DeWalt D25263K Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr DeWalt D25263K (7 Seiten) in der Kategorie Hamer. Dieser Bedienungsanleitung war fĂŒr 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/7
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIĂN, CENTROS DE SERVICIO Y PĂLIZA DE
GARANTĂA. ADVERTENCIA: LĂASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
DEWALT Industrial Tool Co., 701 Joppa Road, Towson, MD 21286
(DEC14) Part No. N401624 Copyright © 2014 DEWALT
D25133, D25260, D25262, D25263
The following are trademarks for one or more D WALT power tools: the yellow and black color scheme, the âDâ E
shaped air intake grill, the array of pyramids on the handgrip, the kit box conïŹ guration, and the array of lozenge-
shaped humps on the surface of the tool.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contĂĄctenos.
1-800-4-D WALT âą www.dewalt.comE
DeïŹ nitions: Safety Guidelines
The deïŹ nitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in .death or serious injury
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury.
NOTICE: may Indicates a practice which, if not avoided, not related to personal injury
result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL US E
TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, ïŹ re and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term âpower toolâ in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Cluttered or dark areas invite accidents.Keep work area clean and well lit.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
ïŹ ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. UnmodiïŹ ed plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the inïŹ uence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your ïŹ nger on the switch or energizing power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4) POWER TOOL USE AND CARE
a) The Do not force the power tool. Use the correct power tool for your application.
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power toolâs operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result in
a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualiïŹ ed repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety Instructions for Rotary Hammers
âą Wear ear protectors. Exposure to noise can cause hearing loss.
âą Use auxiliary handle(s) if supplied with the tool. Loss of control can cause personal injury.
âą Hold power tools by insulated gripping surfaces when performing an operation where
the cutting accessory may contact hidden wiring or its own cord. Cutting accessory
contacting a âliveâ wire may make exposed metal parts of the power tool âliveâ and could give
the operator an electric shock.
âą Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
âą Wear safety goggles or other eye protection. Hammering operations cause chips to ïŹ y. Flying
particles can cause permanent eye damage. Wear a dust mask or respirator for applications that
generate dust. Ear protection may be required for most applications.
âą Keep a ïŹ rm grip on the tool at all times. Do not attempt to operate this tool without
holding it with both hands. It is recommended that the side handle be used at all times.
Operating this tool with one hand will result in loss of control. Breaking through or encountering
hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before
use.
âą Do not operate this tool for long periods of time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by
taking frequent rest periods.
âą Do not recondition bits yourself. Chisel reconditioning should be done by an authorized
specialist. Improperly reconditioned chisels could cause injury.
âą Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and
bits may get extremely hot during operation. Small bits of broken material may damage bare
hands.
âą Never lay the tool down until the bit has come to a complete stop. Moving bits could
cause injury.
âą Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or material
chips could dislodge and cause injury.
âą Slightly worn chisels can be resharpened by grinding.
âą Keep the power cord away from the rotating bit. Do not wrap the cord around any part
of your body. An electric cord wrapped around a spinning bit may cause personal injury and
loss of control.
âą Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long
hair can be caught in moving parts.
âą An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is
16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using more than one extension to make up
the total length, be sure each individual extension contains at least the minimum wire size. The
following table shows the correct size to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the
cord.
Minimum Gauge for Cord Sets
Ampere Rating
Volts Total Length of Cord in Feet (meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
More
Than
Not More
Than AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use
face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
âą ANSI Z87.1 eye protection (CAN/CSA Z94.3),
âą ANSI S12.6 (S3.19) hearing protection,
âą NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
âą lead from lead-based paints,
âą crystalline silica from bricks and cement and other masonry products, and
âą arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to ïŹ lter out microscopic particles.
âą Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
âą The label on your tool may include the following symbols. The symbols and their deïŹ nitions are
as follows:
V ..................... volts A ........................ amperes
Hz ................... hertz W ....................... watts
min .................minutes or AC ............alternating current
or DC .....direct current or AC/DC .....alternating or direct current
...................Class I Construction no.......................no load speed
....
....
....
.......
...
...
.......
....
....
.......
...
...
.......
....
....
........
....
....
.....
.
.
.(grounded) n .........................rated speed
...................Class II Construction ....................... earthing terminal
(double insulated) .......................safety alert symbol
âŠ/min ............per minute BPM ...................beats per minute
IPM .................impacts per minute RPM ...................revolutions per minute
SPM ...............strokes per minute sfpm ...................surface feet per minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. D WALT tools are factory tested; if this tool does not E
operate, check power supply.
COMPONENTS (Fig. 1)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.
A. Variable speed switch F. Chuck
B. Main handle G. Depth adjustment rod
C. Forward/Reverse lever H. Side handle
D. Mode selector I. Depth rod button
E. Mode selector button J. Locking collar
INTENDED USE
These heavy-duty rotary hammers have been designed for professional drilling and hammerdrilling,
screwdriving and light chipping at various work sites (i.e., construction sites). use under DO NOT
wet conditions or in presence of ïŹ ammable liquids or gases.
These heavy-duty rotary hammers are professional power tools. DO NOT let children come into
contact with the tool. Supervision is required when inexperienced operators use this tool.
Active Vibration Control (Fig. 1)
D25262, D25263 ONLY
The active vibration control (K) reduces rebound vibration from the hammer mechanism. Reducing
hand and arm vibration allows for more comfortable use for longer periods of time and extends the
life of the unit.
For best vibration control, hold the tool with one hand on the main handle (B) and the other hand on
the side handle (H). Apply just enough pressure so the hammer is approximately mid-stroke.
The hammer only needs enough pressure to engage the active vibration control. Applying too much
pressure will not make the tool drill or chip faster and active vibration control will not engage.
D25133, D25262 Heavy-Duty 1" (26 mm) SDS Plus Rotary Hammers, Marteaux rotatifs industriels SDS Plus, 26îmm (1îpo),
Rotomartillos SDS Plus de 26îmm (1") para trabajos pesados
D25260 Heavy-Duty 7/8" (24 mm) SDS Plus Rotary Hammers, Marteaux rotatifs industriels SDS Plus, 24îmm (7/8îpo),
Rotomartillos SDS Plus de 24îmm (7/8") para trabajos pesados
D25263 Heavy-Duty 1-1/8" (28 mm) SDS Plus Rotary Hammer, Marteaux rotatifs industriels SDS Plus, 28 mm (1-1/8 po),
Rotomartillos SDS Plus de 28 mm ") para trabajos pesados(1-1/8
Mechanical Clutch
All rotary hammer drills are equipped with a torque limiting clutch that reduces the maximum torque
reaction transmitted to the operator in case of jamming of a drill bit. This feature also prevents the
gearing and electric motor from stalling. The torque limiting clutch has been factory-set and cannot
be adjusted.
Side Handle (Fig. 2)
WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle
properly installed and securely tightened. Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.
A side handle comes assembled with this rotary hammer. The side handle (H) can be ïŹtted to suit
both right-hand and left-hand users.
TO ADJUST THE SIDE HANDLE
1. Loosen the side handle (H) by turning it counterclockwise.
2. Rotate the side handle to the desired position.
3. Tighten the side handle by turning it clockwise.
Trigger Switch (Fig. 1)
To start the rotary hammer, depress the variable speed trigger switch (A). To stop rotary hammer,
release the switch.
NOTE: Use lower speeds for starting holes without a centerpunch, drilling in metal, plastics or
ceramics, or driving screws. Higher speeds are better for drilling in masonry for maximum efïŹ ciency.
VARIABLE SPEED
The variable speed trigger switch (A) permits speed control. The farther the trigger switch is
depressed, the higher the speed of the drill.
Forward/Reverse Lever (Fig. 1)
The forward/reverse lever (C) is used to reverse the rotary hammer for backing out fasteners or
jammed bits in drill-only mode.
CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque.
To reverse the rotary hammer, turn it off and align the forward/reverse lever (C) with the yellow arrow
pointing backward (viewed when holding drill in operating position).
To position the lever for forward operation, turn the rotary hammer off and align the forward/reverse
lever (C) with the yellow arrow pointing forward (viewed when holding drill in operating position).
Mode Selector (Fig. 3)
D25133, D25260, D25262, D25263
WARNING: Do not operate in drill or hammerdrill mode with a chisel bit in the chuck. Personal
injury and damage to tool may result.
NOTICE: Tool must come to a complete stop before activating the mode selector button or damage
to the tool may result.
DRILL-ONLY MODE
To use drill-only mode, press mode selector button (E) and turn the mode selector (D) so the yellow
arrow points to the corresponding symbol as shown. Use drill-only mode for wood, metal, and
plastics.
HAMMERDRILL MODE
To use hammerdrill mode, press the mode selector button (E) and turn the mode selector (D) so the
yellow arrow points to the corresponding symbol as shown. Use this mode for masonry drilling.
HAMMER-ONLY MODE
For light chiseling, press the mode selector button (E) and turn the mode selector (D) so the yellow
arrow points to the corresponding symbol as shown.
NOTE: The yellow arrow on the mode selector MUST be aligned with the one of the symbols at all
times. There are no operable positions between the positions.
SDS Plus Chuck (Fig. 1)
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
WARNING: Burn Hazard. ALWAYS wear gloves when changing bits. Accessible metal parts on
the tool and bits may get extremely hot during operation. Small bits of broken material may damage
bare hands.
WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) by gripping the
front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur.
To insert bit, insert shank of bit about 3/4" (19 mm), no further than 7/8" (24 mm) into chuck (F).
Push and rotate bit until it locks in place. The bit will be securely held.
To release bit, pull the chuck sleeve (F) back and remove the bit.
OPERATION
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source
before installing and removing accessories, before adjusting or when making repairs. An
accidental start-up can cause injury.
WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored
or clamped ïŹ rmly. If drilling thin material, use a wood âback-upâ block to prevent damage to the
material.
WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side
handle properly installed and securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize
control.
Proper Hand Position (Fig. 1, 4)
WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as
shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation
of a sudden reaction.
Proper hand position requires one hand on the side handle (H), with the other hand on the main
handle (B).
Drilling Tools
The machine is intended for hammerdrilling in concrete, brick and stone. It is also suitable for drilling
without impact in wood, metal, ceramic and plastic.
Chipping Tools
The machine is intended for chipping in concrete, brick and stone.
Drilling
Press mode selector button (E) and turn the mode selector (D) to the drill bit symbol for drilling, to the
hammer symbol for hammering or to the hammerdrill symbol for hammerdrilling.
DRILLING OPERATION
1. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-speed
steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. For MASONRY, use carbide-tipped bits or
masonry bits. A smooth, even ïŹ ow of dust indicates the proper drilling rate.
2. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit
biting, but do not push hard enough to stall the motor or deïŹ ect the bit.
3. Hold tool ïŹ rmly with both hands to control the twisting action of the drill.
WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip
the drill ïŹ rmly with both hands to control the twisting action and avoid injury.
4. IF DRILL STALLS RELEASE TRIGGER , it is usually because it is being overloaded.
IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK
TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL â THIS CAN
DAMAGE THE DRILL.
5. To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit
through the last fractional part of the hole.
6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent
jamming.
7. With variable speed drills there is no need to center punch the point to be drilled. Use a slow
speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep
enough to drill without the bit skipping out.
DRILLING IN METAL
An SDS Plus round shank adaptor chuck is required for metal drilling. Ensure that tool is in drill-only
mode. Start drilling with slow speed and increase to full power while applying ïŹ rm pressure on the
tool. A smooth even ïŹ ow of metal chips indicates the proper drilling rate. Use a cutting lubricant
when drilling metals. The exceptions are cast iron and brass which should be drilled dry.
NOTE: Large (5/16" to 1/2" [7.9 mm to 12.7 mm]) holes in steel can be made easier if a pilot hole
(5/32" to 3/16" [4 mm to 4.8 mm]) is drilled ïŹ rst.
DRILLING IN WOOD
An SDS Plus round shank adaptor chuck is required for drilling in wood. Ensure that tool is in drill-only
mode. Start drilling with slow speed and increase to full power while applying ïŹ rm pressure on the
tool. Holes in wood can be made with the same twist drills used for metal. These bits may overheat
unless pulled out frequently to clear chips from the ïŹ utes. For larger holes, use spade bits, power
auger bits, or hole saws. Work that is apt to splinter should be backed up with a block of wood.
HAMMERDRILL OPERATION
1. When drilling, use just enough force on the hammer to keep it from bouncing excessively or
ârisingâ off the bit. Too much force will cause slower drilling speeds, overheating, and a lower
drilling rate.
2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit
when drilling as this will cause clogging of the bit ïŹ utes and a slower drilling speed.
3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the
hole with the tool still running to help clear debris from the hole.
4. For masonry, use carbide-tipped bits or masonry bits. A smooth even ïŹ ow of dust indicates the
proper drilling rate.
FIG. 5
I
GH
FIG. 1
H
FIG. 2
Chipping and Chiseling (Fig. 1)
WARNING: Do not operate in drill or hammerdrill mode with a chisel bit in the chuck. Personal
injury and damage to tool may result.
1. Insert chisel while in hammerdrill mode and rotate to desired position.
2. Set the mode selector (D) to the hammer-only position.
3. Adjust the side handle (H) as required.
4. Switch on the tool and start working.
5. Always switch off the tool when work is ïŹnished and before unplugging.
Depth Rod (Fig. 5)
TO ADJUST THE DEPTH ROD
1. Push in and hold the depth rod release button (I) on the side handle.
2. Move the depth rod (G) so the distance between the end of the rod and the end of the bit equals
the desired drilling depth.
3. Release the button to lock rod into position. When drilling with the depth rod, stop when end of
rod reaches surface of material.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source
before installing and removing accessories, before adjusting or when making repairs. An
accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To
minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing
this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.
Lubrication
Your tool was properly lubricated before leaving the factory. In from two to six months, depending
upon use, take or send your tool to an authorized service center for a complete cleaning, inspection
and lubrication. Tools used constantly on production jobs will need relubrication more often. Also,
tools âout of serviceâ for long periods should be relubricated before being put back to work.
Accessories
WARNING: Since accessories, other than those offered by D WALT, have not been tested with E
this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,
only DEWALT recommended accessories should be used with this product.
Recommended accessories for use with your tool are available at extra cost from your local dealer or
authorized service center. If you need assistance in locating any accessory, please contact DEWALT
Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DEWALT (1-800-433-
9258) or visit our website: www.dewalt.com.
MAXIMUM RECOMMENDED CAPACITIES
D25260 D25133, D25262 D25263
Masonry 7/8" (24 mm) 1" (26 mm) 1-1/8" (28 mm)
Masonry
Optimum Capacity
3/16"â1/2"
(5 mmâ13 mm)
1/4"â5/8"
(6 mmâ16 mm)
1/4"â3/4"
(6 mmâ19 mm)
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT
authorized service center or other qualiïŹ ed service personnel. Always use identical replacement
parts.
G
F
D25133
FIG. 3
DRILL-ONLY MODE
MODE PERĂAGE SEULEMENT
MODO SĂLO TALADRO
HAMMERDRILL MODE
MODE PERFORATION-PERĂAGE
MODO TALADRO/PERCUTOR
CHISEL ROTATION
ROTATION DU BURIN
ROTACIĂN DE CINCELES
HAMMER-ONLY MODE
MODE PERFORATION SEULEMENT
MODO SĂLO MARTILLO
(D25133, D25260, D25262, D25263)
I
B
D
E
C
H
J
C
B
D
E
I
H
FJ
G
D25263
E
D
A
A
FIG. 4
K
Register Online
Thank you for your purchase. Register your product now for:
âą WARRANTY SERVICE: Registering your product will help you obtain more efïŹ cient warranty
service in case there is a problem with your product.
âą CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as ïŹ re, ïŹ ood or theft,
your registration of ownership will serve as your proof of purchase.
âą FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event
a safety notiïŹ cation is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three
years from the date of purchase. This warranty does not cover part failure due to normal wear or
tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.
com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or
damage caused where repairs have been made or attempted by others. This warranty gives you
speciïŹ c legal rights and you may have other rights which vary in certain states or provinces.
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
D25133, D25260
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the ïŹ rst year after purchase.
2 YEARS FREE SERVICE
D25262, D25263
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the ïŹ rst 2 years after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisïŹ ed with the performance of your DEWALT Power Tool, Laser, or Nailer
for any reason, you can return it within 90 days from the date of purchase with a receipt for a full
refund â no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country speciïŹ c warranty information contained in the packaging, call the
local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,
call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.
SPECIFICATIONS
D25133 D25260 D25262 D25263
Voltage 120 V AC~ 120 V AC~ 120 V AC~ 120 V AC~
Ampere rating 8 A 7 A 8 A 8.5 A
Power input 800W 800W 800W 900W
Frequency 60 Hz 60 Hz 60 Hz 60 Hz
RPM 0â1500 0â1500 0â1500 0â1450
BPM 0â5500 0â5500 0â5540 0â5350
DĂ©ïŹ nitionsî: lignes directrices en
matiÚre de sécurité
Les dĂ©ïŹ nitions ci-dessous dĂ©crivent le niveau de danger pour chaque
mot-indicateur employĂ©. Lire le mode dâemploi et porter une attention particuliĂšre
Ă ces symboles.
DANGERî : indique une situation dangereuse imminente qui, si elle nâest pas
évitée, la entraßnera mort ou des blessures graves.
AVERTISSEMENTî: indique une situation potentiellement dangereuse qui, si
elle nâest pas Ă©vitĂ©e, entraĂźner lapourrait mort ou des blessures graves.
ATTENTIONî : indique une situation potentiellement dangereuse qui, si elle
nâest pas Ă©vitĂ©e, entraĂźner des pourrait blessures lĂ©gĂšres ou modĂ©rĂ©es.
AVIS : indique une pratique ne posant aucun risque de dommages corporels
mais qui par contre, si rien nâest fait pour lâĂ©viter, poser despourrait risques de
dommages matériels.
POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE OUTIL
DEWALT, COMPOSEZ LE NUMĂRO SANS FRAIS : 1-800-4-D WALT (1-800-433-9258)E.
AVERTISSEMENT : aïŹ n de rĂ©duire le risque de blessures, lire le mode dâemploi de lâoutil.
Avertissements de sécurité généraux pour les outils
Ă©lectriques
AVERTISSEMENT ! Lire tous les avertissements de sécurité et toutes les directives.
Le non-respect des avertissements et des directives pourrait se solder par un choc Ă©lectrique,
un incendie et/ou une blessure grave.
CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES
DIRECTIVES POUR UN USAGE ULTĂRIEUR
Le terme « outil Ă©lectrique » citĂ© dans les avertissements se rapporte Ă votre outil Ă©lectrique Ă
alimentation sur secteur (avec ïŹ l) ou par piles (sans ïŹ l).
1) SĂCURITĂ DU LIEU DE TRAVAIL
a) Tenir lâaire de travail propre et bien Ă©clairĂ©e. Les lieux encombrĂ©s ou sombres sont
propices aux accidents.
b) Ne pas faire fonctionner dâoutils Ă©lectriques dans un milieu dĂ©ïŹ agrant, tel quâen
prĂ©sence de liquides, de gaz ou de poussiĂšres inïŹ ammables. Les outils Ă©lectriques
produisent des Ă©tincelles qui pourraient enïŹ ammer la poussiĂšre ou les vapeurs.
c) Ăloigner les enfants et les personnes Ă proximitĂ© pendant lâutilisation dâun outil
Ă©lectrique. Une distraction pourrait en faire perdre la maĂźtrise Ă lâutilisateur.
2) SĂCURITĂ EN MATIĂRE DâĂLECTRICITĂ
a) Les ïŹ ches des outils Ă©lectriques doivent correspondre Ă la prise. Ne jamais modiïŹ er
la ïŹ che dâaucune façon. Ne jamais utiliser de ïŹ che dâadaptation avec un outil
Ă©lectrique mis Ă la terre. Le risque de choc Ă©lectrique sera rĂ©duit par lâutilisation de ïŹ ches
non modiïŹ Ă©es correspondant Ă la prise.
b) Ăviter tout contact physique avec des surfaces mises Ă la terre comme des tuyaux,
des radiateurs, des cuisiniÚres et des réfrigérateurs. Le risque de choc électrique est
plus élevé si votre corps est mis à la terre.
c) Ne pas exposer les outils Ă©lectriques Ă la pluie ou Ă lâhumiditĂ©. La pĂ©nĂ©tration de lâeau
dans un outil Ă©lectrique augmente le risque de choc Ă©lectrique.
d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour
transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de
la chaleur, de lâhuile, des bords tranchants et des piĂšces mobiles. Les cordons
endommagĂ©s ou enchevĂȘtrĂ©s augmentent les risques de choc Ă©lectrique.
e) Pour lâutilisation dâun outil Ă©lectrique Ă lâextĂ©rieur, se servir dâune rallonge convenant
Ă cette application. Lâutilisation dâune rallonge conçue pour lâextĂ©rieur rĂ©duira les risques de
choc Ă©lectrique.
f) Sâil est impossible dâĂ©viter lâutilisation dâun outil Ă©lectrique dans un endroit humide,
brancher lâoutil dans une prise ou sur un circuit dâalimentation dotĂ©s dâun disjoncteur
de fuite Ă la terre (GFCI). Lâutilisation de ce type de disjoncteur rĂ©duit les risques de choc
Ă©lectrique.
3) SĂCURITĂ PERSONNELLE
a) Ătre vigilant, surveiller le travail effectuĂ© et faire preuve de jugement lorsquâun outil
Ă©lectrique est utilisĂ©. Ne pas utiliser dâoutil Ă©lectrique en cas de fatigue ou sous
lâinïŹ uence de drogues, dâalcool ou de mĂ©dicaments. Un simple moment dâinattention
en utilisant un outil Ă©lectrique peut entraĂźner des blessures corporelles graves.
b) Utiliser des Ă©quipements de protection individuelle. Toujours porter une protection
oculaire. Lâutilisation dâĂ©quipements de protection comme un masque antipoussiĂšre, des
chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la
situation le requiert réduira les risques de blessures corporelles.
c) EmpĂȘcher les dĂ©marrages intempestifs. Sâassurer que lâinterrupteur se trouve Ă la
position dâarrĂȘt avant de relier lâoutil Ă une source dâalimentation et/ou dâinsĂ©rer un
bloc-piles, de ramasser ou de transporter lâoutil. Transporter un outil Ă©lectrique alors
que le doigt repose sur lâinterrupteur ou brancher un outil Ă©lectrique dont lâinterrupteur est Ă la
position de marche risque de provoquer un accident.
d) Retirer toute clĂ© de rĂ©glage ou clĂ© avant de dĂ©marrer lâoutil. Une clĂ© ou une clĂ© de
rĂ©glage attachĂ©e Ă une partie pivotante de lâoutil Ă©lectrique peut provoquer des blessures
corporelles.
e) Ne pas trop tendre les bras. Conserver son Ă©quilibre en tout temps. Cela permet de
mieux maĂźtriser lâoutil Ă©lectrique dans les situations imprĂ©vues.
f) Sâhabiller de maniĂšre appropriĂ©e. Ne pas porter de vĂȘtements amples ni de bijoux.
Garder les cheveux, les vĂȘtements et les gants Ă lâĂ©cart des piĂšces mobiles. Les
vĂȘtements amples, les bijoux ou les cheveux longs risquent de rester coincĂ©s dans les piĂšces
mobiles.
g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage
et de ramassage, sâassurer que ceux-ci sont bien raccordĂ©s et utilisĂ©s. Lâutilisation
dâun dispositif de dĂ©poussiĂ©rage peut rĂ©duire les dangers engendrĂ©s par les poussiĂšres.
4) UTILISATION ET ENTRETIEN DâUN OUTIL ĂLECTRIQUE
a) Ne pas forcer un outil Ă©lectrique. Utiliser lâoutil Ă©lectrique appropriĂ© Ă lâapplication.
Lâoutil Ă©lectrique appropriĂ© effectuera un meilleur travail, de façon plus sĂ»re et Ă la vitesse pour
laquelle il a été conçu.
b) Ne pas utiliser un outil Ă©lectrique dont lâinterrupteur est dĂ©fectueux. Tout outil
Ă©lectrique dont lâinterrupteur est dĂ©fectueux est dangereux et doit ĂȘtre rĂ©parĂ©.
c) DĂ©brancher la ïŹ che de la source dâalimentation et/ou du bloc-piles de lâoutil
Ă©lectrique avant de faire tout rĂ©glage ou changement dâaccessoire ou avant de
ranger lâoutil. Ces mesures prĂ©ventives rĂ©duisent les risques de dĂ©marrage accidentel de
lâoutil Ă©lectrique.
d) Ranger les outils électriques hors de la portée des enfants et ne permettre à aucune
personne nâĂ©tant pas familiĂšre avec un outil Ă©lectrique ou son mode dâemploi
dâutiliser cet outil. Les outils Ă©lectriques deviennent dangereux entre les mains dâutilisateurs
inexpérimentés.
e) Entretien des outils Ă©lectriques. VĂ©riïŹ er si les piĂšces mobiles sont mal alignĂ©es ou
coincées, si des piÚces sont brisées ou présentent toute autre condition susceptible
de nuire au bon fonctionnement de lâoutil Ă©lectrique. En cas de dommage, faire
rĂ©parer lâoutil Ă©lectrique avant toute nouvelle utilisation. Beaucoup dâaccidents sont
causés par des outils électriques mal entretenus.
f) Sâassurer que les outils de coupe sont aiguisĂ©s et propres. Les outils de coupe bien
entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maßtriser.
g) Utiliser lâoutil Ă©lectrique, les accessoires, les forets, etc. conformĂ©ment aux
prĂ©sentes directives en tenant compte des conditions de travail et du travail Ă
effectuer. Lâutilisation dâun outil Ă©lectrique pour toute opĂ©ration autre que celle pour laquelle
il a été conçu est dangereuse.
5) RĂPARATION
a) Faire rĂ©parer lâoutil Ă©lectrique par un rĂ©parateur professionnel en nâutilisant que des
piÚces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire de
lâoutil Ă©lectrique.
Consignes de sécurité additionnelles propres aux marteaux
rotatifs
⹠Porter un dispositif de protection auditif. Le bruit en résultant pourrait occasionner une perte
de lâacuitĂ© auditive.
âą Utiliser la/les poignĂ©e(s) auxiliaire(s) si fournie(s) avec lâoutil. Une perte de contrĂŽle de
lâoutil pourrait occasionner des dommages corporels.
âą Tenir lâoutil Ă©lectrique par les surfaces isolĂ©es prĂ©vues Ă cet effet pendant toute
utilisation oĂč lâorgane de coupe pourrait entrer en contact avec des fils Ă©lectriques
cachĂ©s ou son propre cordon. Tout contact de lâorgane de coupe avec un fil sous tension
mettra les parties mĂ©talliques exposĂ©es de lâoutil Ă©lectrique sous tension et Ă©lectrocutera
lâutilisateur.
âą Utiliser des serre-joints, ou tout autre moyen, pour ïŹ xer et immobiliser le matĂ©riau sur
une surface stable. Tenir la piĂšce Ă la main ou contre son corps offre une stabilitĂ© insufïŹ sante
qui pourrait vous en faire perdre le contrĂŽle.
âą Porter des lunettes de protection ou toute autre protection oculaire. Le martelage
pourrait faire voltiger des Ă©clats. Ces particules volantes pourraient occasionner des dommages
oculaires permanents. Porter un masque anti-poussiĂšres ou un appareil de protection des voies
respiratoires pour toute application productrice de poussiĂšres. Une protection auditive peut
sâavĂ©rer nĂ©cessaire pour la plupart des applications.
âą Maintenir systĂ©matiquement lâoutil fermement. Ne pas tenter dâutiliser cet outil
sans le maintenir Ă deux mains. Il est recommandĂ© dâutiliser systĂ©matiquement la poignĂ©e
latĂ©rale. Le fait dâutiliser cet outil Ă une main pourra vous en faire perdre le contrĂŽle. Traverser ou
rencontrer des matĂ©riaux durs comme les armatures peut aussi sâavĂ©rer dangereux. Resserrer
soigneusement la poignée latérale avant toute utilisation.
⹠Ne pas utiliser cet outil pendant des périodes de temps prolongées. Les vibrations
causées par la percussion peuvent poser des risques pour les mains ou les bras. Porter des
gants pour amortir les vibrations, et pour limiter les risques, faire des pauses fréquentes.
âą Ne pas remettre Ă neuf les forets soi-mĂȘme. La remise Ă neuf de tout burin doit ĂȘtre
effectuée par un spécialiste agréé. Tout burin remis à neuf incorrectement pose des risques de
dommages corporels.
âą Porter des gants lors de lâutilisation de lâoutil ou le changement de mĂšche. Les parties
mĂ©talliques accessibles de lâoutil et des mĂšches/forets pourraient sâavĂ©rer brĂ»lantes lors de
lâutilisation. De petits dĂ©bris de matĂ©riau pourraient aussi blesser les mains nues.
âą Attendre systĂ©matiquement lâarrĂȘt complet de la mĂšche/foret avant de dĂ©poser lâoutil
oĂč que ce soit. Des forets/mĂšches en rotation posent des risques de dommages corporels.
⹠Ne pas donner des coups de marteau sur des forets/mÚches coincés pour les déloger.
Des fragments de mĂ©tal ou de matĂ©riau pourraient ĂȘtre Ă©jectĂ©s et causer des dommages
corporels.
âą Les burins lĂ©gĂšrement usĂ©s peuvent ĂȘtre rĂ©affutĂ©s.
âą Maintenir le cordon dâalimentation Ă lâĂ©cart dâune mĂšche en rotation. Ne pas enrouler
le cordon autour dâune partie quelconque de votre corps. Un cordon Ă©lectrique enroulĂ©
autour dâune mĂšche en rotation pose des risques de dommages corporels et de perdre le
contrĂŽle de lâoutil.
⹠Prendre des précautions à proximité des évents, car ils cachent des piÚces mobiles.
VĂȘtements amples, bijoux ou cheveux longs risquent de rester coincĂ©s dans ces piĂšces mobiles.
âą Pour la sĂ©curitĂ© de lâutilisateur, utiliser une rallonge de calibre adĂ©quat (AWG, American
Wire Gauge [calibrage amĂ©ricain normalisĂ© des ïŹ ls Ă©lectriques]). Plus le calibre est
petit, et plus sa capacitĂ© est grande. Un calibreî16, par exemple, a une capacitĂ© supĂ©rieure
Ă un calibreî18. Lâusage dâune rallonge de calibre insufïŹ sant causera une chute de tension qui
entraĂźnera perte de puissance et surchauffe. Si plus dâune rallonge est utilisĂ©e pour obtenir une
certaine longueur, sâassurer que chaque rallonge prĂ©sente au moins le calibre de ïŹ l minimum.
Le tableau ci-dessous illustre les calibres Ă utiliser selon la longueur de rallonge et lâintensitĂ©
nominale indiquée sur la plaque signalétique. En cas de doute, utiliser le calibre suivant. Plus le
calibre est petit, plus la rallonge peut supporter de courant.
Calibres minimaux des rallonges
Intensité (en ampÚres) volts Longueur totale de cordon en mÚtres (pieds)
120 V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)
240 V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)
Supérieur à Inférieur à AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Non recommandé
AVERTISSEMENTî: porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes
courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussiĂšres si
la dĂ©coupe doit en produire beaucoup. PORTER SYSTĂMATIQUEMENT UN ĂQUIPEMENT DE
SĂCURITĂ HOMOLOGUĂî:
âą Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3)î;
âą Protection auditive ANSI S12.6 (S3.19)î;
âą Protection des voies respiratoires NIOSH/OSHA/MSHA.
AVERTISSEMENTî : les scies, meules, ponceuses, perceuses ou autres outils de construction
peuvent produire des poussiĂšres contenant des produits chimiques reconnus par lâĂtat californien
pour causer cancers, malformations congĂ©nitales ou ĂȘtre nocifs au systĂšme reproducteur. Parmi
ces produits chimiques, on retrouveî:
âą Le plomb dans les peintures Ă base de plombî;
âą La silice cristallisĂ©e dans les briques et le ciment, ou autres produits de maçonnerieî; et
âą Lâarsenic et le chrome dans le bois ayant subi un traitement chimique.
Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces travaux.
Pour rĂ©duire toute exposition Ă ces produitsî: travailler dans un endroit bien aĂ©rĂ©, en utilisant du
matĂ©riel de sĂ©curitĂ© homologuĂ©, tel un masque antipoussiĂšres spĂ©cialement conçu pour ïŹ ltrer les
particules microscopiques.
⹠Limiter toute exposition prolongée avec les poussiÚres provenant du ponçage, sciage,
meulage, perçage ou toute autre activitĂ© de construction. Porter des vĂȘtements de
protection et nettoyer Ă lâeau savonneuse les parties du corps exposĂ©es. Le fait de laisser
la poussiĂšre pĂ©nĂ©trer dans la bouche, les yeux ou la peau peut favoriser lâabsorption de produits
chimiques dangereux.
AVERTISSEMENTî : cet outil peut produire et/ou rĂ©pandre de la poussiĂšre susceptible de
causer des dommages sérieux et permanents au systÚme respiratoire. Utiliser systématiquement
un appareil de protection des voies respiratoires homologuĂ© par le NIOSH ou lâOSHA. Diriger les
particules dans le sens opposé au visage et au corps.
AVERTISSEMENTî : pendant lâutilisation, porter systĂ©matiquement une protection
auditive individuelle adéquate homologuée ANSI S12.6 (S3.19). Sous certaines conditions
et suivant la durĂ©e dâutilisation, le bruit Ă©manant de ce produit pourrait contribuer Ă une perte de
lâacuitĂ© auditive.
âą LâĂ©tiquette apposĂ©e sur votre outil peut inclure les symboles suivants. Les symboles et leur
dĂ©ïŹ nition sont indiquĂ©s ci-aprĂšsî:
V ....................volts A .......................ampĂšres
Hz ..................hertz W ......................watts
min ................minutes ou AC ..........courant alternatif
ou DC ....courant continu ou AC/DC ....courant alternatif ou
..................classe I fabrication continu
(mis Ă la terre) no ......................vitesse Ă vide
..................fabrication classe II n ........................vitesse nominale
(double isolation) ......................borne de terre
âŠ/min ...........par minute ......................symbole dâavertissement
IPM ................impacts par minute BPM ..................battements par minute
sfpm ..............pieds linéaires par minute (plpm) r/min ..................tours par minute
SPM (FPM) ....fréquence par minute
Produktspezifikationen
| Marke: | DeWalt |
| Kategorie: | Hamer |
| Modell: | D25263K |
Brauchst du Hilfe?
Wenn Sie Hilfe mit DeWalt D25263K benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Hamer DeWalt
3 Oktober 2024
29 September 2024
18 September 2024
13 September 2024
6 September 2024
5 September 2024
5 September 2024
4 September 2024
4 September 2024
18 August 2024
Bedienungsanleitung Hamer
- Hamer Makita
- Hamer Bosch
- Hamer AEG
- Hamer Powerfix
- Hamer Black And Decker
- Hamer Cocraft
- Hamer FERM
- Hamer Ryobi
- Hamer Topcraft
- Hamer Trotec
- Hamer Hilti
- Hamer Einhell
- Hamer Hikoki
- Hamer Hitachi
- Hamer Metabo
- Hamer Stanley
- Hamer GĂŒde
- Hamer Scheppach
- Hamer Milwaukee
- Hamer CMI
- Hamer Craftsman
- Hamer Powerplus
- Hamer Porter-Cable
- Hamer Global
- Hamer Goon
- Hamer Einhell Bavaria
- Hamer McKenzie
- Hamer Anova
Neueste Bedienungsanleitung fĂŒr -Kategorien-
30 September 2024
16 September 2024
14 September 2024
13 September 2024
10 September 2024
6 September 2024
6 September 2024
5 September 2024
5 September 2024
5 September 2024