Craftsman CMHT77633 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Craftsman CMHT77633 (10 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/10
Stud Sensor
Sensor De Parales
Capteur De Poteaux
Sensor de vigas
77-075
2
EN
USER MANUAL
CRAFTSMANÂź STUD SENSOR
The stud sensor uses electronic signals to locate the edges of studs or joists through
drywall and plywood up to 3/4”. Once the edge of a stud has been detected, the stud
sensor displays a red LED and sounds an audible tone. A pencil notch allows you to
easily note the stud edge on the wall.
WARNING
Protect Your Eyes. Wear Safety Goggles
OPERATING INSTRUCTIONS
BATTERY:
Open door on back of unit and connect a 9-volt battery to clip. Put battery back into
case and close back battery door.
USAGE:
Fig. 1 - Hold the stud sensor ïŹ‚at against the surface, making
ïŹrm contact.
‱ Press in and hold the activation button. The green and red
LED’s will light. When the red LED goes off, the unit is calibrated.
Keep holding the activation button during all of the following
procedures.
Note: While calibrating, the stud sensor must not be placed
directly over a stud, dense material such as metal, or over a wet
or newly painted area, or it will not properly calibrate. If the Red
LED stays lit, move to a different location and try again.
Fig. 2 - Slide the stud sensor slowly across the surface in a
straight line. As it detects a stud edge, the red LED will go on and
an audible tone will be heard.
‱ Use the handy pencil notch located at the top of the unit to
mark the stud edge.
Fig. 3-4 - Repeat the above steps from the other side of the stud.
Coming from the opposite direction, mark the other edge of the
stud. The midpoint of the two marks indicates the stud center.
CAUTIONS ON OPERATING
The proximity of electrical wiring or pipes to the surface of the
wall may cause the stud sensor to detect them as studs. You
should always use caution when nailing, cutting or drilling in
walls, ceilings and ïŹ‚oors that may contain these items. Always
remember that studs or joists are normally spaced 16 inches or
24 inches apart and are 1-1/2 inches in width. To avoid surprises
be aware that anything closer together or of a different width may
not be a stud.
Power LED
Activation
Button
Marking Notch
Edge
Detection LED
Fig. 1
Fig. 2
Fig. 3
Fig. 4
3
OPERATING TIPS
PREVENT INTERFERENCE
To ensure best performance from the stud sensor, keep your free hand at least 6
inches away from the unit and wall surface while testing or scanning surfaces.
CONVENTIONAL CONSTRUCTION
Doors and windows are commonly constructed with additional studs and headers
for added stability. The stud sensor detects the edge of these double studs and solid
headers as a single, wide stud.
SURFACE DIFFERENCES
Wallpaper – There will be no difference in the function of the stud sensor on surfaces
covered with wallpaper or fabric unless the coverings used contain metallic foil or
ïŹbers.
Ceilings – When dealing with a rough surface such as a sprayed ceiling, utilize a
piece of cardboard when scanning the surface. Run through the calibration technique
described earlier with the piece of cardboard too, to assure best performance of the
unit. Also, it is particularly important in this application to remember to keep your
free hand away from the unit.
SPECIFICATIONS:
(At 35-55% relative humidity)
Depth Range-Accuracy- Scanning and
marking the stud from two sides
Up to Ÿ” (19 mm)
through drywall
Stud center ±1/8” (3 mm) for wood
±1/4” (6 mm) for metal
Shock Resistance: Up to 3 feet (1 m) dropped onto concrete
Water Resistance: Water resistant,but not waterproof
Operating Temperature: +20°F to +120°F (-7°C to +49°C)
Storage Temperature: -20°F to +150°F (-29°C to +66°C)
LIMITED WARRANTY
Duration of coverage may vary; check product instructions for precise length of
coverage.
WARRANTY SERVICE
To obtain the warranty coverage stated below, return a defective product with proof of
sale to the retailer from which it was purchased.
CRAFTSMAN LIMITED WARRANTY
FOR ONE YEARfrom the date of sale, this product is warranted against defects in
material or workmanship.
WITH PROOF OF SALE, a defective product will be replaced free of charge.
This warranty does not cover expendable parts that can wear out from normal use
within the warranty period.
This warranty applies for only 90 days from the date of sale if this product is ever
used while providing commercial services or if rented to another person.
MADE IN CHINAMADE IN CHINA
CMHT77633CMHT77633
www.CRAFTSMAN.com
888-331-4569
www.CRAFTSMAN.com
888-331-4569


Produktspezifikationen

Marke: Craftsman
Kategorie: Nicht kategorisiert
Modell: CMHT77633

Brauchst du Hilfe?

Wenn Sie Hilfe mit Craftsman CMHT77633 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Craftsman

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-