Citronic PPX600 Bedienungsanleitung
Citronic
Verstärker
PPX600
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Citronic PPX600 (4 Seiten) in der Kategorie Verstärker. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
PPX SERIES
POWER AMPLIFIERS
Order ref: 172.203UK, 172.206UK, 172.209UK
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
PPX Series User Manual
Introduction
Thank you for choosing a Citronic PPX series power amplifier as part of your sound reinforcement system. This high
output amplifier is designed to offer high quality, dependable service for mobile and installed systems. Please read this
manual fully and follow the instructions to achieve the best results with your new purchase and to avoid damage through
misuse.
Warning
To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.
If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel
before further use. Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –
Safety
• Check for correct mains voltage and condition of IEC lead before connecting to power outlet
• Ensure speaker leads are good condition with no short connections or damaged plugs
• Check impedance of speaker loads do not exceed the minimum stated load for the amplifier
• Do not allow any foreign objects to enter the case or through the ventilation grilles
Placement
• Keep out of direct sunlight and away from heat sources
• Keep away from damp or dusty environments
• When rack-mounting, ensure adequate support for the base of the amplifier and firm fixings for the front
• Ensure adequate air-flow and do not cover cooling vents at the front and rear of the amplifier
• Ensure adequate access to controls and connections
Cleaning
• Use a soft cloth with a neutral detergent to clean the casing as required
• Use a vacuum cleaner to clear ventilation grilles of any dust or debris build- ups
• Do not use strong solvents for cleaning the unit
Front Panel
1. Power switch and LED
2. CH1 level control
3. Protect LED indicators
4. Signal LED indicators
5. Clip LED indicators
6. CH2 level control
7. Cooling vent
PPX Series User Manual
Rear Panel
8. Cooling fan vent
9. CH1 & CH2 XLR input s
10. CH1 & CH2 jack inputs
11. GROUND LIFT switch
12. MODE switch
13. LIMITER switch
14. CH1 & CH2 binding post speaker outputs
15. CH1 & CH2 SPK connector outputs
16. IEC mains inlet and fuse
Operation
Connect speaker cabinets to channel outputs using good quality leads via the SPK connector or binding posts and ensure
that the combined load on each channel is no lower than 4 (for speaker loads connected in parallel, 8 8 4 ) Ω. Ω + Ω = Ω
Both channels can be used to drive a single load at the combined volume of each by switching to BRIDGE mode. In this
mode, the input is on channel 1 and output from CH1 SPK connecter (pins 1+ and 2-) or across the red terminals as “+”
indicated on the rear panel - WARNING - Minimum load for bridge mode is 8Ω
Connect each signal input from mixer or other line level source via the XLR or jack connectors on the rear panel using
good quality signal ads. le
For protection in high power situations, the onboard LIMITER may be switched in to protect from overload.
In situations with excessive mains coming through the speakers, it may help to switch the GROUND to the LIFT hum
position. This is may help in some situations but otherwise, it is preferred to be switched to GND.
Jack and XLR inputs for each channel are wired in parallel, allowing the signal to be carried forward to further amplifiers
if necessary (if the input is XLR, the jack may be used as a signal output and vice versa)
Connect the amplifier to a mains outlet, ensuring that the IEC lead is earthed, in good condition and connected securely.
With channel gain controls turned fully down, switch on the power to the amplifier. This unit -has a “soft start” function
which makes some checks before engaging power to the amplifiers, which may take a few seconds.
With mixer (or other signal source) levels turned down, gradually increase the amplifier’s channel level controls to the
required level (normally full) and then gradually increase the signal level from the mixer or sound source until sound can
be heard through the speakers and then continue increasing up to the required level.
During use, green “SIGNAL” LEDs will illuminate to show when a sign “CLIP” LEDs illuminate if the al is present and yellow
output is reaching clip level. If the red CLIP LEDs illuminate more than very briefly, reduce the volume until they hardly
light up at all.
If the internal protection circuitry detects a fault in the speakers or amp, the channel(s) will enter Protect Mode and red
“PROTECT” LEDs will illuminate on the front panel to show this. Switch the amplifier off and check the entire system
(including leads) before powering up again. If still in Protect Mode, seek advice from qualified service personnel.
Before powering down, turn the channel gain controls fully down to avoid loud noises when switching off.
Produktspezifikationen
| Marke: | Citronic |
| Kategorie: | Verstärker |
| Modell: | PPX600 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Citronic PPX600 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Verstärker Citronic
13 Juli 2024
Bedienungsanleitung Verstärker
- Verstärker Nedis
- Verstärker Sony
- Verstärker Yamaha
- Verstärker Alecto
- Verstärker MarQuant
- Verstärker Kenwood
- Verstärker Pyle
- Verstärker Auna
- Verstärker Beyerdynamic
- Verstärker Denon
- Verstärker Pioneer
- Verstärker Geemarc
- Verstärker JBL
- Verstärker Onkyo
- Verstärker Technics
- Verstärker Hifonics
- Verstärker Novero
- Verstärker Fenton
- Verstärker Rotel
- Verstärker Harman Kardon
- Verstärker Marshall
- Verstärker Naim
- Verstärker Power Dynamics
- Verstärker Samson
- Verstärker Skytec
- Verstärker Tangent
- Verstärker Vonyx
- Verstärker NAD
- Verstärker Fender
- Verstärker Behringer
- Verstärker Marantz
- Verstärker Arcam
- Verstärker Crown
- Verstärker Ecler
- Verstärker Luxman
- Verstärker Monacor
- Verstärker Sansui
- Verstärker TEAC
- Verstärker Thorens
- Verstärker Classé
- Verstärker Sherwood
- Verstärker Humantechnik
- Verstärker Bluetech
- Verstärker Skytronic
- Verstärker Reloop
- Verstärker Eden
- Verstärker American Audio
- Verstärker Anthem
- Verstärker HQ Power
- Verstärker Ibiza Sound
- Verstärker McIntosh
- Verstärker Hartke
- Verstärker DAP Audio
- Verstärker Elektra
- Verstärker Engl
- Verstärker Iriver
- Verstärker Koda
- Verstärker Konig Electronic
- Verstärker MaxGear
- Verstärker Meridian
- Verstärker Peavy
- Verstärker Quadral
- Verstärker Randall
- Verstärker Stagg
- Verstärker UPC
- Verstärker Velodyne
- Verstärker IFi Audio
- Verstärker Amplicom
- Verstärker Ampeg
- Verstärker Advance Acoustic
- Verstärker Mark Levinson
- Verstärker AB International
- Verstärker Alto Professional
- Verstärker Audica
- Verstärker Bellman
Neueste Bedienungsanleitung fĂĽr -Kategorien-
15 Oktober 2024
15 Oktober 2024
12 Oktober 2024
9 Oktober 2024
22 September 2024
19 September 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024