Crestron CCS-UC-100 Bedienungsanleitung
Crestron
Videokonferenzsystem
CCS-UC-100
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Crestron CCS-UC-100 (4 Seiten) in der Kategorie Videokonferenzsystem. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
quickstart guide
CCS-UC-100
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
Crestron RL™ Group Collaboration System for Lync®
1
CCS-UC-100
For regulatory compliance information, refer to Doc. 7548.
1Preparation
2Installation
Typical CCS-UC-100 installation procedures are provided in
steps A through H. For detailed information about the
CCS-TS-6500 Tilting Wall Mount for 65” Display, refer to the
included CCS-TS-6500-WMK Installation Guide (Doc. 7511).
Alternate mounting procedures for the CCS-UC-CODEC-100
are provided in step I.
A. Verify Contents
Before starting installation, check the system package contents. Included items are listed in the
following table. Retain all documents and parts supplied for use in the installation process.
Crestron RL™ is a comprehensive group collaboration solution that combines Crestron® hardware with
Microsoft® Lync® software. The Crestron RL solution is based on Microsoft Lync 2013, a popular and
powerful server-based application that many companies already use on a daily basis. This full-featured,
unified communication system enables video, voice, interactive content sharing, presence, and chat from
one touch screen interface.
Two Crestron RL systems are offered. The dual display system (CCS-UC-100-2 KIT) is perfect for medium
to large conference rooms, and includes two high-definition 65" touch displays. The single display system
(CCS-UC-100-1 KIT) includes a single 65" touch display and is ideally suited for small to medium sized
conference rooms, executive offices, and huddle rooms.
.
C. Install Cable Tray
Attach the supplied cable tray to the rear of the codec
as follows:
1. Attach all interface and power cables to the rear
of the codec, including those that connect to the
CCS-TX-201-C and PoE injector mounted on the
accessory bracket assembly. (Refer to the
connection details on page 3.)
2. Route the cables right or left toward their
intended termination point, and bundle them with
plastic tie wraps as necessary.
3. Loosen the two screws indicated in the illustration
below approximately 1/4” (6 mm).
4. Mount the cable tray on the screws, slide the tray
to the right to engage the keyhole slots, and
tighten the screws.
Cable Tray
Mounting
Screws
B. Install Mounting Brackets on Codec
1. Remove three side cover bottom screws from each
side of the codec and discard them.
2.
Attach right and left codec mounting brackets to
codec using the supplied screws.
.
Screws
(3 Each Side)
Supplied
Codec Mounting
Bracket, Right
(Codec Mounting
Bracket, Left Not
Shown)
Side Cover Bottom
Screws
1. Mounting hardware included.
2. One in CCS-UC-100-1 KIT; two in CCS-UC-100-2 KIT
NOTE: Mounting hardware is packaged with the parts and
assemblies to be attached.
2. Use two plastic tie wraps (supplied), to attach the power
supply for the 65” touch screen overlay to the accessory
bracket in the area indicated by the dashed line in the
illustration above. The port for the ac power source should
face to the right.
3. Cut the tie wraps securing the power strip cable to the
accessory bracket (secured for shipping only).
.
Wall Plate Accessory
Bracket
Mounting
Screws
Attach Supplied
Long Screws
To Brackets
DESCRIPTION PART NUMBER QTY
Touch Screen, Color, 10” TS-1051-C-B-S 1
Camera, USB, Fixed, 2 Megapixel CCS-CAM-USB-F-100 1
CCS, Cable, Audio, 3.5 mm to (2X) RCA, 3’ (1 m) CBL-AUD-3MM-RCA-3 1
CCS, Cable, Audio, 3.5 mm to (2X) RCA, 12’ (4 m) CBL-AUD-3MM-RCA-12 1
Cable, VGA to DVI, 30’ (~10 m) CBL-VGA-DVI-30 1
Cable, HDMI to DVI, 30’ (~10 m) CBL-HD-DVI-30 1
Cable, HDMI to DVI, 3’ (1 m) CBL-HD-DVI-3 1
Cable, HDMI to DVI, 20’ (~6 m) CBL-HD-DVI-20 1
Cable, CAT6, 14’ (~4.3 m) CBL-CAT6-14 1
CCS, Cable, Sleeve, Expandable, Wrap, 1/2” x 33” CBL-SLEEVE-EXPAND-WRAP 2
(13 x 838 mm) L, Blk 1/2-33-B
Crestron Collab Sys, Unified Comm, Codec, MSLYNC CCS-UC-CODEC-100 11
Crestron Collab Sys, SPK, Sound Bar, Blk CCS-SPK-SB-100-B 1
Wall Mount Kit: CCS-TS-6500 CCS-TS-6500-WMK 1
1
Crestron Collab Sys, Touch Screen, 65” (1.65 m), 1080p, Blk CCS-TS-6500-B 1
2
3 Cable Assembly CBL-HD-ASSY 1
Accessory Bracket Assembly CCSA-BRKT-100 11
Codec Mounting Bracket, Right N/A 11
Codec Mounting Bracket, Left N/A 1
1
Sound Bar Bracket N/A 11
Camera Bracket N/A 11
Cable Tray N/A 11
Shelf Mount Bracket Included with codec 1
Rack Mount Bracket Included with codec 2
Power Pack For Ethernet PWE-480SU 1
1’ (~0.3 m) LAN Cable CBL-CAT6-1 1
A. Install Accessory Bracket Assembly
1. Use the supplied 1/4-20 x 1/2” mounting screws to attach
the accessory bracket assembly to the wall plate (part of
the CCS-TS-6500).
Attach Power Supply
(Codec
Mounting
Brackets Not
Shown)
B. Tools Required
Installation requires the use of a #1 or #2 Phillips screwdriver as well as a socket wrench
with 1/2” and 7/16” sockets.
QUICKSTART DOC. 7479B (2035756, Sheet 1 of 2) 08.13
(Continued on following page)
2
quickstart guide
CCS-UC-100
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
QUICKSTART DOC. 7479B (2035756, Sheet 1 of 2) 08.13
Crestron RL™ Group Collaboration System for Lync®
CCS-UC-100
2Installation (Continued) I. Alternate Codec Mounting
The following information applies only to installations in which the
codec is not to be attached to a wall plate.
Table/Shelf Mounting
.
.
Rack Mount
Bracket - One
Each Side
.
Remove Three Side Cover Screws
and Discard. Typical, Both Sides
Attach Bracket To
Unit Using Screws
Supplied
Rack Mounting
Rack Rail
Rack Mount
Screws (Not
Supplied)
.
Remove Both Side Cover Top
Screws And Discard Before
Attaching Bracket To Unit.
Typical, Both Sides
Locate unit position and mounting holes under the table/shelf using
the supplied mounting template.
Attach Bracket To
Unit Using Screws
Supplied
Screws To Mount
To Table/Shelf
(Not Supplied)
Shelf Mount
Bracket - One
Each Side
F. Attach Sound Bar to Display
1. Attach the sound bar bracket to the bottom (recommended) or top
of the display frame using the four supplied screws as shown in
the following illustrations.
2. Remove the two screws and mounting brackets from the rear of
the sound bar as supplied, and use the screws to attach the sound
bar to the sound bar bracket. (Retain the mounting brackets for
possible alternate sound bar mounting configuration.)
Bottom Mounting
Configuration
Six Camera
Mounting
Locations
D. Attach Codec to the Wall Plate
1. Hook the mounting brackets attached to the codec to the top bar
of the wall plate.
2. With the brackets resting against the bottom bar, tighten the
bracket screws so that they extend under the bottom bar to
secure the codec in position.
E. Attach Display to the Wall Plate
Attach the display to the wall plate as described in the
CCS-TS-6500-WMK Installation Guide (Doc. 7511).
WARNING: At least two qualified people should perform the
mounting procedure. Personal injury and property damage can
result from dropping or mishandling the flat panel.
For regulatory compliance information, refer to Doc. 7548.
!
!
!
!
!
NOTE: If the camera is to be mounted in the top center position,
the screws already holding the touch overlay control box need to be
removed since the camera bracket uses the same screws. The
camera is then mounted on top of the control box, with one screw
going through both plates into the overlay frame.
Wall Plate
(Accessory
Bracket Assembly
Not Shown)
Tighten Bracket Screws To
Prevent Codec From Being
Accidentally Dislodged
Hook Brackets
To Top Bar
Bottom
Bar
Bracket
Screws
Sound Bar
Screw
Sound Bar
Screw
H. Attach Camera to Display
1. Insert the camera into the camera bracket for top (recommended) or
bottom mounting, and secure the camera using the single supplied
screw.
2. Use the two supplied screws to attach the camera bracket with
camera to the monitor frame in one of the three available locations
opposite the sound bar location.
Top Mounting
Configuration
Bracket Screws
Sound Bar
Screw
Sound Bar
Screw
Top Mounting
Configuration
Camera Camera
Bracket
Camera
Bracket
Camera
Bottom Mounting
Configuration
Sound Bar
Bracket
Sound Bar
Bracket
G. Alternate Sound Bar Mounting
In certain configurations, it may be desireable to have the sound bar
mounted on a wall or on a horizontal surface rather than on the 65”
touch screen. In such cases, refer to the instructions in the Quickstart
Guide (Doc. 7560) supplied with the sound bar.
quickstart guide
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
CCS-UC-100
For regulatory compliance information, refer to Doc. 7548.
Crestron RL™ Group Collaboration System for Lync®
3
CCS-UC-100
CODE TAG NAME PURPOSE
A CBL-USB-A-B-31 USB HID from codec to CCS-TX-201-C
B CBL-CAT6-51 Codec control LAN to CCS-TX-201-C
C CBL-HD-31 Codec to CCS-TX-201-C
D CBL-CAT6-12 CCS-TX-201-C to PoE injector DATA IN
E CBL-USB-A-B-3 USB HID from codec to overlay 1
F CBL-VGA-DVI-30 Codec video in from VGA laptop
G CBL-HD-DVI-3 DVI from codec to HDMI on display 1
H CBL-HD-DVI-20 DVI from codec to HDMI on display 2
I CBL-AUD-3MM-RCA-3 Codec audio out to sound bar
J CBL-HD-DVI-30 Codec video in from HDMI laptop
K CBL-CAT-6-14 LAN to building network
L CBL-USB-A-B-10 USB HID from codec to overlay 2
3Hookup (Typical)
Corporate
Network
LAN
PoE Injector
DM IN
TS-1051-C-B-S
DM OUT
Control
LAN
HDMI IN
USB
HID
Touch
Input
Bottom Panel
DM 8G+
(Copper)
Display
2
Display
1
HDMI IN
HDMI IN
Ground
(Connect to
Building Steel)
Audio to Sound Bar
Top Panel
HDMI From
Laptop
USB
Camera
VGA
From
Laptop
Room Laptop
Sound Bar
D
B
F
H
I
J
C
HDMI OUT
CCS-TX-201-C
Supplied Cables
Overlay 1
USB Monitor
Overlay Interface
1
USB
Mic
(Optional)
A
Overlay 2
1. Part of 3 cable assembly (Supplied already sleeved.)
2. Part of accessory bracket assembly
USB
HID
IN
USB
HID
IN
E
L
K
OR
24 Vdc
5 Vdc
5 Vdc
100-240 V - 1.25 A
50/60 Hz
Input Power
Not
Used
H
B
100-240 V - 1.25 A
50/60 Hz
Input Power
Part of Accessory Bracket Assembly
a
US
B
Mi
c
B
To USB Mouse and
Keyboard (For Setup Only)
DATA &
POWER
OUT DATA
IN
E
G
L
NOTE: Use the two supplied pieces of CCS-CBL-SLEEVE-EXPAND-WRAP
to enclose cables as follows:
• The power cable from the USB camera, the power supply cable for the
display 1 overlay, and the USB HID from the codec to overlay 1 (E).
• The power cable from power strip to the sound bar, the CBL-HD-DVI-3
cable (G) between the codec and display 1, and the power cable from the
power strip to the codec.
G
Not Used
Not Used
100-240 V - 1.25 A
50/60 Hz
Input Power
100-240 V - 1.25 A
50/60 Hz
Input Power
100-240 V - 1.25 A
50/60 Hz
Input Power
100-240 V - 1.25 A
50/60 Hz
Input Power
QUICKSTART DOC. 7479B (2035756, Sheet 2 of 2) 08.13
Produktspezifikationen
| Marke: | Crestron |
| Kategorie: | Videokonferenzsystem |
| Modell: | CCS-UC-100 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Crestron CCS-UC-100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Videokonferenzsystem Crestron
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
20 August 2024
20 August 2024
20 August 2024
20 August 2024
Bedienungsanleitung Videokonferenzsystem
- Videokonferenzsystem Da-Lite
- Videokonferenzsystem Asus
- Videokonferenzsystem HP
- Videokonferenzsystem Logitech
- Videokonferenzsystem Philips
- Videokonferenzsystem Sony
- Videokonferenzsystem Panasonic
- Videokonferenzsystem Yamaha
- Videokonferenzsystem Yealink
- Videokonferenzsystem Bose
- Videokonferenzsystem Jabra
- Videokonferenzsystem Sennheiser
- Videokonferenzsystem Tork
- Videokonferenzsystem Plantronics
- Videokonferenzsystem TOA
- Videokonferenzsystem Marshall Electronics
- Videokonferenzsystem AVerMedia
- Videokonferenzsystem Vtech
- Videokonferenzsystem Black Box
- Videokonferenzsystem InFocus
- Videokonferenzsystem Marantz
- Videokonferenzsystem Monoprice
- Videokonferenzsystem Iiyama
- Videokonferenzsystem Konftel
- Videokonferenzsystem Polycom
- Videokonferenzsystem Totolink
- Videokonferenzsystem Celexon
- Videokonferenzsystem IPEVO
- Videokonferenzsystem Lumens
- Videokonferenzsystem B-Tech
- Videokonferenzsystem DataVideo
- Videokonferenzsystem JPL
- Videokonferenzsystem Cisco
- Videokonferenzsystem Grandstream
- Videokonferenzsystem Kramer
- Videokonferenzsystem Vaddio
- Videokonferenzsystem Newline
- Videokonferenzsystem Anchor Audio
- Videokonferenzsystem AT&T
- Videokonferenzsystem Legamaster
- Videokonferenzsystem AMX
- Videokonferenzsystem Chief
- Videokonferenzsystem AVer
- Videokonferenzsystem ClearOne
- Videokonferenzsystem Gefen
- Videokonferenzsystem Aluratek
- Videokonferenzsystem Legrand
- Videokonferenzsystem PanaCast
- Videokonferenzsystem BZBGear
- Videokonferenzsystem Extron
- Videokonferenzsystem Atlona
- Videokonferenzsystem WyreStorm
- Videokonferenzsystem Alfatron
- Videokonferenzsystem LifeSize
- Videokonferenzsystem MuxLab
- Videokonferenzsystem VFI
- Videokonferenzsystem VDO360
- Videokonferenzsystem Owl Labs
- Videokonferenzsystem Huddly
- Videokonferenzsystem Angekis
- Videokonferenzsystem PulseAudio
- Videokonferenzsystem HuddleCamHD
- Videokonferenzsystem Heckler
Neueste Bedienungsanleitung für -Kategorien-
27 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
14 September 2024
12 September 2024
10 September 2024