Crestron CSM-QMTDC-250-4-CN Bedienungsanleitung

Crestron Nicht kategorisiert CSM-QMTDC-250-4-CN

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Crestron CSM-QMTDC-250-4-CN (9 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/9
The CSM(I)-QMTDC-163 series, CSM(I)-QMTDC-250 series, and CSM
(I)-QMTDC-275 series Crestron® shade motors can be easily removed and
replaced. The CSM(I)-QMTDC series replacement motors are used to
replace an existing shade motor.
In
In
In
InIn t
t
t
tthe
he
he
hehe Box
Box
Box
BoxBox
1 CSM(I)-QMTDCSeries Motor, Replacement Motor
Mot
Mot
Mot
MotMotor
or
or
oror Rep
Rep
Rep
RepRepla
la
la
lalac
c
c
ccem
em
em
ememen
en
en
enent
t
t
tt
CA
CA
CA
CACAUTION:
UTION:
UTION:
UTION:UTION: Roll up the fabric to prevent damage while replacing the
motor.
N
N
N
NNOTES:
OTES:
OTES:
OTES:OTES:
lA soft and clean work surface is required to perform this
procedure.
lRemove the fascia and disconnect the motor cable before
performing this procedure.
R
R
R
RRe
e
e
eemove
move
move
movemove t
t
t
tth
h
h
hhe
e
e
ee R
R
R
RRoll
oll
oll
ollolle
e
e
eer
r
r
rr S
S
S
SSha
ha
ha
hahade
de
de
dede As
As
As
AsAsse
se
se
sesemb
mb
mb
mbmbl
l
l
lly
y
y
yy from
from
from
fromfrom t
t
t
tthe
he
he
hehe
M
M
M
MMount
ount
ount
ountounting
ing
ing
inging Br
Br
Br
BrBra
a
a
aac
c
c
ccke
ke
ke
kekets
ts
ts
tsts
1. Remove the old motor from the motor mounting bracket.
lFor a CSM(I)-QMTDC-163 series motor, press the release button
on the bottom of the shade motor.
lFor a CSM(I)-QMTDC-250 series or CSM(I)-QMTDC-275 series
motor, squeeze the two metal release clips next to the shade
motor.
2. Push the roller shade assembly towards the idler bracket to separate
the motor from the bracket. The idler pin compresses to allow the
motor end to swing out of the bracket.
3. Lift the idler end of the roller shade assembly and remove the idler pin
from the keyhole in the idler bracket.
4. Place the roller shade on a soft, clean surface where it will not be
damaged.
R
R
R
RRe
e
e
eemove
move
move
movemove t
t
t
tthe
he
he
hehe Old
Old
Old
OldOld M
M
M
MMot
ot
ot
ototor
or
or
oror from
from
from
fromfrom th
th
th
ththe
e
e
ee R
R
R
RRoll
oll
oll
ollolle
e
e
eer
r
r
rr Tube
Tube
Tube
TubeTube
CA
CA
CA
CACAUTION:
UTION:
UTION:
UTION:UTION: Do not remove the motor by pulling on the control wire.
Remove
Remove
Remove
RemoveRemove a
a
a
aa CSM(
CSM(
CSM(
CSM(CSM(I
I
I
II)
)
)
))-
-
-
--Q
Q
Q
QQMT
MT
MT
MTMTDC-1
DC-1
DC-1
DC-1DC-163
63
63
6363 o
o
o
oor
r
r
rr CSM(
CSM(
CSM(
CSM(CSM(I
I
I
II)
)
)
))-
-
-
--Q
Q
Q
QQMT
MT
MT
MTMTDC-2
DC-2
DC-2
DC-2DC-250
50
50
5050
Ser
Ser
Ser
SerSeries
ies
ies
iesies Mo
Mo
Mo
MoMotor
tor
tor
tortor
Pull the motor head to remove it from the tube.
N
N
N
NNOTES:
OTES:
OTES:
OTES:OTES: For CSM(I)-QMTDC-250 series motors:
lRemoving the motor may require a firm, hard pull.
lIf the motor is difficult to remove from the tube, reinstall the
motor latch and use it to help pull the motor from the tube.
1
1
1
11
C
C
C
CCSM
SM
SM
SMSM(I
(I
(I
(I(I)-Q
)-Q
)-Q
)-Q)-QMTDC
MTDC
MTDC
MTDCMTDC Seri
Seri
Seri
SeriSeries
es
es
eses Motor
Motor
Motor
MotorMotor Rep
Rep
Rep
RepRepla
la
la
lalac
c
c
ccem
em
em
ememe
e
e
eent
nt
nt
ntnt QuickStart
R
R
R
RRe
e
e
eep
p
p
ppl
l
l
lla
a
a
aac
c
c
cce
e
e
eemen
men
men
menment
t
t
tt M
M
M
MMot
ot
ot
ototor
or
or
oror
Remove
Remove
Remove
RemoveRemove a
a
a
aa CSM(
CSM(
CSM(
CSM(CSM(I
I
I
II)
)
)
))-Q
-Q
-Q
-Q-QMT
MT
MT
MTMTDC-2
DC-2
DC-2
DC-2DC-275
75
75
7575 Ser
Ser
Ser
SerSeries
ies
ies
iesies Mo
Mo
Mo
MoMotor
tor
tor
tortor
1. Remove the motor latch from the motor. Save the motor latch for
reassembly.
2. Roll the fabric around the hembar to expose the tube.
3. Reinstall the motor latch.
4. Remove the four screws from the tube.
5. Pull the motor head to remove it from the tube. If the motor is difficult
to remove from the tube, reinstall the motor latch and use it to help
pull the motor from the tube.
In
In
In
InInst
st
st
ststal
al
al
alall
l
l
ll t
t
t
tthe
he
he
hehe New
New
New
NewNew M
M
M
MMot
ot
ot
ototo
o
o
oor
r
r
rr i
i
i
iin
n
n
nn th
th
th
ththe
e
e
ee R
R
R
RRoll
oll
oll
ollolle
e
e
eer
r
r
rr T
T
T
TTub
ub
ub
ubube
e
e
ee
CSM(
CSM(
CSM(
CSM(CSM(I
I
I
II)
)
)
))-Q
-Q
-Q
-Q-QMT
MT
MT
MTMTDC-1
DC-1
DC-1
DC-1DC-16
6
6
663
3
3
33 S
S
S
SSer
er
er
ereries
ies
ies
iesies o
o
o
oor
r
r
rr CSM(
CSM(
CSM(
CSM(CSM(I
I
I
II)
)
)
))-Q
-Q
-Q
-Q-QMT
MT
MT
MTMTDC-2
DC-2
DC-2
DC-2DC-250
50
50
5050 Se
Se
Se
SeSeries
ries
ries
riesries
Mo
Mo
Mo
MoMot
t
t
tto
o
o
oors
rs
rs
rsrs:
:
:
::
1. Fully insert the new motor into the tube. The tube is designed so that
the motor can be easily inserted in only one orientation.
N
N
N
NNOT
OT
OT
OTOTES:
ES:
ES:
ES:ES:
lIf the motor does not easily slide into the tube, rotate the motor
180-degrees and then insert the motor into the tube.
lThe CSM(I)-QMTDC-250 series motors will snap in place. Gently
pull to ensure that the motor is properly secured in the motor
tube.
2. Install the shade assembly according to the mounting bracket’s
installation guide.
CSM(
CSM(
CSM(
CSM(CSM(I
I
I
II)
)
)
))-Q
-Q
-Q
-Q-QMT
MT
MT
MTMTDC-2
DC-2
DC-2
DC-2DC-275
75
75
7575 S
S
S
SSerie
erie
erie
erieeries
s
s
ss Mo
Mo
Mo
MoMotor
tor
tor
tortors:
s:
s:
s:s:
1. Insert the motor into the tube.
2. Ensure that a cusp on the motor crown aligns with the first screw hole
in the roller tube. The cusp should be no further than 1/4 in. (7 mm) off
center of the screw hole. Ensure that the motor head is flush with the
roller tube.
3. Rotate the motor head so that the groove in the motor is shown
through the second screw hole in the roller tube and then use a Phillips
tip screwdriver and two supplied screws to secure the motor head to
the tube. Do not overtighten.
4. Use a Phillips tip screwdriver and two supplied screws to secure the
motor crown to the tube. Do not overtighten.
2
2
2
22
C
C
C
CCSM(I
SM(I
SM(I
SM(ISM(I)
)
)
))-
-
-
--Q
Q
Q
QQMTDC
MTDC
MTDC
MTDCMTDC Seri
Seri
Seri
SeriSeries
es
es
eses Motor
Motor
Motor
MotorMotor Rep
Rep
Rep
RepRepla
la
la
lalac
c
c
ccem
em
em
emement
ent
ent
entent QuickStart
R
R
R
RRe
e
e
eepl
pl
pl
plpla
a
a
aaceme
ceme
ceme
cemecement
nt
nt
ntnt M
M
M
MMot
ot
ot
ototo
o
o
oor
r
r
rr
R
R
R
RRe
e
e
eei
i
i
iins
ns
ns
nsnst
t
t
tta
a
a
aall
ll
ll
llll t
t
t
tthe
he
he
hehe R
R
R
RRoll
oll
oll
ollolle
e
e
eer
r
r
rr Shad
Shad
Shad
ShadShade
e
e
ee As
As
As
AsAsse
se
se
sesembl
mbl
mbl
mblmbly
y
y
yy
After the motor has been fully installed, roll the fabric back onto the tube
(if applicable), and then install the shade assembly according to the
mounting bracket’s installation guide.
N
N
N
NNOTE:
OTE:
OTE:
OTE:OTE: Limits need to be set after installation. Refer to Motor
Programming for details.
Mot
Mot
Mot
MotMoto
o
o
oor
r
r
rr W
W
W
WWiri
iri
iri
iriiring
ng
ng
ngng
R
R
R
RRout
out
out
outouting
ing
ing
inging th
th
th
ththe
e
e
ee Cab
Cab
Cab
CabCabl
l
l
lles
es
es
eses
To ensure proper functionality and a clean look, consider the following
when routing cables and making connections:
lThe cables should exit the wall near the motor end of the shade
assembly.
lRoute the cables so that they remain out of sight.
lThe brackets provide a cutout in the upper corner, which allows wiring
to be easily run to the motor.
lA 2-pin connector may be required for shades with a large roll-up
diameter.
lUse cable ties to secure the cables to the loop on the bracket.
lEnsure that the cables and connectors do not make contact with the
shade fabric.
M
M
M
MMa
a
a
aaki
ki
ki
kiking
ng
ng
ngng th
th
th
ththe
e
e
ee Con
Con
Con
ConConne
ne
ne
nenec
c
c
cction
tion
tion
tiontions
s
s
ss
N
N
N
NNOTES:
OTES:
OTES:
OTES:OTES:
lWhen making the connections, do not use CRESNET-HP cable with
the small connector. When using CRESNET-HP cable, replace the
connector on the motor pigtail with the larger connector that is
supplied with the shade.
lAll shades should be home run from the power supply (sold
separately).
Cresnet
Cresnet
Cresnet
CresnetCresnet QM
QM
QM
QMQMT®
T®
T®
T®T® Sha
Sha
Sha
ShaShad
d
d
dde
e
e
ee Mot
Mot
Mot
MotMotor
or
or
oror wit
wit
wit
witwith
h
h
hh t
t
t
tthe
he
he
hehe Power
Power
Power
PowerPower an
an
an
anand
d
d
dd Con
Con
Con
ConControl
trol
trol
troltrol Com
Com
Com
ComComing
ing
ing
inging fro
fro
fro
frofrom
m
m
mm th
th
th
ththe
e
e
ee Sa
Sa
Sa
SaSam
m
m
mme
e
e
ee
Sou
Sou
Sou
SouSource
rce
rce
rcerce
Cresnet
Cresnet
Cresnet
CresnetCresnet QM
QM
QM
QMQMT
T
T
TT Sha
Sha
Sha
ShaShad
d
d
dde
e
e
ee Mo
Mo
Mo
MoMot
t
t
ttor
or
or
oror wit
wit
wit
witwith
h
h
hh th
th
th
ththe
e
e
ee Pow
Pow
Pow
PowPowe
e
e
eer
r
r
rr a
a
a
aand
nd
nd
ndnd Con
Con
Con
ConCont
t
t
ttrol
rol
rol
rolrol Com
Com
Com
ComComing
ing
ing
inging from
from
from
fromfrom Sep
Sep
Sep
SepSepara
ara
ara
araarate
te
te
tete
Sou
Sou
Sou
SouSources
rces
rces
rcesrces
3
3
3
33
C
C
C
CCSM(I
SM(I
SM(I
SM(ISM(I)-Q
)-Q
)-Q
)-Q)-QMTDC
MTDC
MTDC
MTDCMTDC Seri
Seri
Seri
SeriSeries
es
es
eses Motor
Motor
Motor
MotorMotor Rep
Rep
Rep
RepRepla
la
la
lalac
c
c
cce
e
e
eem
m
m
mment
ent
ent
entent QuickStart
R
R
R
RRe
e
e
eep
p
p
ppla
la
la
lalac
c
c
cce
e
e
eemen
men
men
menment
t
t
tt M
M
M
MMot
ot
ot
ototor
or
or
oror

Produktspezifikationen

Marke: Crestron
Kategorie: Nicht kategorisiert
Modell: CSM-QMTDC-250-4-CN

Brauchst du Hilfe?

Wenn Sie Hilfe mit Crestron CSM-QMTDC-250-4-CN benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Crestron

Crestron

Crestron ZUMMESH-AVBRIDGE-I Bedienungsanleitung

6 September 2024
Crestron

Crestron HD-TX-4KZ-421-CHGR Bedienungsanleitung

6 September 2024
Crestron

Crestron HD-RX-4K-210-C-E Bedienungsanleitung

6 September 2024
Crestron

Crestron DM-NAX-16AIN Bedienungsanleitung

6 September 2024
Crestron

Crestron IV-CAMPTZ-12-N-SLVR-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IV-CAMFR-12-N-SLVR-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IVA-CPLT-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IV-CAMA3-20-SLVR-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IVA-CMT-BRKTJ-1B Bedienungsanleitung

6 September 2024
Crestron

Crestron IVA-WMT-SHELF-1B Bedienungsanleitung

6 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024