D-Link DGS-1510 Bedienungsanleitung

D-Link Schalter DGS-1510

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für D-Link DGS-1510 (56 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 40 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/56
Documentation also available on
CD and D-Link Website
Getting Started Guide
Erste Schritte
Guide de démarrage
Guida introduttiva
Guía de introducción
Краткое руководство пользователя
Guia inicial
快速安裝指南
Petunjuk Pemasangan
本製品のご利用にあたって
快速安裝指南
Getting Started Guide For
D-Link SmartPro Switch
2
ENGLISH
About This Guide
This guide gives step-by-step instructions for setting up
all D-Link SmartPro switches and relative Warranty,
Safety, Regulatory, and Environment Notice. Please note
that the model you have purchased may appear slightly
different from those shown in the illustrations.
For more detailed information about your switch, its
components, making network connections, and technical
specications, please refer to the User’s Guide included
with your switch.
Step 1 – Unpacking
Open the shipping carton and carefully unpack its
contents. Please consult the packing list located in the
User Guide to make sure all items are present and
undamaged. If any item is missing or damaged, please
contact your local D-Link reseller for replacement.
- One D-Link SmartPro Switch
- Rack mounting bracket
- Rubber Feet
- Power cord
- One console cable
- Power cord clip
- User’s Guide CD with DNA (D-Link Network Assistant)
program
- One multilingual Getting Started Guide
Step 2 – Switch Installation
For safe switch installation and operation, it is
recommended that you:
• Visually inspect the power cord to see that it is secured
fully to the AC power connector.
• Make sure that there is proper heat dissipation and
adequate ventilation around the switch.
• Do not place heavy objects on the switch
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the
rubber feet included with the device must be attached
on the bottom at each corner of the device’s base. Allow
enough ventilation space between the device and the
objects around it.
Figure 1. Attaching the rubber feet
Installing Power Cord Clip
To prevent accidental removal of the AC power cord, it is
recommended to install the power cord clip together with
the power cord.
1. With the rough side facing down, insert the Tie Wrap
into the hole below the power socket.
Figure 2-1. Insert Tie Wrap to the Switch
2. Plug the AC power cord into the power socket of the
Switch.
Figure 2-2. Connect the power cord to the Switch
3. Slide the Retainer through the Tie Wrap until the end
of the cord.
Figure 2-3. Slide the Retainer through the Tie Wrap
4. Circle the tie of the Retainer around the power cord
and into the locker of the Retainer.
Figure 2-4. Circle around the power cord
3
ENGLISH
5. Fasten the tie of the Retainer until the power cord is
secured.
Figure 2-5. Secure the power cord
Rack Installation
The switch can be mounted in an EIA standard size
19-inch rack, which can be placed in a wiring closet with
other equipment. To install, attach the mounting brackets
to the switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 3. Attaching the mounting brackets
Then, use the screws provided with the equipment rack
to mount the switch in the rack.
Figure 4. Installing the switch in a standard-sized
equipment rack
Step 3 – Plugging in the AC
Power Cord
You can now connect the AC power cord into the rear of
the switch and to an electrical outlet (preferably one that
is grounded and surge protected).
Figure 5. Plugging the switch into an outlet
Power Failure
As a precaution, the switch should be unplugged in
case of power failure. When power is resumed, plug the
switch back in.
Management Options
This system may be managed out-of-band through the
console port on the front/back panel or in-band using
Telnet. The user may also choose the web-based
management, accessible through a web browser. Each
Switch must be assigned its own IP Address, which is
used for communication with an SNMP network manager
or other TCP/IP application (for example BOOTP, TFTP).
The Switch’s default IP address is 10.90.90.90. The user
can change the default Switch IP address to meet the
specication of your networking address scheme.
Web-based Management Interface
After a successful physical installation, you can congure
the switch, monitor the LED panel, and display statistics
graphically using a web browser, such as Netscape
Navigator (version 6.2 and higher) or Microsoft ® Internet
Explorer (version 5.0 and higher).
You need the following equipment to begin the web
conguration of your device:
A PC with a RJ-45 Ethernet connection
A standard Ethernet cable
Step 1
Connect the Ethernet cable to any of the ports in front
panel of the switch and to the Ethernet port on the PC.
Figure 6. Connected Ethernet cable


Produktspezifikationen

Marke: D-Link
Kategorie: Schalter
Modell: DGS-1510
Breite: 280 mm
Tiefe: 180 mm
Gewicht: 1240 g
Produktfarbe: Schwarz
Höhe: 44 mm
AC Eingangsspannung: 100 - 240 V
AC Eingangsfrequenz: 50 - 60 Hz
Betriebstemperatur: -5 - 50 °C
Relative Luftfeuchtigkeit in Betrieb: 0 - 95 %
Verpackungsbreite: 346 mm
Verpackungstiefe: 346 mm
Verpackungshöhe: 104 mm
Paketgewicht: 2710 g
Netzstandard: IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ae, IEEE 802.3u, IEEE 802.3x
Quality of Service (QoS) Support: Ja
Zertifizierung: CE, FCC, C-Tick, VCCI, BSMI, CCC
Vollduplex: Ja
Stromverbrauch (Standardbetrieb): 20.3 W
Power over Ethernet (PoE): Nein
Warentarifnummer (HS): 85176990
LED-Anzeigen: Activity, Link, Power
Temperaturbereich bei Lagerung: -20 - 70 °C
Luftfeuchtigkeit bei Lagerung: 0 - 90 %
Geräuschpegel: 43.8 dB
Switch-Typ: Managed
Anzahl der basisschaltenden RJ-45 Ethernet Ports: 16
Basic Switching RJ-45 Ethernet Ports-Typ: Gigabit Ethernet (10/100/1000)
Netzstecker: DC-Anschluss
Auto MDI/MDI-X: Ja
10G-Unterstützung: Ja
MAC-Adressentabelle: 16000 Eintragungen
Routing-/Switching-Kapazität: 76 Gbit/s
Jumbo Frames Unterstützung: Ja
Rack-Einbau: Ja
Web-basiertes Management: Ja
Multicast Unterstützung: Ja
Head-of-Line (HOL)-Blocking: Ja
Port-Spiegelung: Ja
Link Aggregation: Ja
VLAN-Unterstützung: Ja
DHCP-Funktionen: DHCP server, DHCP client
Management-Protokolle: Telnet, SNMP, SNTP, ICMPv6, IPv4/v6, RMON v1, LLDP, LLDP-MED, NTP, Telnet
Palettenlänge (brutto): 1100 mm
Palettenbreite (brutto): 1200 mm
MAC Adressen Filtern: Ja
Store-and-Forward: Ja
Stapelbar: Ja
Sicherheit: cUL, CB
Auto-Negotiation-Funktion: Ja
unterstütze Kabeltypen: Cat5, Cat5e
Unterstützung Datenflusssteuerung: Ja
Broadcast-Sturmkontrolle: Ja
Transferrate: 56.54 Mpps
Datenpaket-Pufferspeicher: 1.5 MB
Wärmeableitung: 41.602 BTU/h
Switch-Ebene: L3
Menge SFP-Modul-Steckplätze: 2
Zugriffkontrollliste: Ja
Anzahl Lüfter: 1 Lüfter
Versandkartonsbreite: 364 mm
Versandkartonslänge: 563 mm
Versandkartonshöhe: 379 mm
Gewicht (innerer) Versandkarton: 14640 g
Statische Anschlusssicherheit: Ja
SSH-/SSL-Unterstützung: Ja
Selbstlernen von MAC-Adressen unterstützt: Ja
Menge pro Versandkarton: 5 Stück(e)
Nettogewicht Versandkarton: 8042.5 g
Palettenbruttogewicht (Luft): 457700 g
Anzahl der Kartons pro Palette (Luft): 30 Stück(e)
Anzahl pro Palette (Luft): 150 Stück(e)
Palettenhöhe (Luft): 2030 mm
Palettenbruttogewicht (Meer): 457700 g
Anzahl der Kartons pro Palette (See): 30 Stück(e)
Anzahl pro Palette (See): 150 Stück(e)
Palettenhöhe (See): 2030 mm
Menge Modul-Steckplätze SFP+: 2
Anzahl der statischen Routen: 512
Physisches Stacking (Einheiten): 6
IGMP-Snooping: Ja
Virtuelles Stacking (Einheiten): 32

Brauchst du Hilfe?

Wenn Sie Hilfe mit D-Link DGS-1510 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Schalter D-Link

Bedienungsanleitung Schalter

Neueste Bedienungsanleitung für -Kategorien-