CyberData Systems 011520 Bedienungsanleitung

CyberData Systems Lautsprecher 011520

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberData Systems 011520 (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 51 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Quick Start Guide 931741A

The IP Endpoint Co mpany

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. The ceiling tile is an adapter for the SIP-enabled IP Speaker. Download the

current manual, otherwise known as an Operations Guide, which is available

in the Downloads tab at the following webpage:

https://www.cyberdata.net/products/011520

Note You can also navigate to the Downloads tab by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or

port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

011520 SIP 2X2 Ceiling Tile

PRODUCTS

VOIP PRODUCTS

Downloads

SIP ENABLED

IP Paging

Drop-In Speaker

SIP 2 x 2 Ceiling Tile Drop-In Speaker

Quick Start Guide

Quick Start Guide 931741A

3.0 Power Test

3.1. Plug the ethernet cable into the RJ45 port on the back of the speaker

enclosure. Monitor the switch port (and PoE injector, if applicable) LED

activity for power and network link status. See the following figure:

3.2. The IP addressing mode is set to DHCP on default. If there is no DHCP

server available on the network, it will try 12 times with a three second delay

between tries and eventually fall back to the programmed static IP address

(by default 10.10.10.10). This process will take approximately 80 seconds.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Ethernet cable

Quick Start Guide 931741A

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• Computer

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a computer that is connected to the same switch

as a single CyberData device. Note the subnet of the test computer.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the following

link:

https://www.cyberdata.net/pages/discovery

4.3. Wait for initialization to complete before using the Discovery Utility program

to scan for a device. The device will show the current IP address, MAC

address, and serial number.

4.4. Select the device.

4.5. Click Launch Browser. If the IP address is in a reachable subnet from the

computer that you are using to access the device, the Discovery Utility

program should be able to launch a browser window pointing to the device’s

IP address.

4.6. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.7. Perform an audio test by pressing the Test Audio button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.8. The device is now ready to be set for your desired network configuration.

You may search the Compatible IP-PBX Servers index for available

sample VoIP phone system configurations and set up guides at the following

website address:

https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers

Produktspezifikationen

Marke:	CyberData Systems
Kategorie:	Lautsprecher
Modell:	011520
WLAN:	Nein
Bluetooth:	Nein
Breite:	605 mm
Tiefe:	77 mm
Gewicht:	5440 g
Empfohlene Nutzung:	Gegensprechanlage
Produktfarbe:	Grau
Übertragungstechnik:	Kabelgebunden
Höhe:	605 mm
Energiequelle:	PoE
RMS-Leistung:	- W
Betriebstemperatur:	-40 - 55 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Verpackungsbreite:	647.7 mm
Verpackungstiefe:	101.6 mm
Verpackungshöhe:	622.3 mm
Paketgewicht:	6350 g
Zertifizierung:	CE; EMC Directive - Class A EN 55032 & EN 55024, LV Safety Directive- EN 60950-1, RoHS Compliant, FCC; Part 15 Class A, Industry Canada; ICES-3 Class A
Menge pro Packung:	1 Stück(e)
Temperaturbereich bei Lagerung:	-40 - 70 °C
Audio Kanäle:	- Kanäle
Fernbedienung:	Ja
Nachhaltigkeitskonformität:	Ja
Nachhaltigkeitszertifikate:	CE, RoHS
Lautsprecherplatzierung:	Deckenmontage möglich