CyberPower PS900AVRLCD Bedienungsanleitung

CyberPower Nicht kategorisiert PS900AVRLCD

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower PS900AVRLCD (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

DETERMINE THE POWER

REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the

UPS does not exceed the UPS unit’s rated

capacity. If the rated capacities of the unit

are exceeded, an overload condition may

occur and cause the UPS unit to shut down

or the circuit breaker to trip.

the amount of power that your electronic

equipment will require. For optimal system

performance keep the load below 80% of

the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately

upon receipt. However, after receiving a

new UPS, to ensure the battery’s maximum

charge capacity, it is recommended that

you charge the

battery for at

least 8 hours.

Your UPS is

equipped with

an auto-charge

feature. When

the UPS is plugged into an AC outlet, the

battery will automatically charge whether

2. -

plugged, connect your computer, monitor,

and any other peripherals requiring battery

backup into the battery power supplied

outlets. Plug the other peripheral equip-

ment (e.g., printer, scanner, speakers, etc.)

into the full-time surge protection outlets.

DO NOT plug a laser printer, paper shred-

der, copier, space heater, vacuum cleaner,

sump pump, or other large electrical

device into the “Battery and Surge Pro-

tected Outlets.” The power demands of

these devices will overload and possibly

damage the unit.

3. To protect the network, connect a network

cable from the wall jack outlet to the IN

jack of the UPS. Then connect network

cable from the OUT jack on the UPS to the

computer or network device.

4. Plug the UPS into a 2 pole,

3 wire grounded receptacle

(wall outlet). Make sure the

wall branch outlet is pro-

tected by a fuse or circuit

breaker and does not service equipment

with large electrical demands (e.g., air con-

ditioner, refrigerator, copier, etc.). The war-

ranty prohibits the use of extension cords,

outlet strips, and surge strips in conjunction

with the UPS unit.

5. Press the power switch to turn the unit on.

The Power On indicator light will illuminate

green and the unit will “beep” once.

6. If an overload is detected, an audible alarm

will sound and the unit will emit one long

unplug at least one piece of equipment

from the battery power supplied outlets.

Make sure the circuit breaker is depressed

and then turn the UPS on.

7. To maintain optimal battery charge, leave

the UPS plugged into an AC outlet at all

times.

8. To store the UPS for an extended period

of time, cover it and store with the battery

fully charged. While in storage, recharge

the battery every three months to ensure

optimal battery life.

9. Ensure the wall outlet and UPS are locat-

ed near the equipment being attached for

proper accessibility.

YOUR ULTIMATE ALLY IN POWER

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

PS900AVRLCD

USER MANUAL

FEATURES

1. Power Switch

2. Power On Indicator

3. Mode Switch

4. USB Charging Ports

5. LCD Module Display

6. Battery and Surge Protected Outlets

7. Full-Time Surge Protected Outlets

8. Widely Spaced Outlets

9. Circuit Breaker

10. Coax Protection

11. Communication Protection Ports

CAUTION! To prevent the risk of fire or

electric shock, install in a temperature and

humidity controlled indoor area free of

conductive contaminants. (Please see

specifications for acceptable temperature

and humidity range).

CAUTION! To reduce the risk of electric

shock, do not remove the cover. There are

no user-serviceable parts inside.

CAUTION! Servicing of batteries should

be performed or supervised by personnel

knowledgeable of batteries and the required

precautions. Keep unauthorized personnel

away from batteries.

CAUTION! Hazardous live parts inside can be

energized by the battery even when the AC

input power is disconnected.

CAUTION! The UPS must be connected to an

AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is

not grounded. If you need to de-energize this

CAUTION! To avoid electric shock, turn

power source before installing a computer

component.

CAUTION! Not for use in a computer

room as defined in the Standard for the

Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

CAUTION! To reduce the risk of fire,

connect only to a circuit provided with

20 amperes maximum branch circuit over

current protection in accordance with the

National Electric Code, ANSI/NFPA 70.

CAUTION! DO NOT USE FOR MEDICAL

OR LIFE SUPPORT EQUIPMENT! DO NOT

operation and safety of life support equip-

ment, medical applications, or patient care.

CAUTION! DO NOT USE WITH OR NEAR

AQUARIUMS! To reduce the risk of fire

or electric shock, do not use with or near

an aquarium. Condensation from the

aquarium can cause the unit to short out.

CAUTION! DO NOT USE THE UPS ON ANY

TRANSPORTATION! To reduce the risk of

fire or electric shock, do not use the unit

on any transportation such as airplanes

caused during transit and the damp

environment can cause the unit to short out.

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructio carefully ns

during installation and operation of the unit. Read this manual thoroughly before attempting to

unpack, install, or operate your UPS.

INSTALLING YOUR UPS SYSTEM - continued

UNPACKING

Inspect the UPS upon receipt. The box should

contain the following:

(a) UPS unit

(b) User’s manual

AUTOMATIC VOLTAGE REGULATOR

The PS900AVRLCD sta lizbi es inconsistent utility

power to nominal lev that are safe fo quip-els r e

ment. Unstable u ty power can be damaging to tili

important data and hardware. With Automatic

Vo ge R ulation (AVR), damaging voltage lta eg

leve are corrected tls o safe levels. AVR auto-

matic increases low or decreases high u ity ally til

power to a consistent and safe 110/120 volts.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

1. Power Switch:

switch for equipment connected to the

battery power supplied outlets. To turn

the UPS ON, press the power button for

approximately 2 seconds - you will hear a

constant tone (1 second) - and release after

a short beep.

To turn the UPS OFF, press the power

button for approximately 2 seconds - you

will hear a constant tone (1 second) - and

release after two short beeps.

Alarm setting: The audible alarm can be

POWER button twice. The default setting

quickly press the power button twice. You

will hear two short beeps when the Alarm

quickly press the power button twice. You

will hear a single short beep when the

Alarm is turned On. *When the Alarm is

cation when the UPS reaches a low battery

state.

2. Power On Indicator: This LED is illuminated

when the utility power is normal and the

UPS outlets are providing power, free of

surges and spikes.

3. Mode Switch: Press the Mode Switch for

approximately 3 seconds to enter setup

mode to select three functions: Utility High

Voltage Range, Utility Low Voltage Range,

and LCD sleep ON/OFF. When a function is

selected, press Mode Switch for 3 seconds

to view options. When an option is select-

ed, wait for 8 seconds for the setting to

be confirmed. After the setting has been

confirmed, the LCD screen will leave setup

mode and go back to status display. If there

is no action for 8 seconds during setup,

the LCD will also leave setup mode and go

back to the status display.

a. Utility High Voltage Range: Adjust the

value of high voltage range.

b. Utility Low Voltage Range: Adjust the

value of low voltage range.

c. LCD: L1/L0 (ON/OFF):

* When LCD is set to L1, LCD will be

always ON. When LCD is set to L0, LCD

will dim if untouched for 1 minute.

* In battery mode, LCD is always on

regardless if the setting is L1 or L0.

4. USB Charging Ports: The USB Power ports

(Type A and Type C) provide DC 5V 2.1A

power output.

5. LCD Module Display: LCD display shows

all the UPS information using icons and

messages. For more information, please

review the “Definitions for Illuminated LCD

Indicators” section.

6. Battery and Surge Protected Outlets: The

unit has six battery powered and surge

protected outlets to ensure temporary

uninterrupted operation of your equip-

ment during a power failure. (DO NOT plug

a laser printer, paper shredder, copier,

space heater, vacuum cleaner, sump pump,

or other large electrical device into the

“Battery and Surge Protected Outlets.”

The power demands of these devices will

overload and possibly damage the unit.)

7. Full-Time Surge Protected Outlets: The

unit has six surge suppression outlets.

8. Widely-Spaced Outlets: The UPS unit

has four widely-spaced outlets. AC pow-

er adapters can be plugged into the UPS

without overlapping or blocking adjacent

outlets.

9. Circuit Breaker: Located on the side of the

UPS, the circuit breaker provides overload

and fault protection.

10. Coax Protection: The Coax/Cable/DSS

(RG6) protection ports will protect any

cable modem, CATV converter, or DSS

receiver.

11. Communication Protection Ports: Com-

munication protection ports (RJ11/RJ45)

will protect any standard modem, fax, or

telephone line.

3 4

576

PLUG IN

Additional troubleshooting information can be found at “Support” at www.CyberPowerSystems.com

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

TERMS AND CONDITIONS OF THE CYBERPOWER LIMITED WARRANTY

Please read the following terms and conditions carefully before using CyberPower products

(the “ Product”). By using the Product, you agree to be bound by the terms of this Limited

Warranty (collectively the “Warranty”). IF YOU DO NOT AGREE TO THE WARRANTY TERMS

AND CONDITIONS, YOU MUST RETURN THE PRODUCT BEFORE USING, AND OBTAIN A

FULL REFUND. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY

ALSO HAVE OTHER RIGHTS THAT VARY FROM ONE PLACE TO ANOTHER. YOUR ACCEP-

TANCE OF THIS WARRANTY MAY MODIFY OR WAIVE ANY OTHER RIGHTS YOU HAVE.

Cyber Power Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

CAUTION! This Product is not for use with aquariums, salt lamps, or any other water-related

products. To reduce the risk of ﬁre or electric shock, do not use with or near, water, water-re-

lated products, or any other liquid or source of moisture.

CAUTION! This Product is not for use with any high current ﬂow use including with applianc-

es, space heaters, or laser printers.

WARNING! Do not use for medical or life support equipment, for fail safe operations, or other

high-risk activities. This Product is not designed or intended for use in high-risk activities or

hazardous environments requiring fail-safe performance, including the operation of nuclear

facilities, aircraft navigation or communication systems, air trac control, weapons systems,

life support or medical applications or for use in any circumstance in which the failure of the

Product could lead directly to death, personal injury, or severe physical or property damage,

or that would aect operation or safety of any medical or life support device (collectively,

“High-Risk Activities”). CyberPower does not authorize use of any of its products in any High-

Risk Activities and CyberPower expressly disclaims any express or implied warranties for use

in High-Risk Activities. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT.

WHAT DOES THIS WARRANTY COVER?

This warranty covers defects in design, materials and workmanship in the Product under

normal use and conditions when installed and used in accordance with this manual. It does

not cover equipment that was connected to the Product and damaged because of the failure

of the Product. All implied warranties are disclaimed to fullest extent allowed by law, and in

any event, including any implied warranties of merchantability, ﬁtness for a speciﬁc purpose,

and quality are limited to the duration of the Warranty granted hereunder. This Warranty

only applies to consumers, and shall not apply in any commercial contexts absent express

contractual arrangements between CyberPower and the purchaser.

WHAT IS THE PERIOD OF COVERAGE?

This warranty covers the Product for three (3) years and the battery for two (2) years.

It does not cover equipment that was connected to the Product and damaged because of the

failure of the Product.

WHO IS COVERED?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise

transfer the Product.

WHAT IS NOT COVERED BY THE WARRANTY?

1. This Warranty does not cover any software that was damaged or needs to be replaced

due to the failure of the Product or any data that is lost as a result of the failure or the

restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: Products which are not defective or broken,

Products that are working as described in the user manual, any abnormal wear, misuse,

modiﬁcation, tampering, operation or storage outside environmental limits of the Product

or the equipment connected to it, damage while in transit or in storage, if there has been

improper operation or maintenance, or use with items not designed or intended for use

with the Product, such as laser printers, appliances, aquariums, medical or life support

devices, etc.

3. Damage when the Product was not installed or used in accordance with the user manual.

4. Damage when the Product is used contrary to any instructions provided with the Product,

or for any unintended or prohibited use.

WHAT ARE THE LIMITATIONS?

The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.

1. This Warranty does not apply unless the Product and the equipment that was connected

to it were connected to utility power via properly wired and grounded outlets (including

compliance with the most current electrical and safety codes), without the use of any

adapters or other connectors.

2. The Product must have been plugged directly into the power source and the equipment

connected to the Product must be directly connected to the Product and not “dai-

sy-chained” together in serial fashion with any other power strip, extension cords, another

Product or device similar to the Product, surge suppressor, power tap, or adapter. A three-

to two-prong adapter may not be used. Any such installation voids the Limited Warranty.

3. The Product and equipment connected to it must have been used properly in a suitable

and proper environment and in conformance with any license, instruction manual, or

warnings provided with the Product and the equipment connected to it.

4. The Product must have been used at all times within the limitations on the Product’s VA/

Wattage capacity.

5. CyberPower’s obligation is reduced by any amounts that the Initial Customer is entitled

to recover from other sources, including insurance, other warranty, or extended warranty

coverage, whether or not the Initial Customer makes a claim for recovery.

6. The Product was designed to eliminate disrupting and damaging eects of momentary

(less than 1ms) voltage spikes or impulses from lightning or other power transients. If it can

be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence will be

deemed outside the rated capabilities of the Product and the Limited Warranty is void.

CYBERPOWER DOES NOT COVER OR UNDERTAKE ANY LIABILITY IN ANY EVENT FOR

ANY OF THE FOLLOWING:

1. Loss of or damage to data, records, or software or the restoration of data or records, or the

reinstallation of software.

2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly

installed, grounded and code-compliant 120 volt power lines; transients, surges or spikes on

standard telephone land lines, PBX telephone equipment lines or Base 10T Ethernet lines,

when properly installed and connected. (This exclusion applies, for example, to fluctuations in

data transmission or reception, by CATV or RF transmission or fluctuations, or by tran-sients

in such transmission.)

3. Damage from any circumstance described as excluded above with respect to the Product.

4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse,

misuse or alteration of either the Product or the equipment to which it is connected.

5. CyberPower excludes any liability for personal injury under the Limited Warranty.

CyberPower excludes any liability for direct, indirect, special, incidental or consequential

damages, whether for damage to or loss of property, loss of profits, business interruption, or

loss of information or data.

6. The Product is not for use in high-risk activities or with aquariums. The Product is not

designed or intended for use in hazardous environments requiring fail-safe performance, or

for use in any circumstance in which the failure of the Product could lead directly to death,

personal injury, or severe physical or property damage, or that would affect oper-ation or

safety of any medical or life support device (collectively, “High Risk Activities”). CyberPower

expressly disclaims any express or implied warranty of fitness for High Risk Activities or with

aquariums. CyberPower does not authorize use of any Product in any High Risk Activities or

with Aquariums. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT.

WHERE CAN I GET MORE INFORMATION?

CyberPower is the warrantor under this Limited Warranty. For further information please

55379; call us at (877) 297-6937 or (800) 279-6580; or send us an e-mail message at

lac.service@cyberpower.com.

HOW DO I OBTAIN WARRANTY SERVICE?

Please return the Product, along with your purchase receipt, to the retailer from which it was

purchased, and they will issue you a replacement product or a refund.

Please check our website at yber ower .com for additional information on www.C P Systems

the warranty.

This Warranty is governed by and shall be interpreted under the laws of the United States and

the State of Minnesota, without reference to conflict of law principles. The parties agree that

the United Nations Convention on Contracts for the International Sale of Goods shall not

apply. Unless prohibited by law, any action to enforce the terms of this Warranty or for any

other claim you may have associated with the product, shall be brought in the State or

Federal Court serving Scott County, State of Minnesota, United States of America and the

parties expressly consent to jurisdiction in that venue. However, before bringing a claim for a

breach of a warranty, a claimant shall pursue a Warranty Claim with CyberPower as set forth

in this Warranty. Thereafter, the parties shall resolve their dispute by binding arbitration. Any

controversy or claim arising out of or relating to this contract, or the breach thereof, shall be

settled by arbitration administered by the American Arbitration Association in accordance

with its Consumer Arbitration Rules and judgment on the award rendered by the arbitrator

may be entered in any court having jurisdiction thereof. Claims shall be heard by a single

arbitrator. The place of arbitration shall be Minneapolis, Minnesota, United States and shall be

governed by the laws of the State of Minnesota. Hearings will take place pursuant to the

standard procedures of the Consumer Arbitration Rules that contemplate in person hearings.

The arbitrators will have no authority to award punitive or other damages not measured by

the prevailing party’s actual damages, except as may be required by statute. The arbitrator

shall not award consequential damages in any arbitration initiated under this section. Any

award in an arbitration initiated under this clause shall be limited to monetary damages and

shall include no injunction or direction to any party other than the direction to pay a monetary

amount. Each party shall bear its own costs and expenses and an equal share of the arbitra-

tor’s and administrative fees of arbitration. The award of the arbitrator shall be accompanied

by a reasoned opinion. Except as may be required by law, neither a party nor an arbitrator

may disclose the existence, content, or results of any arbitration hereunder without the prior

written consent of both parties. The parties agree that failure or refusal of a party to pay its

required share of the deposits for arbitrator compensation or administrative charges shall

constitute a waiver by that party to present evidence or cross-examine witness. In such event,

the other party shall be required to present evidence and legal argument as the arbitrator may

require for the making of an award. Such waiver shall not allow for a default judgment against

the non-paying party in the absence of evidence presented as provided for above. PLEASE

VISIT WWW.CYBERPOWERSYSTEMS.COM FOR A COPY OF THE

LIMITED WARRANTY.

Where Can I Get More Information?

The application of the United Nations Convention of Contracts for the International Sale of

Goods is expressly excluded. CyberPower is the warrantor under this Limited Warranty. For

further information please feel free to contact CyberPower at:

Cyber Power Systems (USA), Inc.

4241 12th Ave E., STE 400, Shakopee, MN 55379;

Call us at (877) 297-6937; or submit a web ticket online at cyberpowersystems.com/support.

WARNING: This product can expose you to chemicals including bisphenol A (BPA) and

styrene, which is known to the State of California to cause reproductive harm and cancer.

For more information, go to www.P65Warnings.ca.gov.

CyberPowerSystems.com

Power Systems (USA) Inc.

LIMITED WARRANTY

7 8

SYSTEM FUNCTION BLOCK DIAGRAM

Input OutputEMI Fllter Surge

Suppressor AVR

LIA Battery Inverter

Normal Mode

Battery Mode

Problem Possible Cause Solution

Full-time surge protection

outlets stop providing

power to equipment. Circuit

breaker button is projecting

from the side of the unit.

Circuit breaker has tripped due to an

overload.

Turn the UPS off and unplug at least one piece

of equipment. Wait 10 seconds, reset the circuit

breaker by pressing the button, and then turn the

UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged. Recharge the battery by leaving the UPS

plugged in.

Battery is worn out. Contact CyberPower about replacement batteries.

The UPS will not turn on.

The on/off switch is designed to prevent

damage from rapidly turning it off

and on.

Turn the UPS off. Wait 10 seconds and then turn

the UPS on.

The unit is not connected to an AC outlet. The unit must be connected to a 120V 50/60Hz

outlet.

The battery is worn out. Contact CyberPower about replacement batteries.

Mechanical problem. Contact CyberPower.

The frequency is outside of the operating

range of 45-65Hz.

Turn the UPS off. Make sure the frequency range

is within 45-65Hz. Or you can turn the UPS on in

battery mode.

1. INPUT Voltage Meter: This meter measures

the AC voltage that the UPS system is

receiving from the utility wall outlet. The

UPS is designed to continuously supply

connected equipment with stable output

voltage. In the event of a complete power

loss, severe brownout, or over-voltage,

the UPS relies on its internal battery to

supply consistent 110/120 output voltage.

The INPUT voltage meter can be used as

a diagnostic tool to identify poor-quality

input power.

2. OUTPUT Voltage Meter: This meter

measures, in real time, the AC voltage

that the UPS system is providing to the

computer during normal AC/Utility Power

mode, and battery backup mode.

3. ESTIMATED RUNTIME: This displays the run

time estimate of the UPS with the current

battery capacity and load.

4. NORMAL Icon: This icon appears when the

UPS is working under normal conditions.

5. BATTERY icon: During a severe planned

power suppression or power outage, this

icon appears and an alarm sounds (two

short beeps followed by a pause) to indicate

the UPS is operating from its internal

batteries. During a prolonged planned

power suppression or power outage, the

alarm will sound continuously to indicate

the UPS’s batteries are nearly out of power.

You should save files and turn off your

equipment immediately.

6. SILENT MODE icon: This icon appears

whenever the UPS is in silent mode.

7. OVERLOAD icon: This icon appears and

an alarm sounds to indicate the battery-

supplied outlets are overloaded. To clear the

overload, unplug some of your equipment

from the battery-supplied outlets until the

icon turns off and the alarm stops.

8. BATT. CAPACITY meter: This meter displays

the approximate charge level of the UPS's

internal battery in 25% increments. During

a blackout or severe brownout, the UPS

switches to battery power (the BATTERY

icon appears) and the battery charge level

decreases.

9. LOAD CAPACITY meter: This meter displays

the approximate output load level of the

UPS battery outlets in 25% increments.

10. FAULT icon: The following number appears

if there is a problem with the UPS. Press the

POWER button to turn the UPS off.

E22: Battery Mode or AC/Utility Power

Mode Overload fault (Unplug at least one

piece of equipment from battery outlets

and turn the UPS on again.)

E21: Battery Output Short fault (Unplug at

least one piece of equipment from battery

outlets and turn the UPS on again.)

E01: Charger Fault (Contact CyberPower

for support)

E24: Internal Fault (Contact CyberPower

for support)

E03: AVR Mode over temperature

protection (Press the power button to

turn off unit. Unplug at least one piece of

equipment and wait for 30 minutes.

Press the power button to turn on unit.)

Model PS900AVRLCD

Capacity 900VA / 500W

Nominal Input Voltage 120 VAC

Input Frequency 50/60 Hz ± 5 Hz

On-Battery Output Voltage 120 VAC ± 10%

Automatic Voltage Regulator (AVR) Single Boost / Single Buck

On-Battery Output Frequency 50/60 Hz ± 1 Hz

Max. Load for UPS Outlets 900VA / 500W

Max. Load for Full-Time Surge Protection Outlets 12 Amp

On-Battery Output Wave Form Simulated Sine Wave

Operating Temperature + 32°F to 104° F / 0° C to 40° C

Operating Relative Humidity 0 to 90% non-condensing

Size (W x H x D) 12.2" x 7" x 3.5"

Net Weight 5.4 kg

Battery Type CyberPower / RBP0089

Typical Battery Recharge Time 4 hours to 90% capacity from complete discharge

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals RETIE

Advanced Energy-Saving Patented Bypass Technology

CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy costs by up to 75% compared to conventional

UPS models. Even when utility power is normal, conventional UPS models constantly pass power through a transformer. By contrast,

under normal conditions the advanced circuitry of a GreenPower UPS™ bypasses the transformer. As a result, the power eciency is

signiﬁcantly increased while decreasing waste heat, using less energy, and reducing energy costs. When an abnormal power condition

occurs, the GreenPower UPS™ automatically runs power through its transformer to regulate voltage and provide “safe” power.

Since utility power is normal over 88% of the time, the GreenPower UPS™ operates primarily in its ecient bypass mode. The GreenPower

UPS™ is also manufactured in accordance with the Restriction on Hazardous Substances (RoHS) directive making it one of the most

environmentally-friendly on the market today.

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

GREEN

POWER UPS

™

Energy-Saving Technology

POWER ALARM

CONDITION

On Off Normal

On Beep twice

every 30 seconds

Utility Failure - The UPS is providing power to battery power-supplied

outlets from its battery.

On Rapid beeping

every 1/2 second

Utility Failure - The UPS is providing battery power. Rapid beeping

indicates the unit will run out of power soon.

On/Off Constant tone

Battery Mode or AC/Utility Power Mode Overload Fault - Occurs

when connected equipment exceeds the rating of battery outlets of the

unit. Please unplug at least one piece of equipment from battery outlets.

Off Constant tone

Battery Output Short Fault - Please unplug at least one piece of equip-

ment from battery outlets and turn on the UPS again. If the fault still

exists, please contact CyberPower Systems for support.

On Constant tone Charger Fault - Contact CyberPower Systems for support.

DEFINITIONS FOR LED INDICATORS & AUDIBLE ALARMS

The LCD display indicates a variety of UPS

operational conditions. All descriptions apply

when the UPS is plugged into an AC outlet

and turned on or when the UPS is on battery.

K01-0000999-00

Produktspezifikationen

Marke:	CyberPower
Kategorie:	Nicht kategorisiert
Modell:	PS900AVRLCD

Brauchst du Hilfe?

Wenn Sie Hilfe mit CyberPower PS900AVRLCD benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert CyberPower

CyberPower Rackbar RKBS20ST6F12R Bedienungsanleitung

13 Oktober 2024

CyberPower Rackbar RKBS20ST6F8R Bedienungsanleitung

7 Oktober 2024

CyberPower RMCARD305 Bedienungsanleitung

4 Oktober 2024

CyberPower SB0602BA-DE-B50 Bedienungsanleitung

24 September 2024

CyberPower SB0802AD-DE-W24 Bedienungsanleitung

24 September 2024

CyberPower SB0502BA-DE-B70 Bedienungsanleitung

24 September 2024

CyberPower SB0502BA-DE-W70 Bedienungsanleitung

24 September 2024

CyberPower SB0702AD-DE-B30 Bedienungsanleitung

24 September 2024

CyberPower SB0602BA-DE-W18 Bedienungsanleitung

24 September 2024

CyberPower SB0702AD-DE-W30 Bedienungsanleitung

24 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024