Crestron FT-TS600-B Bedienungsanleitung

Crestron Nicht kategorisiert FT-TS600-B

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Crestron FT-TS600-B (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

DO GUIDE

FT-TS600

FlipTop™ Touch Screen

DO Install the Device

Installing the Bushings

The Crestron® FT-TS600 ships with two cable management

plates preinstalled. These provide a pullout cable solution for

the AUD OUT (audio output), COMPUTER, and LAN cables. A

6 foot (1.8 meter) USB type A to type B cable is included for

the COMPUTER connection. Cables are looped through the

cable management plates.

The included bushings must be installed before mounting the

FT-TS600 into a surface. For a neat appearance, any unused

openings can be lled using the included hole plugs. The only

tool required to install the bushings is a Phillips screwdriver.

1. Remove the two cable management plates and retain the

two 06-32 x 1/4” screws.

2. Place the bushings on the cables (eight bushings

supplied).

3. Thread the cables through the appropriate slots in each

cable management plate.

4. Snap the bushings into the cable management plate

slots.

5. Feed all excess cable through the bushings.

6. Attach each cable management plate by sliding the

dovetail into the slot shown below, dropping the front

of the cable management plate into place, and then

securing the cable management plate with the

06-32 x 1/4” screw from step 1.

Mounting into a Surface

The FT-TS600 is designed

to mount into a horizontal

sur face, such as a desktop,

lectern, or podium. The

following diagram illustrates

the required cutout dimensions

to accommodate the

FT-TS600.

NOTE: Before inserting the FT-TS600 into the mounting hole,

ensure that all require cables have been installed.

The only tools required are a Phillips screwdriver and a #10

Allen wrench. To mount the FT-TS600, use the following

procedure:

1. Position the FT-TS600 in the mounting hole.

2. Install the four included 10-32 x 2” socket screws in the

metal mounting plates (two screws per plate).

3. Slide the moutning plates over the studs on each side of

the FT-TS600.

4. Turn the four 10-32 x 2” socket screws equally until they

contact the underside of the mounting surface.

NOTE: Do not overtighten the screws because this may

damage the surface or the unit.

DO Check the Box

QTY PRODUCT PART NUM.

2 Mounting Plates 2036985

4 Screws, 10-32 x 2", Socket 2037109

4 Small Hole Plugs 2036647

4 Large Hole Plugs 2036649

4 Small Bushings 2009522

4 Large Bushings 2010496

1 Connector, 3-Pin 2003575

1 Cable, USB 2.0, A-B, 6' (1.8 m) 2014966

1 Cutout Template 4519221

Cable Management Plates (2)

Bushing

Screws (2) 06-32 x 1/4”

The cable management

plate dovetail inserts here.

Maximum

Radius

1/8”

(4 mm)

6 1/4”

(159 mm)

7 1/2”

(190 mm)

Screws (4) #10-32 x 2”

Mounting Surface

Mounting Plates

Surface Cutout

Studs for the

Mounting Plate

DO GUIDE DOC. 7784A (2043774) 04.15

Specications subject t o change without notice.

DO Connect the Device

Make the necessary connections as called out in the illstration

that follows.

When making connections to the FT-TS600, note the

following:

• Use Crestron power supplies for Crestron equipment.

• The included cable cannot be extended.

CAUTION: Do not apply excessive pressure to the touch

screen display during handling. Doing so can crack the screen

and damage the device.

NOTE: Ensure the unit is properly grounded by connecting

the chassis ground lug to an eargh ground (building steel).

DO Access the Setup Screens

NOTE: The FT-TS600 can take up to 45 seconds to boot.

NOTE: If no project has been loaded or if an invalid project

has been loaded, the screen displays the following message:

“There is no display project to start. [Touch Screen to Enter

Setup...].”

The setup screens enable basic conguration prior to regular

operation of the FT-TS600.

During regular operation of the touch screen, there are two

ways to access the setup screens:

1. Place a button on the project main page and assign the

reserved join number (17242) that accesses the setup

screens.

2. Press hard keys 1, 2, 3, and 4 on the right side of the

touch screen display in sequence twice (press 1, 2, 3, 4,

1, 2, 3, 4) within a 5 second period.

DO Learn More

Visit the website for additional information

and the latest rmware updates.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories, Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Caution: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

Crest ron product development soft ware is licensed to Crest ron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Soft ware Development Tools

License Agreement. Crestron product operating system soft ware is licensed to Crest ron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of t hese Agreements

can be found on the Crest ron website at .www.crestron.com/legal/sof twar e_license_agreement

The specic patents that cover Crestron products are listed at . The product warranty can be found at .patents.crest ron.com www.crest ron.com/warranty

Crest ron and the Crestron logo are either trademarks or regist ered t rademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks

or regist ered trademarks of Underwriters Laboratories, Inc. in the United Stat es and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document

to refer to either the entities claiming the marks and names or their products. Crestron disclaims any propriet ary interest in t he marks and names of ot hers. Crestron is not responsible f or

errors in typography or photography.

This document was writ ten by the Technical Publicat ions depart ment at Crest ron.

Ground

LAN PoE:

10BASE-T / 100BASE-TX

Ethernet to LAN

COMPUTER:

To PC

AUD OUT:

To Balanced

Line Level Input

Produktspezifikationen

Marke:	Crestron
Kategorie:	Nicht kategorisiert
Modell:	FT-TS600-B
Display-Typ:	TFT
Bildschirmdiagonale:	5 "
Eingebaute Lautsprecher:	Nein
RAM-Kapazität:	1024 MB
WLAN:	Nein
Breite:	203 mm
Tiefe:	172 mm
Gewicht:	2400 g
Produktfarbe:	Schwarz
Höhe:	218 mm
Befestigungstyp:	In der Wand
Betriebstemperatur:	0 - 45 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Gehäusematerial:	Aluminium, Metal
Helligkeit:	300 cd/m²
Kontrastverhältnis:	450:1
Bildwinkel, horizontal:	69 °
Bildwinkel, vertikal:	64 °
Ethernet LAN Datentransferraten:	10, 100 Mbit/s
Speicherkapazität:	4000 MB
Seitenverhältnis:	15:9
Typ der Hintergrundbeleuchtung:	LED
Farbtiefe:	24 Bit
Touchscreen Technologie:	Projizierts Kapazitivsystem
Anzahl RJ-45-Anschlüsse:	1
Display-Auflösung:	800 x 480 Pixel
Ethernet/LAN:	Ja