Conceptronic DDE02B Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Conceptronic DDE02B (15 Seiten) in der Kategorie Ladestation/Dockingstation. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/15
Multi Language Quick Guide
Dual Bay Hard Drive Docking
Station USB 3.0
DDE02B
V1.0
English
Conceptronic DDE02B
Installation & usage
Connect the hard disk docking station to your computer
Turn on your computer.
Connect the included power adapter to the DC connector at the backside of the
hard disk docking station and to a free wall outlet.
Connect the included USB 3.0 cable to the USB connector at the backside of
the hard disk docking station and to a free USB 3.0 port on your computer.
Note: You can also connect the hard disk docking station to a USB 2.0 or USB
1.1 port, but the speed will be limited to the speed of the USB controller of your
computer.
Insert a SATA hard disk in the hard disk docking station.
Turn on the hard disk docking station with the power switch at the backside.
The computer will automatically recognize and install the hard disk docking
station. No driver installation is required.
Safe remove the hard disk docking station from your computer
The hard disk docking station must be removed safely in your operating system
before you turn it off and remove the hard disk, in order to prevent data loss.
Double click the on Safely Remove Hardware” icon your system tray. in
The Safely Remove Hardware window will shown. be
Click on the connected hard disk docking station (often listed as “USB Mass
Storage Device”) and click the “Stop” button.
Confirm the disconnection by clicking OK”.
The hard disk docking station is now safely removed from your computer. You can
now turn off the hard disk docking station and remove the hard disk.
Duplicator (CLONE) Mode
The Duplicator Mode only works when the docking station is NOT connected to a PC
via the USB cable.
HDD A (Source): disk with the data you want to duplicate (clone).
HDD B (Destination): in which you want to store the data of the source disk.
Note: The capacity of the destination disk should be equal or larger than the source
disk. Make sure that those hard disks have no bad sectors. Bad sectors will cause
unpredictable problems.
Put the source disk into the , then, put the destination disk into the HDD A bay HDD
B bay. Please make sure that those hard drives are correctly and firmly connected
to those SATA connectors of the docking station.
Connect the power adapter to the docking station and power outlet.
Press the power button to power up the docking station.
Wait at least 10 seconds till the docking station is prepared.
Note: If you have important data on the hard disk, please back up the data before
beginning the Clone operation.
Keep pressing the Clone button for 3 seconds to begin duplication.
During the Clone process, those LED indicators will flash to show the percentage of
the progress:
Begin Clone process: 4 LEDs flash one by one.
Green LED stays solid: 25%
Red LED stays solid: 50%
Yellow LED stays solid: 75%
Orange LED stays solid: 100%
When the green, red, yellow & orange LEDs all stay solid, the process of the Clone
had been finished.
Note: Those hard drives may become hot during the Clone process.


Produktspezifikationen

Marke: Conceptronic
Kategorie: Ladestation/Dockingstation
Modell: DDE02B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Conceptronic DDE02B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Ladestation/Dockingstation Conceptronic

Bedienungsanleitung Ladestation/Dockingstation

Neueste Bedienungsanleitung für -Kategorien-