Davis 7716 tripod Bedienungsanleitung

Davis Stativ 7716 tripod

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Davis 7716 tripod (8 Seiten) in der Kategorie Stativ. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

Mounting Tripod Kit

Installation Manual

For use with Davis’s wireless and cabled Vantage Pro2 weather stations, the

Mounting Tripod simplifies installation. The tripod supports the Integrated

Sensor Suite (ISS) or other station, and features an adjustable foot pad

which enables mounting on level surfaces or roof peaks.

Components

The Mounting Tripod includes the following poles and mounting hardware.

Please make sure you have everything you need before beginning.

Poles

Hardware

Tripod

Anemometer

Extension

Tube

Long

Extension

Tube

(swaged end)

5/16" Flat Washers

5/16" Lock Washers

5/16"

Lock Washer

1/4" Bolt screws

Hex Nut

Label

Pitch Pads

5/16" Heavy Duty

Hex Nuts

5/16" Bolt screws

Bracket

U-Bolt

1/4" x 2" Lag Screws

5/16" Square Nuts

8" Cable Ties

Saddle

Vertical

Stop

Plate

Hex Nuts

Heavy Duty

Tripod Assembly

Tools for Setup

• Adjustable wrench

• Compass or local area map

• Drill with 3/16" or 13/64" (5 mm) bit for the 1/4" lag screws

Tripod Assembly

Follow the instructions below to assemble the tripod.

1. Unfold the tripod so the two foot pads which come pre-installed on the

tripod legs are flat on the ground.

2. Thread a hex nut almost all the way onto all six of the 5/16" bolts.

3. Insert one of the 5/16" bolts into the hole in vertical stop plate.

4. Insert the 5/16" bolt with vertical stop plate into one of the holes in the

tripod's lower bracket and thread a square nut onto the end of the bolt, on

the inside of the bracket.

Do not thread the square nut too far up the bolt.

5. Repeat this procedure for the remaining 5/16" bolts. Place them into the

holes in both the top and bottom tripod brackets, threading a square nut on

the end of each bolt.

Do not thread the square nuts too far up the bolts.

6. Insert the long extension tube into the tripod, sliding it through the brackets.

The vertical stop plate should keep the tube from sliding all the way

through.

7. Secure the extension tube by tightening the square and hex nuts on the

5/16" bolts until the bolts hold the tube in place securely.

5/16" Bolt

Hex Nut

Square Nut

Assemble nuts and bolts

in Tripod brackets.

Do not tighten.

Use Vertical Stop Plate

on one of the lower

bracket bolts.

Slide Long Extension Tube

through center of Tripod brackets.

Tighten nuts and bolts.

Vertical

Stop Plate

Long

Extension

Tube

Mounting the Tripod

8. Attach the foot bracket to the tripod

leg as shown.

Apply pitch pads to the bottom of the

foot bracket and the two foot

brackets that come pre-installed on

the tripod.

Mounting the Tripod

Mount the tripod with long extension tube on the desired surface, as shown

below. On the following pages are instructions for securing your sensor array

or ISS onto the long extension tube.

ROOF MOUNTING DECK MOUNTING

ISS ISS

Long Extension Tube

(use level or plumb line

to nd true vertical)

Deck or other

at surface

Tighten nut when

proper angle of feet

determined

Long Extension Tube

1/4 x2”

Lag Screw

(6 places)

Flat

Washer

1/4 x2”

Lag Screw

(6 places)

Flat

Washer

Note: Any metal object may attract a lightning strike, including your weather

station or tripod. If lightning strikes your station or strikes somewhere

nearby, the station's internal electronics may suffer anywhere between little

to extensive damage. The station itself has been designed with

considerable surge protection, but to safeguard nearby equipment and

structures, we recommend following local recommendations on properly

grounding your installation.

Hex

Nut Lock

Washer

1/4" Bolt

Foot Bracket

Front Leg

Pitch Pad

Produktspezifikationen

Marke:	Davis
Kategorie:	Stativ
Modell:	7716 tripod
Produktfarbe:	Edelstahl
Zweck:	Wetterstation
Material:	Stahl
Höhe (max):	- mm
Höchstgewichtskapazität:	- kg
Anzahl der Beine:	3 Bein(e)