Craftsman 48112 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Craftsman 48112 (9 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/9
Operator’s Manual
Model 48112
WARNING: Before using this product,
read this Operator’s Manual and follow
all its Safety Rules and Operating
Instructions.
• Safety
• Operation
• Maintenance
Printed in China
2 Ton Low Prole
Floor Jack
Sears Brands Management Corporation, Ho󰀨man Estates, IL 60179 U.S.A.
www.craftsman.com
ASME PASE Compliant
CUSTOMER HELP LINE
Parts and Questions
1-888-332-6419
8:00 AM - 4:45 PM Central Time
Monday- Friday
2
NOTE: Repeat this Air Purge Procedure
whenever the jack displays reduced lifting
performance.
AIR PURGE PROCEDURE
IMPORTANT: BEFORE FIRST USE, perform the following Air Purge Procedure to remove any air that may
have been introduced into the hydraulic system as a result of product shipment and handling.
REMOVE COVER PLATE
Loosen and remove the four screws
securing cover plate to jack frame.
Remove cover plate to expose oil îš¿ll plug.
CLOSE RELEASE VALVE
Remove handle from handle socket. Place
handle back onto release valve. Fully close
release valve by turning handle clockwise
until it stops.
READY FOR USE
Remove handle from release valve. Insert
handle into handle socket. Jack is now
ready to use. Check for proper pump action.
OPEN RELEASE VALVE
Place the open end of the handle over the
release valve so that the narrow crosspiece
in the handle tip engages into the slot in the
valve. Turn the handle counterclockwise 2
full turns to fully open release valve.
RAPIDLY PUMP
Remove handle from release valve. Insert
handle into handle socket. Turn handle
slightly to right to engage pin in slot. Rapidly
pump the handle 6 - 8 times. Leave handle
in down position.
PURGE AIR
With a at blade screwdriver, push the oil ll
plug slightly to the side to purge trapped air
from system. You should hear a hiss.
REPLACE COVER PLATE
Secure cover plate back in place with the
four previously removed screws.
1
2
3
4
5
7
6
CUSTOMER HELP LINE
Parts and Questions
1-888-332-6419
8:00 AM - 4:45 PM Central Time
Monday- Friday
Oil Fill Plug
(Not shown, on
reservoir)
Engage
release valve
with this end
Cover plate
(Remove to access
Oil Fill Plug)
Handle
socket
Lifting
arm
Saddle
Front
wheel
Release
valve
Jack
handle
Caster
3
Craftsman model 48112 features a 5,000 lbs.
maximum capacity. Lifting range for this jack
is 3-3/8 inches to 14-7/8 inches. Jack features
an overload valve bypass system to prevent
jack damage and user injury.
Speciîš¿cations
Compact design allows use in conîš¿ned spaces
Maximum load capacity.....2½ tons (5,000 lbs.)
Lift range........................3-3/8 to 14-7/8 inches
Weight ...................................................31 lbs.
WARNING: This product contains chemicals
known to the state of California to cause
cancer and birth defects or other reproductive
harm. www.P65Warnings.ca.gov
SAFETY INSTRUCTIONS
THIS IS A LIFTING DEVICE ONLY!
CRAFTSMAN LIMITED WARRANTY
DESCRIPTION
Read Operating Instructions
Study, understand and follow all instructions
in this manual before operating the jack.
Failure to heed these warnings may result in
loss of load, damage to the jack and/or jack
failure resulting in personal injury or property
damage.
Position the Jack
This jack is designed only for lifting part of
the total vehicle. Position the jack to only lift
on the areas of the vehicle speciîš¿ed by the
vehicle manufacturer.
Use Support Stands
After lifting the vehicle always support the
load with appropriately rated vehicle support
stands before working on the vehicle.
Do Not Overload Jack
Do not overload this jack beyond its rated
capacity. Overloading this jack beyond its
rated capacity can cause damage to or failure
of the jack.
Use on Hard Level Surface
This jack is designed only for use on hard
level surfaces capable of sustaining the load.
Use on other than hard level surfaces can
result in jack instability and possible loss of
load.
Center Load on Jack Saddle
Center load on jack saddle before lifting
vehicle. O󰀨-center loads and loads lifted
when the jack is not level can cause loss
of load or damage to the jack. Only use on
vehicles whose lift points îš¿t well with saddle
of this jack.
Do Not Use Jack as Dolly
Do not move or dolly the vehicle while it is on
the jack. Do not use this jack to lift or move a
building, mobile home or travel trailer of any
type.
KEEP HANDS AND FEET CLEAR OF THE
JACK HINGE MECHANISM AND GROUND
CONTACT AREA WHEN LOWERING THE
LOAD!
DO NOT work on vehicle supported by jack.
Immediately after lifting, support load with
appropriately rated vehicle support stands before
working on vehicle.
CRAFTSMAN LIMITED WARRANTY
FOR ONE YEAR from the date of sale this
product is warranty against defects in material
or workmanship. WITH PROOF OF SALE
a defective product will be replaced free of
charge.
For warranty coverage details to obtain
free replacement, visit the web page: www.
craftsman.com/warranty
This warranty applies for only 90 days from
the date of sale if this product is ever used
while providing commercial services or if
rented to another person.
This warranty gives you speciîš¿c legal rights,
and you may also have other rights which vary
from state to state.
Sears Brands Management Corporation,
Ho󰀨man Estates, IL 60179


Produktspezifikationen

Marke: Craftsman
Kategorie: Nicht kategorisiert
Modell: 48112

Brauchst du Hilfe?

Wenn Sie Hilfe mit Craftsman 48112 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Craftsman

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-