CyberPower DTC36U12V3-G Bedienungsanleitung

CyberPower Nicht kategorisiert DTC36U12V3-G

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower DTC36U12V3-G (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

User’s Manual for

CyberShield

DTC36U12V3-G

OVERVIEW

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and operation of this device.

Read this manual thoroughly before attempting to unpack, install, or operate this device.

CAUTION!

CyberShield UPSs are designed to provide a local power solution for

cable telephony, wireless local loop (WLL), and fiber to the home

(FTTH) broadband equipment. FTTx not only needs backup power

to prevent utility power failure, but also supports making emergency

calls (e.g., 911) for help.

The battery can energize hazardous live parts inside even when the AC input power

is disconnected.

Before replacing the battery, make sure the replacement has the same rating:

Certified Valve Regulated Lead Acid Battery, 12V, 7.2Ah maximum.

CAUTION!

To reduce the risk of electric shock, keep the cover on. There are no user-serviceable

parts inside the unit. Please contact us or our dealer for service.

Before replacing the battery, remove conductive jewelry, such as chains, watches and ,

rings. Use tools with insulated handles to avoid high energy, which could pass through

conductive materials and cause severe burns.

To avoid electric shock, unplug power cable from the AC power source before servicing

the battery or installing a computer component.

It is recommended to connect the unit to the required equipment and battery before

plugging in the utility power.

The UPS battery is charging when it’s connected to utility power. The battery is

charging during its first 24 hours of normal operation. Don’t expect full battery capacity

during this initial charging period.

The battery must be supplied by CyberPower. Using improper battery which is not

evaluated with this model could cause a risk and is at the user's own risk.

To store the UPS for an extended period, refer to the typical recharge time in the

specification and recharge the battery every three months to ensure battery life.

To reduce the risk of fire or electric shock, install in an indoor area that both temperature

and humidity could be controlled, and free of conductive contaminants. To find the

acceptable ranges of temprature and humidity, please refer to the specification.

Runtime is based on testing fully-charged and new batteries at normal operating

conditions. Runtime curve is approximate and varies based on battery age, level of

charge at test, environment, and other variables.

Number

Description

Alarm Silence Button

Cold Start Button

Cable Retainer Installation Point

Communication Cable Connector

AC Power Cable Connector

Battery Cover

LED Indicator

INSTALLATION

DESKTOP USE:

1.) Remove the battery cover at the back of the DTC36U12V3 and connect the battery wires.

2.) Connect the communication cable and simply place the DTC36U12V3 on or under a desk to

begin backing up the optical home network.

3.) Plug the AC power cable into wall outlet.

4.) DTC36U12V3 desktop placement is shown as OVERVIEW illustration.

Step 3:

Connect the AC cable to the wall outlet.

Step 2:

a. Connect the communication cable between the DTC36U12V3

and the ONT device.

b. Install the cable retainer to secure the commnication cable.

WALL MOUNT USE:

RECOMMENDED SCREW SIZE

Mounting Surface

1"~1.5"

1/8"

3/16"

5/16"

Step 1:

b. Place the screws into the wall using and required anchors for a secure installation.

c. Place the round portion of the keyhole slots of the unit over the installed mounting screws.

d. Connect the battery connector carefully, reinstall the battery into the unit and secure the strap.

a. Use the enclosed installation paper template to mark the location of the screw holes used to mount the DTC36U12V3 to the wall.

BATTERY REPLACEMENT

As long as utility power is on, you may leave the UPS and connected equipment while replacing a new

battery. (For service personnel reference only)

Step 1:

a. Slide off the battery cover

at the back of the unit.

Step 2:

a. Remove the battery from the enclosure.

b. Disconnect the battery cable connectors.

Step 3:

a. Replace with new battery and reconnect the

battery connector. Make sure the red wire

is connected to the “+” polarity, and the

black wire is connected to the “-” polarity.

b. Slide the battery back into the compartment

and cover the unit.

COLD START

BUTTON FUNCTIONS

The cold start feature is used when utility power is no longer present and a new or fresh

battery is installed to support the load device. Once the new/charged battery is installed,

depress the COLD START button until the 4 LED indicators light up.

Functions

Cold Start Press the COLD START button for 3 seconds.

Reset Output

Instructions

Temporarily Alarm

On/Off

Permanent Alarm

On/Off

Press the ALARM SILENCE button for 1 second to turn the alarm off

for 24 hours. A short beep will occur to confirm the alarm is off.

Press the

ALARM SILENCE

button for 15 seconds to turn the alarm off

for permanently. A short beep will occur to confirm the alarm is off.

Press the ALARM SILENCE button for 1 second again to restore the

alarm. Two short beeps will occur to confirm the alarm is on.

Press the

ALARM SILENCE

button for 15 seconds again to restore the

alarm. Two short beeps will occur to confirm the alarm is on.

Press the

ALARM SILENCE

button for 20 seconds to turn off the

output power, and it will turn on automatically after 15 seconds.

CAUTION! The means of power cord should be connected to a socket-outlet with earthing connection.

AC Inlet

Communication signals

DTC36U12V3

Pin 7

Indicator Color Light on

BATTERY

SYSTEM

STATUS

MUTE

Green

Orange

Red

LED STATUS INDICATION

Normal operation

Light off

System fault

(Output off)

Battery mode Utility mode

Blinking

Permanent alarm off Alarm on Temporarily alarm off

Replace battery/

Battery missing

Low battery

Battery OK N/A

N/A

COMMUNICATION SIGNALS

The communication signals of this unit are isolated from the internal circuitry via open collector

optocoupler transistors. The connection “SIG RTN” (Signal Return) is a return point for all

communication signals. In the typical application, the connected equipment digital ground

connects to Signal Return, and pull-up resistors turn the open collector signals into logic levels.

12V

12 V R T N

RTN

ON BATTERY

BATTERY MISSING

REPLACE BATTERY

LOW BATTERY

Signal return

Low when the UPS is in utility mode.

Low when battery has sufficient capacity.

Open when the battery’s capacity is low.

SignalPin Message

Low when battery is present.

Open when battery is missing or needs to be replaced.

12 Volt power return

Open when the UPS is in battery mode.

+ Voltage output

SIG

Low when the battery is in a normal state.

Open when the battery needs to be replaced.

SPECIFICATION

Input

Voltage Range

Frequency Range

Output

On Battery Output Voltage

12 Vdc

Continuous Power Capability

36 W

≥ 80%

Battery

Battery Type

Sealed, Maintenance Free Lead-Acid Battery

Numbers of Battery

12 Vdc / 7.2 AH x 1

Typical Recharge Time

14 hours

Yes

Replaceble

Surge Protection and Filtering

Lightning / Surge Protection

Yes

Management

Auto Charge

Yes

cPhysi al

Dimensions (L*W*D)

16.8 cm x 8.1 cm x 18.5 cm

Weight (with battery)

3.13 kg

Environment

Operating Temperature

- 4ºF

–

113ºF

Operating Humidity

0 – 95% noncondensing within enclosure

Max Operating Elevation

10,000 ft (3,048 m)

Max Storage Elevation

50,000 ft (15,240 m)

Storage Temperature

(-20

ºC

–

45ºC)

100 Vac

–

240 Vac

–

60 Hz

Efficiency (at Full Load, 25°C)

(25°C)

Maximum Full Charge Time (25°C)

DTC36U12V3Model

36 hours

- 4ºF

–

113ºF

(-20

ºC

–

45ºC)

For more information, please contact:

CyberPower Systems ( USA ), Inc. 4241 12th Avenue East, Suite 400, Shakopee, MN 55379 Phone: (952)403-9500 Fax: (952)403-0009 cyberpowersystems.com

CyberPower Systems ( EUROPE ), Inc. Flight Forum 3545, 5657DW Eindhoven, The Netherlands E-mail: sales@cyberpower-eu.com eu.cyberpowersystems.com

K01-3612009-02

WARNING: Cancer and Reproductive Harm-

www.P65Warnings.ca.gov.

LIMITED WARRANTY

The Limited Warranty is governed by the laws of the United States and the State of Minnesota, without reference to conflict of law principles. The application of the United Nations Convention of Contracts

for the International Sale of Goods is expressly excluded.

FCC NOTICE

CAUTION: Shielded signal cables must be used with this device to ensure compliance with Class B FCC limits.

CAUTION: Any changes or modifications which are not expressly approved by CyberPower could void the authority granted by the FCC to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or

relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

(4) Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Batteries are considered HAZARDOUS WASTE , so they must be disposed of properly.

Most retailers that sell lead-acid batteries collect used batteries for recycling, as required by local regulations.

CAUTION: CyberPower Systems encourages environmentally sound methods for disposal and recycle of its UPS products.

Please dispose and/or recycle the UPS in accordance to the local regulations of your state.

CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years from the date of original purchase, subject to the terms of this Limited

Warranty. This Limited Warranty gives you specific rights, and you may have other rights, which vary from State to State and Province to Province.

Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to three years. This provision shall NOT create any Implied Warranty or

Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product. NOTE: Some States and Provinces do not allow limitations on how long an implied warranty lasts,

so the above limitation may not apply to you.

To be covered, you must be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty. Your sole and exclusive remedies are those provided by this Limited

Warranty. This exclusion of other express warranties applies to written and oral express warranties. CyberPower excludes any liability for personal injury. CyberPower excludes any liability for direct, indirect,

special, incidental, or consequential damages, whether for damage to or loss of property, loss of profits, business interruption, information or data. This exclusion applies even though damage or loss is

caused by negligence or other faults. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to

you.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.

CyberPower does not sell the Product for use in high-risk activities. The Product is not designed or intended for use in hazardous environments requiring fail-safe performance, including the operation of

nuclear facilities, aircraft navigation or communication systems, air traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the Product could

lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life support device (collectively, "High Risk Activities").

CyberPower

expressly disclaims any express or implied warranty of fitness for High Risk Activities. CyberPower does not authorize the use of any Product in any High Risk Activities. ANY SUCH USE IS IMPROPER

AND IS A MISUSE OF A CYBERPOWER PRODUCT.

Pin 1