Da-Lite Tensioned Conference Electrol Bedienungsanleitung

Da-Lite Videokonferenzsystem Tensioned Conference Electrol

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Tensioned Conference Electrol (8 Seiten) in der Kategorie Videokonferenzsystem. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

INSTRUCTION BOOK FOR

Tensioned Conference Electrol

Installation

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

3. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

4. Do NOT lift or push up on the camera arm mechanism at any

time. This may cause improper operation and/or component

failure or injury to persons.

5. Failure to provide adequate structural strength for this

component can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the

structure to which this component is attached can support the

weight of all equipment. Reinforce the structure as required

before installing the component.

6. Use this projection screen only for its intended use as described

in these instructions. Do not use attachments not recommended

by the manufacturer.

Save These Instructions

Pre-Installation

1. Carefully unpack screen and remove outer wrapping from case.

2. Make sure to recheck measurements of screen location

before installation.

Hand Hole

Internal

Bracket

Figure 1a – Threaded Rod with Internal Bracket

Figure 1b – Threaded Rod with Internal and External Bracket

Figure 1c – Internal Bracket

Hand Hole

NOTE: Unit is not to be installed in air handling spaces.

1. The case brackets provide multiple attachment points for bolts,

cables, or threaded rod. The following page shows two locations

for typical threaded rod installations with the external case

mounting brackets (Figure 1a) and without them (Figure 1b). The

internal case brackets can be accessed through the hand holes

(Figure 1c).

Original Instructions

Disclaimer

Milestone and its ailiated corporations and subsidiaries

(collectively "Milestone"), intend to make this manual accurate

and complete. However, Milestone makes no claim that the

information contained herein covers all details, conditions or

variations, nor does it provide for every possible contingency in

connection with the installation or use of this subject to change

without notice or obligation of any kind. Milestone makes no

representation of warranty, expressed or implied, regarding the

information contained herein. Milestone assumes no

responsibility for accuracy, completeness or suiciency of the

information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies.

Installation (continued

Figure 2 – Bottom of Case Figure 3 – Bottom of Case

Shipping Bracket

Secondary Low

Voltage Cover

Primary Junction Box Cover

Access Door

Door Screw Door Screw

2. The case has a self-trimming lange around the bottom. Ceiling

tiles or drywall may be placed on top of this lange to provide a

inished appearance.

3. After securing the case in the ceiling, check that the case is level

and plumb.

4. Use supplied 1/8” nex key and a 1/4” wrench to remove silver

shipping brackets attached to slat and screen case.

5. Install electrical connections that apply to your unit. Refer to the

electrical diagram`. The electrical connections are accessible by

removing the two screws on the primary junction box cover and

the two screws on the secondary low voltage cover (Figure 2).

You can remove the access door if needed to allow for greater

access to the electrical wiring. To remove the access door;

remove the screw from each end of the door while holding the

door and slide the door of the langes (Figure 3).

NOTE: Must be installed in accordance with the requirements of

the Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.

6. Remove shipping brackets by removing the hex head screws

from aluminum slat and case. Slat should move freely (Figure 2).

(Only if the roller assembly is pre installed.)

7. Test installation by operating the screen several times. Be

prepared to stop the screen. Standard Duty Cycle: 1MIN. ON/3

MIN. OFF. The fabric door (rear door) will not close until the wall

switch is placed in the up position and when the screen motor

stops at its limit switch in the up direction.

CAUTION: Excessive continuous operation may cause the

motor to overheat. If this happens the motor will shut of

until it cools to a normal operating temperature.

ATTENTION! Le fonctionnement continu et excessif peut

provoquer une surchaufe.Si cela se produit, les moteurs

s'arrêteront jusqu'à qu'ils se soient refroidis à la température

normale de fonctionnement.

8. Run the screen down enough to open the fabric door. Insert

the access door on the langes and reinstall the screws to

secure the door.

Produktspezifikationen

Marke:	Da-Lite
Kategorie:	Videokonferenzsystem
Modell:	Tensioned Conference Electrol
Gewicht:	182800 g
Produktfarbe:	Weiß
Natives Seitenverhältnis:	16:10
Gehäusefarbe:	Weiß
Einsehbare Bildschirmhöhe (H):	1840 mm
Einsehbare Bildschirmbreite (B):	2950 mm
Diagonal:	137 Zoll
Antriebstyp:	Motorisiert
Gesamte Bildschirmgröße (Höhe x Breite):	- cm
Format:	weit
Leuchtdichtefaktor:	1
Sichtwinkel:	60 °
Schwarzer Vorlauf:	180 mm
Gehäuse L1:	3640 mm