CyberPower Doorsensor Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower Doorsensor (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Package Contents
Installation Guide
Step 1. Wire the DOORSENSOR to an ENVIROSENSOR
(sold separately) as shown below. One wire
connects to any of the Dry Contact Input terminals
(1-4) and the remaining wire connects to the COM
terminal.
Rack Enclosure Front Door
Rack Enclosure Rear Door
NOTE: The DOORSENSOR should be mounted on the opening
end of the enclosure door (opposite side of the hinges).
The magnet should be mounted flush against the inside
edge of the door. Align the switch with the magnet
mounted on the enclosure door and adhere it to the
outside of the enclosure frame where the door closes.
(1) Door Switch Sensor with 10ft (3m) Cable
(6) Cable Ties
(3) Adhesive Cable Tie Holders
(6) (M2x10) Screws
(Two are spare)
Normal Door
NOTE: The DOORSENSOR should be mounted on the opening
end of the door (opposite side of the hinges).
321 4
COM
Copyright © 2016 Cyber Power Systems, Inc. All rights reserved.
USER’S MANUAL
SAVE THESE INSTRUCTIONS
Please read this manual and follow the instructions for installation and use.
K01-0000444-01
Step 2. Clean the surface of the area where the sensor will
be installed.
Step 3. Remove the protective strip behind the sensor to
expose the adhesive tape backing. Place the sensor
on the desired location and press firmly for 30
seconds.
Magnetic Door Switch SensorMagnetic Door Switch Sensor
DOORSENSOR
RECON SERIESRECON SERIES
Switch
Magnet
Switch Magnet
Appendix
1. When the door is closed, the DOORSENSOR should be
aligned and the distance (gap) between the switch and
magnet should be less than 1/4" (6mm), as shown
below.
Less than 1/4 inch (6 mm)
O X
2. The ENVIROSENSOR Contact settings configured via
the connected RMCARD or PDU need to be changed to
"Normally Closed" in order for a closed door to be
monitored as such. See respective RMCARD or PDU
User Manual for more information.
For warranty and additional information, please visit:
www.cyberpower.com.
Contact
#1 Name & State
#2 Name & State
#3 Name & State
#4 Name & State
Apply Reset
DOORSENSOR
Contact#2
Contact#3
Contact#4
Normally Closed
Normally Open
Normally Open
Normally Open
(Optional) Use the included cable ties and adhesive
backed cable tie holder to secure the DOORSENSOR
cables.
(Optional) Drill 5/8" (1.6mm) holes where the
DOORSENSOR switch and magnet will be mounted on
the door frame and door.
Cyber Power Systems, Inc.
www.cyberpower.com
For USA and Canada:
4241 12th Ave East, Suite 400
Shakopee, MN 55379
Toll-free: (877) 297-6937
For all other regions:
Please visit our website for local contact information.


Produktspezifikationen

Marke: CyberPower
Kategorie: Nicht kategorisiert
Modell: Doorsensor

Brauchst du Hilfe?

Wenn Sie Hilfe mit CyberPower Doorsensor benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert CyberPower

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-