Cisco VWIC3-4MFT-T1/E1 Bedienungsanleitung

Cisco Netzwerkkarte / Adapter VWIC3-4MFT-T1/E1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Cisco VWIC3-4MFT-T1/E1 (9 Seiten) in der Kategorie Netzwerkkarte / Adapter. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/9

Data Sheet

Cisco Third-Generation 1-, 2-, and 4-Port T1/E1 Multiﬂex Trunk

Voice/WAN Interface Cards

These flexible interface cards support multiple integrated data, voice and video applications, facilitating the

migration from data only as well as circuit-switched voice/video services to a packet voice/video solution

Introduction

The Cisco® Third-generation 1-, 2-port and 4-port T1/E1 Multiﬂex Trunk Voice/WAN Interface (MFT VWIC3s) support

data and voice applications on the Cisco 1921, 1941 and 1941W (data only), and the Cisco 2901, 2911, 2921, 2951,

3925, 3945, 3925E and 3945E Integrated Services Routers. The Cisco MFT VWIC3 combines WAN-interface-card

(WIC) and voice-interface-card (VIC) functions to provide unparalleled ﬂexibility, versatility, and investment

protection through its many uses. Customers who choose to integrate data and voice in multiple steps preserve their

investment in a T1/E1 WAN interface because the Cisco MFT VWIC3 cards can be reused in packet voice

applications. The 2 port T1/E1 MFT VWIC3 is shown below.

Figure 1. Cisco 1-,2- and 4-Port T1/E1 MFT VWIC3

The Cisco MFT VWIC3 interface cards add improvements over the Cisco Second-generation 1- and 2-port T1/E1

Multiﬂex Voice/WAN Interface Cards (MFT VWIC2s). The Cisco 2- and 4-port MFT VWIC3s enable each port to be

clocked from an independent clock source for data applications. Voice applications can now be clocked

independently from data applications, with all ports for voice applications clocked from a single source. The Cisco

MFT VWIC3s use the ECAN on the motherboard PVDM cards with up to 128ms echo-tail length for demanding

network conditions. MFT VWIC3 cards support up to 2 channel groups per T1/E1 port for serial data applications.

Refer to Table 3 for all conﬁguration options oﬀered with the MFT VWIC3 cards.

The Cisco MFT VWIC3 cards can be inserted into the EHWIC slot on the supported Cisco 1921, 1941, 1941W,

2901, 2911, 2921, 2951, 3925, 3945, 3925E and 3945E integrated services routers. The T1/E1 MFT VWIC3 cards

support both T1 and E1, providing additional ﬂexibility in conﬁguring the Cisco MFT VWIC3s for supporting T1,

fractional T1, E1, and fractional E1 for both voice and WAN applications. All MFT VWIC3 modules include the drop-

and-insert multiplexing capability, which eliminates costly external third-party channel service units/data service units

(CSUs/DSUs) and drop-and-insert multiplexers.

Data Sheet

The Cisco MFT VWIC3 cards are oﬀered in single-, dual- and quadruple-port versions, which can be used and then

redeployed as network requirements change, thereby addressing several applications:

● T1/E1 data: The Cisco 1-, 2- and 4-port T1/E1 MFT VWIC3 versions act as a WIC, supporting T1, fractional

T1, E1, (including structured G.703 with G.704 framing), fractional E1, and E1structured G.703 applications.

To simplify remote management, these MFT VWIC3 cards integrate a fully managed DSU/CSU for T1

deployments and a fully managed DSU for E1 deployments.

● E1/G.703 data: The Cisco 1- and 2- port G.703 MFT VWIC3 versions act as a WIC, supporting T1, fractional

T1, E1 (including structured G.703 with G.704 framing), fractional E1, and unstructured E1 (G.703)

applications. To simplify remote management, the G.703 version includes a fully managed DSU. The G.703

versions also support all the capabilities on the T1/E1 versions.

● T1/E1 packet voice: The Cisco 1-, 2- and 4-port T1/E1 MFT VWIC3 (voice and WAN) versions act as a VIC,

supporting packet voice applications by providing T1, fractional T1, E1, and fractional E1 connections to

private branch exchanges (PBXs) and central oﬃces, thereby enabling new services and reducing voice and

fax toll charges.

● Mixed data and packet voice: The Cisco MFT VWIC3 interface cards can simultaneously support both data

and voice, reducing the complexity and number of network components and facilitating a graceful migration to

bandwidth-eﬃcient packet voice.

● Mixed data and packet voice with drop and insert: The Cisco MFT VWIC3 cards can be deployed as a

T1/E1 drop-and-insert multiplexer with integrated DSUs/CSUs, reducing the complexity of the network and

the cost of the central-oﬃce ports by efﬁciently combining time-division multiplexing (TDM) voice (PBX), IP

voice, and data on the same trunks. Cisco 1900, 2900 and 3900 ISR routers support drop and insert between

ports over a single MFT VWIC3 card and two ports over two diﬀerent MFT VWIC3s

Key Beneﬁts

Reduces Networking Lifecycle Costs

● Enables graceful migration from data-only to multiplexed data and voice to packetized voice applications

● Reduces training, deployment, management, and sparing inventory over single-purpose interfaces

● Maximizes investment protection

● Simpliﬁes network conﬁguration and sparing through the support of both T1 and E1 on the same card

● Oﬀers multifunction support for LAN-to-LAN routing, multiplexed data and voice, and packetized voice

● Oﬀers ability to share modules among Cisco 1900, 2900 and 3900 Series routers

● Increases conﬁguration ﬂexibility and reduces cost for data applications by allowing individual ports to be

clocked from independent clock sources (not supported for voice applications, since all voice enabled ports

must be clocked from a single clock source)

● Supports E1 conﬁgurations for both balanced and unbalanced modes

● Supports (G.703 models) unstructured E1 (G.703) for using the full 2.048 Mbps

● Eliminates costly external third-party CSUs/DSUs and drop-and-insert multiplexers

● Simpliﬁes remote network management by allowing a single management tool such as CiscoView or

CiscoWorks to support router, CSU/DSU, or drop-and-insert multiplexer

Maximizes System Resources

● Increases T1/E1 port density on the supported Cisco 2911, 2921, 2951, 3925, 3945, 3925E and 3945E

integrated services routers—up to four T1/E1 connections with an integrated CSU/DSU in a single EHWIC

slot

Data Sheet

● Oﬀers easy migration to bandwidth-eﬃcient packet voice, enabling new services

Customers can choose to integrate data and voice in stages to preserve their investment in WAN interfaces. For

example, the Cisco MFT VWIC3 can support data-only applications as a WAN interface, and then be reused to

integrate data and voice with the drop-and-insert multiplexer function or conﬁgured to support packetized voice

(voice over IP [VoIP] or voice over Frame Relay [VoFR]).

Applications

Packet Voice Solutions: PBX and Central-Oﬃce Connectivity

The Cisco MFT VWIC3 interface cards, through its digital T1/E1 ports, supply PBX and public-switched-telephone-

network (PSTN) connectivity for integrated services routers with the on-board EHWIC slots. The integrated services

routers support H.323-, Session Initiation Protocol (SIP)-, Media Gateway Control Protocol (MGCP)-, and Skinny

Client Control Protocol (SCCP)-based VoIP.

Data Solutions: 1- , 2- and 4-Port T1/E1 WIC with Integrated DSU/CSU

The Cisco MFT VWIC3 interface cards simplify branch-oﬃce connectivity by integrating the functions of a router,

T1/E1, and fractional T1/E1 serial interface with a fully managed DSU/CSU.

When used for “data-only” WAN connectivity, the Cisco MFT VWIC3 cards support numerous functions, including

Cisco IOS® Software Command-Line Interface (CLI)-initiated loopback control, similar to the popular 1 Port

T1/Fractional T1 DSU/CSU WAN Interface Card (part number HWIC-1DSU-T1. Additionally, the MFT VWIC3 is also

oﬀered in quadruple-port versions, enabling increased WAN port density in Cisco 2911, 2921, 2951 and Cisco 3900

Series routers. The T1/E1 MFT VWIC3 versions include integrated DSU functions for E1 deployments and integrated

CSU and DSU functions for T1 deployments, simplifying remote network management.

The Cisco 4-port MFT VWIC3 interface cards increase conﬁguration ﬂexibility on Cisco Systems

® integrated services

routers, eliminating the need for two dual-port T1/E1 HWICs. Increasing the T1/E1 port density in a single EHWIC

slot helps enable applications such as local serial aggregation with the 2-port high-speed serial WAN Interface Card

(part number HWIC-2T ), or ISDN backup with the 4 Port ISDN BRI S/T WAN Interface Card (part number HWIC-4B-

S/T) or the 1 port ISDN with NT-1 WAN Interface Card (part number HWIC-1B-U).

The Cisco MFT VWIC3 cards also support a channelized capability where the T1 or E1 service can be ﬂexibly split

into one or two fractional channel groups. Thus a single physical port can provide connection to multiple sites.

The Third-generation 1- and 2-port G.703 Multiﬂex Trunk voice/WAN Interface Cards (product numbers VWIC3-

1MFT-G703 and VWIC3-2MFT-G703) support not only unstructured E1 (G.703) but also all the features of the other

Cisco MFT VWIC3 cards, including drop and insert. Additional ﬂexibility is provided on the 2 port G.703 Multiﬂex

Trunk voice/WAN Interface Cards with the capability to conﬁgure one port for unstructured E1 (G.703) while

conﬁguring the other for standard framed E1.

Multiplexed Data and Voice Solutions: 2- and 4-Port T1/E1 Drop-and-Insert Multiplexer with Integrated

DSU/CSU

The Cisco 1-, 2- and 4-port MFT VWIC3 interface cards simplify branch-oﬃce connectivity by helping enable Cisco

2900 and 3900 routers to consolidate the functions of a router, a fully managed drop-and-insert multiplexer, and a

fully managed DSU/CSU into a single box. (It is possible to use two Cisco 1-port MFT VWIC3 interface cards for

supporting the drop-and-insert feature. Generally, a Cisco 2- or 4-port MFT VWIC3 is more appropriate because at

least 2 ports are required.) Typically a drop-and-insert multiplexer is used for channelized (that is, TDM) integration

of data and voice onto a single T1, fractional T1, E1, or fractional E1 connection to the central oﬃce. Sharing a line

can signiﬁcantly reduce costs over those of two separate physical lines to the central oﬃce. Although the normal use

Produktspezifikationen

Marke:	Cisco
Kategorie:	Netzwerkkarte / Adapter
Modell:	VWIC3-4MFT-T1/E1
Breite:	78.2 mm
Tiefe:	120.4 mm
Gewicht:	95 g
Höhe:	19.1 mm
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 85 %
Temperaturbereich bei Lagerung:	-25 - 70 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Kompatibilität:	Cisco 1921, 1941, 1941W, 2901, 2911, 2921, 2951, 3925, 3945, 3925E, 3945E
Anzahl der Verbinder:	4
Verbindungstyp:	RJ-45