DeWalt DW443 Bedienungsanleitung

DeWalt Schleifmaschine DW443

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für DeWalt DW443 (36 Seiten) in der Kategorie Schleifmaschine. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/36

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

DW441, DW442, DW443, DW444

Right Angle Random Orbit Sanders

Ponceuses orbitales excentriques à angle droit

Lijadoras orbitales de movimiento múltiple de ángulo recto

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTES ADVERTENCIA:

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

English

WARNING! Read all instructions. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious injury. The term “power tool” in all of the warn-

ings listed below refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs and matching out-

lets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock. Replace or

repair damaged cords. Make sure your extension cord is in good

condition. Use only 3-wire extension cords that have 3-prong

grounding-type plugs and 3-pole receptacles that accept the

tool’s plug.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY DEWALT TOOL, CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258)

SANDING PAD

(HOOK AND LOOP - DW442 AND DW443)

(PSA- PRESSURE SENSITIVE ADHESIVE - DW441 AND DW444)

DUST BAG

SPEED CONTROL DIAL

(DW443 AND DW444)

ON/OFF SWITCH

SHROUD

English

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock. When using an

extension cord, be sure to use one heavy enough to carry the

current your product will draw. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating.

The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the

next heavier gauge. The smaller the gauge number, the heavier

the cord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power tool

while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating power

toolsmay result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate conditions will reduce

personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-

position before plugging in. Carrying power tools with your

finger on the switch or plugging in power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in unex-

pected situations.

f) Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught in

moving parts. Air vents often cover moving parts and should also

be avoided.

g) If devices are provided for the connection of dust extraction

and collection facilities, ensure these are connected and

properly used. Use of these devices can reduce dust-related

hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the bat-

tery pack from the power tool before making any adjust-

ments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condi-

Produktspezifikationen

Marke:	DeWalt
Kategorie:	Schleifmaschine
Modell:	DW443
Tiefe:	320 mm
Gewicht:	2700 g
Höhe:	125 mm
Energiequelle:	AC
Leistung:	530 W
Leerlaufdrehzahl (max.):	7600 RPM
Leerlauf-Oszillationsrate (max.):	6800 OPM
Schwingkreisdurchmesser:	5 mm
Schleifscheibendurchmesser:	150 mm
Exzentrizität:	2.5 mm
Leerlauf-Oszillationsrate (min.):	4000 OPM