Crestron DMPS3-4K-100-C Bedienungsanleitung

Crestron Nicht kategorisiert DMPS3-4K-100-C

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Crestron DMPS3-4K-100-C (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
DO GUIDE
DMPS3-4K-50 Rear Panel Connections
DMPS3-4K-100-C Rear Panel Connections
Information about VGA, DM OUT, AUDIO OUT, LAN, and NET pin assignments follows.
DMPS3-4K-50/DMPS3-4K-100-C
3-Series® 4K DigitalMedia™ Presentation Systems
DO Install the Device
The Crestron® DMPS3-4K-50 and DMPS3-4K-100-C can be mounted into a rack, mounted under a table, or placed onto a at surface.
Mount into a Rack
The DMPS3-4K-50 and DMPS3-4K-100-C each occupy 1U of rack space. Using a #1 or #2 Phillips screwdriver, attach the two included rack ears to the
device. Then, mount the device into the rack using four mounting screws (not included).
Mount under a Table
Using a #1 or #2 Phillips screwdriver, attach the four included table mount brackets to the device. Then, attach the four table mount brackets to the underside
of the table using four mounting screws (not included).
Place onto a Flat Surface
When placing the device onto a at surface or stacking it with other equipment, attach the included feet near the corners on the underside of the device.
DO Connect the Device
Make connections to the rear panel of the device. Refer to the following illustrations for information about DMPS3-4K-50 and DMPS3-4K-100-C connections.
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
2 Bracket, Rack Ear, 1U 2032122
4 Bracket, Under Table Mount 2041951
1 Connector, 4-Pin 2003576
2 Connector, 5-Pin 2003577
1 Emitter Probe, IR, Crestron® STIRP 2001137
4 Foot, 0.5" x 0.5" x 0.23", Rubber 2002389Black
1 Power Cord, 6' 7" (2 m) 2001134
DMPS3-4K-100-C Only
1 Connector, 3-Pin 2003575
Ground
MIC IN:
From
microphone
AUDIO OUT:
To balanced/
unbalanced
stereo line
level audio
output device
IR OUT:
To Crestron
STIRP IR
emitter probe
(included)
COM:
To
RS-232
device
USB 1–4:
To Crestron
TT-100 series
presentation
interfaces
NET:
To Cresnet
device
DM OUT:
To DM 8G+®
receiver or other
DM® device or to
HDBaseT® device*
LAN:
10BASE-T/100BASE-TX
Ethernet to LAN 100-240V~1.4A
50/60 Hz:
From ac
power outlet
VGA 1–4:
From RGB (VGA),
component, S-video, or
composite video sources
AUDIO 1–4:
From unbalanced
stereo line level
analog audio sources
HDMI 1–4:
From HDMI
audio/video
sources
HDMI OUT:
To HDMI
display
VGA 1–4:
From RGB (VGA),
component, S-video, or
composite video sources
AUDIO 1–4:
From unbalanced
stereo line level
analog audio sources
HDMI 1–4:
From HDMI®
audio/video
sources
HDMI OUT:
To HDMI
display
AUDIO OUT:
To balanced/
unbalanced
stereo line
level audio
output device
IR OUT:
To Crestron
STIRP IR
emitter probe
(included)
COM:
To
RS-232
device
Ground
LAN:
10BASE-T/100BASE-TX
Ethernet to LAN
USB 1–4:
To Crestron
TT-100 series
presentation
interfaces
NET:
To Cresnet®
device
100-240V~1.4A
50/60 Hz:
From ac
power outlet
DO GUIDE DOC. 7897C (2046349) 02.18
Specications subject t o change without not ice.
VGA Connector Pin Assignments
DM OUT Connector Wiring (DMPS3-4K-100-C Only)
AUDIO OUT Pin Assignments
LAN Pin Assignments
NET Pin Assignments
DO Determine the Address of the Device
The device can be addressed using the hostname. The default hostname is DMPS3-xxxxxxxx, where
xxxxxxxx consists of the last eight characters (excluding punctuation) of the MAC address. For example,
if the MAC address is 00:10:7F:08:09:AA:05, the default host name is DMPS3-0809AA05. The MAC
address is labeled on the shipping box and rear panel of the device.
Alternatively, the device can be addressed using the IP address. By default, DHCP is enabled. To set a
static IP address, use Crestron Toolbox™ software on a PC that connects to the device via the Ethernet
network or a USB connection to the COMPUTER port on the front panel of the device. If the PC connects
to the Ethernet network, the Device Discovery Tool within the Crestron Toolbox software can be used to
nd the current IP address.
DO Commission the System
Using the web interface, congure the device. To access the web interface, open a web browser and go
to the setup directory of the device by entering either of the following:
hostname hostname/setup ( is the hostname of the device)
or
xxx.xxx.xxx.xxx/setup (xxx.xxx.xxx.xxx is the IP address of the device)
The device also provides the built-in .AV Framework™ program, which enables complete system control
without requiring additional programming. To access the .AV Framework conguration interface, open a
web browser and go to either of the following:
hostname hostname:8008 ( is the hostname of the device appended by :8008)
or
xxx.xxx.xxx.xxx:8008 (xxx.xxx.xxx.xxx is the IP address of the device appended by :8008)
For more information, go to www.crestron.com/avframework.
DO Connect to the Crestron XiO Cloud Service
The Crestron XiO Cloud service allows supported Crestron devices across an enterprise to be managed
and congured from one central and secure location in the cloud. Supported devices are precongured
to connect to the service. Use of the service requires a registered Crestron XiO Cloud account.
To connect the device to the Crestron XiO Cloud service, do the following:
1. Record the MAC address and serial number that are labeled on the shipping box or rear panel
of the device. The MAC address and serial number are required in order to add the device to
the Crestron XiO Cloud environment.
2. Do either of the following:
• If you have a Crestron XiO Cloud account, go to https://portal.crestron.io to access the
Crestron XiO Cloud service.
• If you do not have a Crestron XiO Cloud account, go to www.crestron.com/xiocloud to
register for an account.
For detailed information about using the Crestron XiO Cloud service, refer to the Crestron XiO Cloud
Service User Guide (Doc. 8214) at www.crestron.com/manuals.
DO Allow Automatic Switching or Manually Select an Input
By default, automatic switching of inputs is enabled. Automatic switching causes the last connected
input to be routed to the output. The AUTO LED lights to indicate that automatic switching is enabled.
To manually select and activate the desired input, press one of the (1–4) or VGA HDMI (1–4) INPUT
SELECT buttons. Refer to the following table for a summary of the LED behavior of selected and
nonselected inputs.
NOTE: Manual selection of an input disables automatic switching. When automatic switching is
disabled, the AUTO LED turns off.
*The DM OUT port of the DMPS3-4K-100-C is a PoDM and HDBaseT PoE power sourcing equipment (PSE) port. Any wiring that
is connected to a PoDM or HDBaseT PoE PSE port is for intrabuilding use only and should not be connected to a line that runs
outside of the building in which the PSE is located.
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL
® Standards and requirements tested by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Rack Mounting Safety Precautions
• Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specied by the manufacturer.
• Reduced Airow: Installation of the equipment in a rack should be such that the amount of airow required for safe operation of the equipment is not compromised.
• Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
• Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration
of equipment nameplate ratings should be used when addressing this concern.
• Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).
Electrical Connection
“This product must be connected to an earthed mains socket-outlet.”
• Finland: “Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.”
• Norway: “Apparatet må tilkoples jordet stikkontakt.”
• Sweden: “Apparaten skall anslutas till jordat uttag.”
The specic patents t hat cover Crestron products are listed at . The product warrant y can be found at .www.crestron.com/legal/patents www.crestron.com/legal/sales-terms-conditions-warranties
Cert ain Crestron products contain open source sof t ware. For specic information, please visit . www.crestron.com/legal/open-source-sof tware
Crest ron, the Crestron logo, 3-Series, .AV Framework, Cresnet , Crest ron Toolbox, DigitalMedia, DM, DM 8G+, and VT Pro-E are either trademarks or registered t rademarks of Crestron Electronics, Inc., in the United States and/or other countries. Apple and iPad are eit her t rademarks or registered
trademarks of Apple Inc. in the United States and/or other count ries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United St ates and/or other countries. HDMI and the HDMI logo are either t rademarks or registered trademarks
of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are eit her trademarks or registered trademarks of Underwriters Laboratories, Inc. in the Unit ed States and/or other countries. Ot her trademarks, registered trademarks, and t rade names may be used in t his
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any propriet ary int erest in t he marks and names of ot hers. Crest ron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crest ron.
©2018 Crestron Electronics, Inc.
DO Learn More
Visit the website for additional information and the latestrmware
updates. To learn more about this product, use a QR reader application
on your mobile device to scan the QR images.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
DMPS3-4K-100-C
DMPS3-4K-50
PIN
NUM. RGB YPbPr S-VIDEO COMPOSITE
1 R CPr
2 G Y Y
3 B Pb COMP
5 GND GND GND GND
6 RED_GND C_GNDPr_GND
7 GRN_GND Y_GND Y_GND
8 BLU_GND Pb_GND
13 H
14 V
NOTE: For best video performance, ground connections should be
kept separate. Do not connect ground wires to the connector shell.
The connector shell is reserved for the cable shield.
PIN
NUM. WIRE COLOR PIN
NUM. WIRE COLOR
1 Orange/White 5 Blue/White
2 6Orange Green
3 7Green/White Brown/White
4 8Blue Brown
SIGNAL
NAME
BALANCED
AUDIO OUTPUT
UNBALANCED
AUDIO OUTPUT
+ L+ L+ Out
- L- Open
G Shield/Ground Common Ground
+ R+ R+ Out
- R- Open
PIN
NUM. SIGNAL PIN
NUM. SIGNAL
1 5TX+ N/C
2 6TX- RX-
3 7RX+ N/C
4 8N/C N/C
24: Power, 24 Vdc (Red Wire)
Y: Data (White Wire)
Z: Data (Blue Wire)
G: Ground (Black Wire)
Pin 1Pin 8
+ +
––
Pin 1
Pin 8
COLOR DESCRIPTION
Solid green The input is the active selection, and an incoming signal is detected.
Flashing green The input is the active selection, but an incoming signal is not detected.
Solid amber The input is not the active selection, but an incoming signal is detected.
Off The input is not the active selection, and an incoming signal is not detected.
Pin 10
Pin 5 Pin 1
Pin 6
Pin 15 Pin 11
5 1
1115
AMP
Left
Right
+ -G + -
Unbalanced Output
L R
+
+
Shield
AMP
Left
Right
+
-
G +
-
Balanced Output
L R
+
+

Produktspezifikationen

Marke: Crestron
Kategorie: Nicht kategorisiert
Modell: DMPS3-4K-100-C

Brauchst du Hilfe?

Wenn Sie Hilfe mit Crestron DMPS3-4K-100-C benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Crestron

Crestron

Crestron ZUMMESH-AVBRIDGE-I Bedienungsanleitung

6 September 2024
Crestron

Crestron HD-TX-4KZ-421-CHGR Bedienungsanleitung

6 September 2024
Crestron

Crestron HD-RX-4K-210-C-E Bedienungsanleitung

6 September 2024
Crestron

Crestron DM-NAX-16AIN Bedienungsanleitung

6 September 2024
Crestron

Crestron IV-CAMPTZ-12-N-SLVR-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IV-CAMFR-12-N-SLVR-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IVA-CPLT-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IV-CAMA3-20-SLVR-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IVA-CMT-BRKTJ-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IVA-WMT-SHELF-1B Bedienungsanleitung

6 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024