilise une rallonge, s’assurer d’en
choisir une qui est en mesure de porter le courant nécessaire à l’outil. Une baisse
de tension de plus de 10 p. 100 peut entraîner une perte de puissance et la surchauffe.
Une rallonge de calibre inférieur entraînera une chute de tension se traduisant par une
perte de puissance et une surchauffe. Le tableau ci-dessous illustre les calibres que l’on
doit utiliser selon la longueur de la rallonge et l’intensinominale indiquée sur la plaque
signalétique. En cas de doute, utiliser le calibre suivant. Plus le calibre est petit, plus la ral-
longe peut porter de courant.
Calibre minimal des cordons de rallonge
TensionLongueur totale du cordon en meters
120 V De 0 à 7 De 7 à 15 De 15 à 30 De 30 à 45
240 V De 0 à 7 De 7 à 15 De 15 à 39 De 30 à 45
Intensité (A)
Au Au Calibre moyen de fil
moins plus
10 - 12 16 16 14 12
12 - 16 14 12 Non recomman
SÉCURITÉ PERSONNELLE
Rester vigilant en tout temps et faire preuve de jugement lorsqu’on utilise un outil
électrique; ne pas utiliser l’outil lorsqu’on est fatig ou sous l’influence de drogues,
d’alcool ou de médicaments, car un moment d’inattention pourrait entraîner des blessures
graves.
Porter des tements appropriés; ne pas porter de tements amples ni de bijoux.
Couvrir ou attacher les cheveux longs. Garder les cheveux, les vêtements, les bijoux
et les gants éloigs des pièces mobiles, car ceux-ci peuvent s’y coincer. Se tenir éloigné
des évents puisque ces derniers pourraient camoufler des pièces mobiles.
Éviter les démarrages accidentels; s’assurer que l’interrupteur est en position d’ar-
t avant de brancher l’outil. Ne pas transporter l’outil en laissant le doigt sur l’interrup-
teur ni le brancher lorsque l’interrupteur est en position de marche, car cela pourrait causer
un accident.
Retirer les clés de réglage avant de marrer l’outil; une clé laissée sur une pièce rota-
tive peut entraîner des blessures.
Ne pas trop étendre les bras; les pieds doivent rester ancs fermement au sol afin
de maintenir son équilibre en tout temps et de mieux maîtriser l’outil dans des situa-
tions imprévues.
Utiliser le matériel de curité approprié; toujours porter des lunettes de protection.
Porter un masque anti-poussières, des chaussures antidérapantes, un casque de sécuri
ou des protecteurs auditifs lorsque la situation le requiert.
UTILISATION ET ENTRETIEN DE L’OUTIL
Fixer et soutenir le matériel sur une plate-forme stable au moyen d’une bride de ser-
rage ou de tout autre dispositif semblable; le matériel est instable lorsqu’on le retient
manuellement ou quon l’appuie contre le corps, ce qui peut faire perdre la mtrise de l’outil.
Ne pas forcer l’outil ni l’utiliser pour des travaux autres que ceux pour lesquels il a
été conçu. Pour obtenir de meilleurs résultats et prévenir les risques de blessure, laisser
l’outil couper à la vitesse pour laquelle il a été conçu.
Ne pas utiliser l’outil lorsque l’interrupteur marche-arrêt ne fonctionne pas; tout outil
qui ne peut être commandé au moyen de linterrupteur est dangereux et doit être réparé.
D
A
Z
X
D-Handle Base - Base de la poignée fermée
Base con mango en D
Plunge Base - Base plongeante - Base para penetración
M
N
O
P
Q
R
T
U
L
M
S
F
F
B
C
Centering Tool
Outil de centrage
Herramienta
de centrado
VW
H
B
C
D
Y
I
J
Fixed Base - Base fixe - Base fija
A. QUICK RELEASE LATCH
B. DEPTH ADJUSTMENT RING
C. ADJUSTABLE SCALE
D. LOCKING LEVER
E. HANDLE
F. SUBBASE
G. SPEED DIAL (618 ONLY)
H. GUIDE PIN GROOVE
I. SPINDLE LOCK BUTTON
(618 ONLY)
J. COLLET NUT
K. TOGGLE SWITCH
L. DETACHABLE CORDSET
M. HOLES FOR UNIVERSAL
EDGE GUIDE
N. TRIGGER SWITCH
O. TRIGGER LOCK BUTTON
P. TURRET STOP
Q. DEPTH ADJUSTMENT ROD
R. PLUNGE LOCK LEVER
S. DUST SHROUD
T. DUST CAP
U. CENTERING TOOL
D
B
A
E
F
H
I
J
M
G
K
C
FIG. 1
FIG. 2
FIG. 3
Motor - Bloc moteur - Unidad del motor
A. VERROU DE DÉBLOCAGE RAPIDE
B. ANNEAU DE RÉGLAGE DE PROFONDEUR
C. ÉCHELLE RÉGLABLE
D. LEVIER DE VERROUILLAGE
E. POIGNÉE
F. SOUS-BASE
G.BOUTON DE RÉGLAGE DES VITESSES
(MODÈLE 618 SEULEMENT)
H. RAINURE DE LA GOUPILLE DE GUIDAGE
I. BOUTON DE VERROUILLAGE DE LA
BROCHE (MODÈLE 618 SEULEMENT)
J. ÉCROU DE LA DOUILLE DE SERRAGE
K. COMMUTATEUR À BASCULE
L. CORDON AMOVIBLE
M. ORIFICES POUR BORD-GUIDE UNIVERSEL
N. INTERRUPTEUR À GÂCHETTE
O. BOUTON DE VERROUILLAGE DE LA
GÂCHETTE
P. BUTÉE DE LA TOURELLE
Q. TIGE DE RÉGLAGE DE PROFONDEUR
R. LEVIER DE VERROUILLAGE DE PLONGÉE
S. ENVELOPPE ANTI-POUSSIÈRE
T. CAPUCHON ANTI-POUSSIÈRE
U. OUTIL DE CENTRAGE
A. SEGURO DE LIBERACN RÁPIDA
B. ANILLO DE AJUSTE DE PROFUNDIDAD
C. ESCALA AJUSTABLE
D. PALANCA DE SEGURIDAD
E. MANGO
F. SUB BASE
G. SELECTOR DE VELOCIDAD
(ÚNICAMENTE 618)
H. CANAL PARA PERNO GUÍA
I. BOTÓN DEL SEGURO DE LA FLECHA
J. TUERCA DE LA MORDAZA
K. INTERRUPTOR DE CAMBIO
L. CABLE DESMONTABLE
M. ORIFICIOS PARA GUÍA UNIVERSAL
PARA BORDES
N. GATILLO INTERRUPTOR
O. BOTÓN DE SEGURO DEL GATILLO
P. TOPE DE TORRETA
Q. VARILLA DE AJUSTE DE PROFUNDIDAD
R. PALANCA DE SEGURO DE PENETRACIÓN
S. CUBIERTA CONTRA POLVO
T. TAPA DE POLVO
U. HERRAMIENTA DE CENTRADO
FIG. 3 FIG. 4 FIG. 5
FIG. 6 AA
L
N
O
K
BB
CC
R
FIG. 7 FIG. 8
FF
EE
DD
GG
Q
F
HH
II
KK
JJ
LL 1
4
3
2G
FIG. 9 FIG. 10 FIG. 11 FIG. 12
SPEED SELECTION CHART
Material Cutter Diam. Electronic Control Settings
Setting 1 Setting 2 Setting 3 Setting 4 Setting 5 Setting 6
Model # DW618 8,000 rpm 12,000 rpm 14,000 rpm 18,000 rpm 21,000 rpm 24,000 rpm
Hardwood, e.g., oak Small (1/2") O X XX X
Medium (1/2"-1 1/8") O XX X
Large (over-1 1/8") X XX O
Softwood, e.g., pine Small (1/2") O X XX XX
Medium (1/2"-1 1/8") O X XX XX XX
Large (over-1 1/8") X XX O
Plastic-laminated chipboard Small (1/2") O X XX XX
Medium (1/2"-1 1/8") O X XX XX XX
Large (over-1 1/8") O XX X
Plastics/Solid Surface Small (1/2") O X X XX XX
Medium (1/2"-1 1/8") O XX XX X X
Large (over-1 1/8") X XX O
This table can serve only as a guide, since wood was a living material. Within the same species of timber hardness and density vary.
Speed settings are approximate.
KEY: XX very good X good O Satisfactory – not recommended
T
P


Produktspezifikationen

Marke: DeWalt
Kategorie: Router
Modell: DW616D

Brauchst du Hilfe?

Wenn Sie Hilfe mit DeWalt DW616D benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Router DeWalt

Bedienungsanleitung Router

Neueste Bedienungsanleitung für -Kategorien-