CyberPower DTC50U12V Bedienungsanleitung

CyberPower Nicht kategorisiert DTC50U12V

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower DTC50U12V (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

User’s Manual for

CyberShield

DTC50U12V3

CyberShield UPSs are designed to provide a local power solution for

cable telephony, wireless local loop (WLL), and fiber to the home

(FTTH) broadband equipment.

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

INSTALLATION

OVERVIEW

DESKTOP USE:

1.) Open the battery door at the back of the DTC50U12V3 and connect the battery wires.

2.) Plug AC power cable into wall outlet.

3.) Connect the communication cable and simply place the DTC50U12V3 unit on or

underneath desk to begin backing up the optical home network.

BATTE REPLACEMENTRY

As long as utility power is on, you may leave the UPS and connected equipment on while replacing a new

battery. (For service personnel reference only)

COLD START

Step 1:

Connect the AC cable to the wall outlet.

Step 2:

Connect the communication cable between the DTC50U12V3

and the ONT device.

Step 1:

a. Slide off the battery

cover at the back of the

DTC50U12V3 unit.

Step 2:

a. Remove the battery from

the enclosure.

b. Disconnect both battery

cable connectors.

Step 3:

a. Install the new battery by connecting

the red lead to the positive terminal

and the black lead to the negative

terminal.

b. Slide the battery back into the

compartment.

c. Replace battery cover to resume

normal operation.

Step 3:

Install the cable retainer to secure the

commnication cable.

Step 4:

Use the enclosed wall mount template to locate screws on the

wall. Hang the DTC50U12V3 on the screws which are located

on the wall.

The cold start feature is to supply power to the UPS and connected equipment when the UPS

shuts down and no utility power is available. Before using the cold start feature, please make sure

that the battery is properly charged. To turn on the cold start feature, please press and hold the

cold start button until 4 LED indicators light up.

This manual contains important instructions regarding the installation and operation of this device.

Read this manual thoroughly before attempting to unpack, install or operate this device.

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is

disconnected.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity

controlled indoor area, free of conductive contaminants. (Please see specifications for

acceptable temperature and humidity range.)

CAUTION! To reduce the risk of electric shock, do not remove the cover. No user serviceable

parts inside include battery. Please contact our company or our dealer directly.

CAUTION! When replacing batteries, the replacement should have the same rating as follows,

Listed/Certified Valve Regulated Lead Acid Battery, 12V, max. 9Ah.

CAUTION! Ri nerg Ha ard ba ersk f Eo y z , tt y. B tt , cef c ore repla ing ba eries remove onduc jewelrtive y

s a th s t uch s c s, st tc s, hain wri wa he and rings and use ools wi t in ula ed handle Highs.

energ hrough condu ive ma erials ould cau e severe burny t ct t c s s.

CAUTION! Do not dispose of batteries in a fire. The battery may explode if improperly disposed.

Recycle batteries in accordance with local regulations.

CAUTION!

Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It

may be toxic.

The UPS battery is charged when it is connected to utility power. The battery is fully

charged during the first of normal operation. Do not expect full battery run 24 hours

capability during this initial charge period.

ALARM SILENCE

The audible alarm will be enabled when the unit is operating from battery or battery power is low.

Press the Alarm Silence button for 0.5 seconds, the unit will beep once confirming that audible

alarms have been temporary disabled for 24 hours. Press this button one more time for 0.5 seconds

to enable audible alarms again. The unit will beep twice confirming that audible alarms have been

enable. Or press and hold the Alarm Silence button for 15 seconds the units will beep once confirm

ing that audible alarms have been disabled permanently. To restore the audible alarm, press and

hold the Alarm Silence button for 15 seconds and the unit will beep twice confirming that audible

alarms have been enabled.

WALL MOUNT USE:

8LED Indicator

Alarm Silence Button

Cold Start Button

Cable Retainer Installation Point

Communication Cable Connector

AC Power Cable Connector

Battery Cover

External Battery Connector

LED INDICATOR

BATTERY

SYSTEM

S TUSTA

MUTE

Green

Orange

Red

Indicates normal mode of operation.

Indicates the battery is supplying the power. At 45% battery capacity,

the LED will flash and then alarm will beep 4 times per minute.

Press and hold the button “Alarm Silence” for 0.5 seconds to silence

the audible alarm for 24 hours, and the LED will flash.

Battery replacement required. Alarm will beep once every 15 minutes.

The LED also illuminates when battery is absent.

The recommended capacity of an external battery is less than 100Ah. External batteries

should be fully charged before used.

Indicator Color Condition

Number Description

COMMUNICATION SIGNALS

12V

12V RTN

SIG RTN

ON BATTERY

BATTERY MISSING

REPLAC AE B TTERY

LOW BATTERY

+ Vol aget ou put t

- Vol aget output

S ignal return

Low when operating rom f utility . line

Low when ba erytt i s fnear ull charge apa c city.

O pen when opera ing romt f a th ba er witt y < 45% capacity.

SignalPin Message

LIMITED WARRANTY

CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years from the date of original purchase, subject to the terms of this Limited

Warranty. This Limited Warranty gives you specific rights, and you may have other rights, which vary from State to State or Province to Province.

Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to three years. This provision shall NOT create any Implied Warranty or

Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product. NOTE: Some States and Provinces do not allow limitations on how long an implied warranty lasts,

so the above limitation may not apply to you.

To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty. Your sole and exclusive remedies are those provided by this

Limited Warranty. This exclusion of other express warranties applies to written and oral express warranties. CyberPower excludes any liability for personal injury. CyberPower excludes any liability for direct,

indirect, special, incidental, or consequential damages, whether for damage to or loss of property, loss of profits, business interruption, information or data. This exclusion applies even though damage or loss

is caused by negligence or other fault. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.

DO NOT USE FOR MEDICAL OR LIFE SUPPO EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.RT

CyberPower does not sell the PRODUCT for use in high-risk activities. The PRODUCT is not designed or intended for use in hazardous environments requiring fail-safe performance, including the operation

of nuclear facilities, aircraft navigation or communication systems, air traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the PRODUCT

could lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life support device (collectively, "High Risk Activities").

CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities. CyberPower does not authorize use of any PRODUCT in any High Risk activities.

ANY SUCH USE IS IMPROPER AND IS MISUSE OF CYBERPOWER PRODUCT. A A

The Limited Warranty is governed by the laws of the United States and the State of Minnesota, without reference to conflict of law principles. The application of the United Nations Convention of Contracts for

the International Sale of Goods is expressly excluded.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1)Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an

experienced radio/TV technician for help.

CAUTION: Shielded signal cables must be used with this device to ensure compliance with Class B FCC limits.

CAUTION: Any changes or modifications not expressly approved by Cyber Power could void the authority granted by the FCC to operate this equipment.

AC Inlet

Communication signals

The communication signals of this unit are isolated from the internal circuitry via open

collector opto-coupled transistors. The connection “SIG RTN” (Signal Return) is a common

return point for all communication signals. In the typical application, the attached equipment

digital ground connects to Signal Return, and pull-up resistors turn the open collector

signals into logic levels.

DTC50U12V3

K01-5012000-00

SPECIFICATION

Input

Voltage Range

100Vac - 240Vac

Frequency Range

50-60Hz

Output

On Battery Output Voltage

12Vdc

Continuous Power Capability

50W

Efficiency ( Max Load )

≥ 80%

Battery

Battery Type

Sealed, Maintenance Free Lead-Acid Battery

Numbers of Battery

12Vdc / 9AH x 1

Typical Recharge Time

20 Hours . (90% Charged)

Yes

Replaceble

Surge Protection and Filtering

Lightning / Surge Protection

Yes

Management

Battery Auto-Charge

Yes

cPhysi al

Dimensions (LxWxD)

18.6cm x 8.2cm x 18.5cm

Weight (Net)

3. kg (with 9AH battery)37

Environment

Operating Temperature

32ºF - 104ºF

Operating Humidity

0 – 95% noncondensing within enclosure

Max Operating Elevation

10,000ft (3,050m)

Max Storage Elevation

50,000ft (15,000m)

St age Tor emperature

Pin 1 Pin 8

32ºF - 113ºF

Low when battery is present.

Open when battery is missing/fails the self-test.

For more information, please contact:

CyberPower Systems ( USA ), Inc. 4241 12th Avenue East, Suite 400, Shakopee, MN55379 Phone: (952)403-9500 Fax: (952)403-0009 www.cyberpowersystems.com

CyberPower Systems ( EUROPE ), Inc. www.cyberpowersystems.com

External Battery

Connector

EXTERNAL BATTERY