CyberPower CyberShield CBN50U48A-1 Bedienungsanleitung

CyberPower UPS CyberShield CBN50U48A-1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower CyberShield CBN50U48A-1 (2 Seiten) in der Kategorie UPS. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

User’s Manual for

CyberShield

CBN50U48A-1

CyberShield UPSs are designed to provide a local power solution for

cable telephony, wireless local loop (WLL), and fiber to the home

(FTTH) broadband equipment.

ENCLOSURE INSTALLATION

Carefully follow these instructions during installation of this device:

1.) Carry out the installation in a safe area that is free of excessive dust and has adequate airflow.

2.) Screws must be appropriate for total weight of the UPS and the mounting surface material.

3.) Do not operate the UPS where the temperature and humidity are outside the specified limits.

(Refer to specification in this manual.)

BATTERY REPLACEMENT

This battery is hot-swappable. As long as utility power is on , you may leave the UPS and connected

equipment on while replacing a new battery.

Once the battery is disconnected, the connected equipment is not protected from power

outages.

Deliver spent batteries to a recycling facility or ship to the manufacturer in the

replacement battery packing material.

WARNING INDICATOR

OPERATION

Connect: Equipment and Power

Step1. Plug the UPS power cord into the utility power cord inlet

Step2. Plug the UPS power cord into the wall outlet.

COLD START

The cold start feature is for applying power to the UPS and connected equipment when the UPS is

off and there is no utility power. Before using the cold start feature, please make sure the battery is

charged. To start the cold start feature, press the recessed cold start button with a small pointed

object.

UPS is on utility power.

UPS is on battery power.

DC output power is provided by the battery or

utility power.

The battery is not connected or the battery

needs to be replaced.

Green

Yellow

Green

Red

Indicator

Step 1:

a. Remove the battery cover.

Step 2:

a. Unstrap strap from battery.

b. Slide battery off of the shelf.

c. Disconnect battery cable

connector at chassis end.

Step 3:

a. Use the enclosed installation template to

mark an installation location for the unit.

b. Mount the unit on the wall with 2 mounting

screws into the keyhole slots.

c. Tighten the screws to secure the units.

d. Connect the battery connector and put

the battery back.

Step 1:

a. Remove the battery cover.

Step 2:

a. Loosen the battery strap.

b. Disconnect battery cable connector

to remove battery.

c. Replace with new battery and

re-connect the battery connector.

Step 3:

a. Tighten the battery strip and

close the battery cover.

Front Panel

OUTPUT

BATTERY

Note: please always mount the unit on the wall when it is working.

AC OUT PUT B AT TER Y

Back Panel

Color Condition

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and operation of this device.

Read this manual thoroughly before attempting to unpack , install or operate this device.

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is

disconnected.

CAUTION!

To reduce the risk of fire or electric shock, install in a temperature and humidity

controlled indoor area, free of conductive contaminants. To find the acceptable

temprature and humidity ranges,please refer to the device specifications.

CAUTION!

To reduce the risk of electric shock, keep the cover on. there are no user serviceable

parts inside the unit, including the battery. Please contact us or our dealer for service.

CAUTION! When replacing batteries, the replacement should have the same rating:

Listed/Certified Valve Regulated Lead Acid Battery, 12V, max. 20Ah.

CAUTION! Before replacing batteries, remove conductive jewelry, such as chains, watches and rings,

and use tools with insulated handles. High energy passed through conductive materials

can cause severe burns.

CAUTION! Don’t dispose of batteries in a fire. Batteries may explode if improperly disposed.

Recycle batteries in accordance with local regulations.

The UPS battery is charging when it’s connected to utility power. The battery is charging

during its first 24 hours of normal operation. Don’t expect full battery capacity during this

initial charging period.

CAUTION!

CAUTION! It is recommended to connect the unit to the required equipment and battery before

plugging in the utility power.

CAUTION! Runtimes based on testing fully-charged, new batteries at normal operating conditions.

Runtime curve is approximate and varies based on battery age, level of charge at test,

environment, and other variables.

CAUTION! To avoid electric shock, unplug power cable from the AC power source before servicing

the battery or installing a computer component.

The battery must be supplied by CyberPower. Using improper battery which is not

evaluated with this model could cause a risk and is at the user's own risk.

CAUTION!

Mounting Surface

1"~1.5"

1/8"

1/4"

17/32"

RECOMMENDED SCREW SIZE

SPECIFICATION

48V

48V RTN

SIG RTN

ON BATTERY

REPLACE BATTERY

BATTERY MISSING

LOW BATTERY

+ Voltage output

- Voltage output

Signal return

Low when operating from utility line.

Open when operating from battery.

Low when battery is charged.

Open when battery fails the Self Test.

Low when battery is present.

Open when battery is missing.

Low when battery is near full charge capacity.

Open when operating from a battery with < 20% capacity.

Signal Message

MODEL

Input Voltage Range

Input Frequency Range

Input Power Cord

AC Input

CBN50U48A-1

Standard NEMA1-15P

2-Prong Power Cord

90- 264VAC

50 - 60 Hz

(L*W*D)

On Battery Output Voltage

Continuous Power Capability

Output Power Max

E ficiency (at Full Load, 25°C )f

Battery Type

Numbers of Battery

Typical Recharge Time (25°C)

Replaceable

Lightning / Surge Protection

Audible Indicator

LED Indicators

Auto-Charge

Communication Interface

Maximum Dimensions

Weight

Operating Temperature

Operating Humidity

Max Operating Elevation

Max Storage Elevation

Storage Temperature

Environment

Battery

DC Output

Physical

Surge Protection and Filtering

Warning Diagnostics

Management

48VDC

50W

20AH / 12V x 1

30cm x 28cm x 10.1cm

7.9Kg

Sealed, Maintenance Free Lead-Acid Battery

On Battery, Replace Battery, Battery Missing, Low Battery

32°F - 104°F (0°C - 40°C)

10,000 ft (3,048m)

Utility Failure, Low Battery

50,000 ft (15,240m)

5°F - 113°F (-15°C - 45°C)

>85%

Around 38 hours (90% Charged)

Yes

AC, Output, Battery

Yes

0 - 95% noncondensing within enclosure

COMMUNICATION SIGNALS

Utility Power Cord Inlet

Communication signals

LIMITED WARRANTY

CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years from the date of original purchase, subject to the terms of this Limited

Warranty. This Limited Warranty gives you specific rights, and you may have other rights, which vary from State to State or Province to Province.

Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to three years. This provision shall NOT create any Implied Warranty or

Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product. NOTE: Some States and Provinces do not allow limitations on how long an implied warranty lasts,

so the above limitation may not apply to you.

To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty. Your sole and exclusive remedies are those provided by this

Limited Warranty. This exclusion of other express warranties applies to written and oral express warranties. CyberPower excludes any liability for personal injury. CyberPower excludes any liability for direct,

indirect, special, incidental, or consequential damages, whether for damage to or loss of property, loss of profits, business interruption, information or data. This exclusion applies even though damage or loss

is caused by negligence or other fault. NOTE: Some States or Provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation may not apply to you.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.

CyberPower does not sell the PRODUCT for use in high-risk activities. The PRODUCT is not designed or intended for use in hazardous environments requiring fail-safe performance, including the operation

of nuclear facilities, aircraft navigation or communication systems, air traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the PRODUCT

could lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life support device (collectively, "High Risk Activities").

CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities. CyberPower does not authorize use of any PRODUCT in any High Risk activities.

ANY SUCH USE IS IMPROPER AND IS A MISUSE OF A CYBERPOWER PRODUCT.

The Limited Warranty is governed by the laws of the United States and the State of Minnesota, without reference to conflict of law principles. The application of the United Nations Convention of Contracts for

the International Sale of Goods is expressly excluded

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an

experienced radio/TV technician for help.