Cisco Aironet 3702 Bedienungsanleitung

Cisco Zugangspunkt Aironet 3702

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Cisco Aironet 3702 (46 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/46

G ETTING S GTARTED UIDE

Cisco Aironet 3700 Series Access Points

1About this Guide

2Introduction to the Access Point

3Safety Instructions

4Unpacking

5Configurations

6Access Point Ports and Connectors

7Configuring the Access Point

8Mounting the Access Point

9Deploying the Access Point on the Wireless Network

10 Installing Modules

11 Troubleshooting

12 Declarations of Conformity and Regulatory Information

13 Configuring DHCP Option 43 and DHCP Option 60

14 Access Point Specifications

First Published: November, 2013, 78-21474-01

Last Updated: March 31, 2015

1 About this Guide

This Guide provides instructions on how to install and configure your Cisco Aironet 3700 Series

Access Point and how to install available radio modules. This guide also provides mounting

instructions and limited troubleshooting procedures.

The 3700 Series Access Point is referred to as the access point in this document.

2 Introduction to the Access Point

The 3700 series supports high-performing Spectrum Intelligence which sustains three spatial stream

rates over a deployable distance with high reliability when serving clients. The 3700 series provides

high reliability and overall wireless performance.

The 3700 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna

options. The access points support full inter-operability with leading 802.11ac clients, and support a

mixed deployment with other access points and controllers.

The 3700 series access point is a controller-based (Unified) product and supports:

•Simultaneous dual-band (2.4-GHz and 5-GHz) radios

•Integrated antennas on the 3702I access point model (AIR-CAP3702I-x-K9, AIR-AP3702I-UXK9)

•External antennas for rugged 3702E access point model (AIR-CAP3702E-x-K9,

AIR-AP3702E-UXK9)

Note The ‘x’ in the model numbers represents the regulatory domain. Model numbers

containing -UX, support the universal regulatory domain. For information on supported

regulatory domains, see “Regulatory Domains” section on page 7 for a list of supported

regulatory domains.

The features of the 3700 series are:

•Processing sub-systems (including CPUs and memory) and radio hardware which supports:

–

Network management

–

CleanAir—Automatic detection, classification, location and mitigation of RF interference

–

ClientLink 3.0 —BeamForming to 802.11a/g/n/ac clients.

–

VideoStream

–

Location

–

WIDS/WIPS

–

Security

–

Radio Resource Management (RRM)

–

Rogue detection

–

Management Frame Protection (MFP)

–

Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 1.3-Gbps

data-rates

•32 MB flash size

•802.11af/at

–

CDP (Cisco Discovery Protocol)

•2.4 GHz and 5 GHz 802.11n radios with the following features:

–

4TX x 4RX

–

3-spatial streams, 1.3-Gbps PHY rate

–

Spectrum intelligence

–

DPD (Digital Pre-Distortion) technology

–

Cisco Vector Beamforming

–

Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This product relies on the building’s installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than:

20A.

Statement 1005

Warning

Do not operate your wireless network device near unshielded blasting caps or in an

explosive environment unless the device has been modified to be especially qualified for

such use.

Statement 245B

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be

located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.

Statement 332

Caution The fasteners you use to mount an access point on a ceiling must be capable of

maintaining a minimum pullout force of 20 lbs (9 kg) and must use all 4 indented holes

on the mounting bracket.

Caution This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as defined by Environment A of the

IEEE 802.af Standard.

Note The access point is suitable for use in environmental air space in accordance with section

300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the

Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power

injector in air handling spaces.

Note Use only with listed ITE equipment.

4 Unpacking

To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the accessory kit from the shipping box.

Step 2 Return any packing material to the shipping container and save it for future use.

Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact

your Cisco representative or reseller for instructions.

–

The access point

–

Mounting bracket (selected when you ordered the access point)

–

Adjustable ceiling-rail clip (selected when you ordered the access point)

5 Configurations

The 3700 series access point contains two simultaneous dual-band radios, the 2.4-GHz MIMO radio

and the 5-GHz 802.11ac MIMO radio. The 3700 series access point configurations are:

•AIR-CAP3702E-x-K9, AIR-AP3702E-UXK9—two 2.4-GHz/5-GHz dual-band radios, up to 4

external dual-band diopole antennas

•AIR-CAP3702I-x-K9, AIR-AP3702I-UXK9—two 2.4-GHz/5-GHz dual-band radios, with

integrated dual-band inverted-F antennas

For information on the regulatory domains, see “Regulatory Domains” section on page 7.

External Antennas

The 3702E model is configured with up to four external dual-band dipole antennas, and two 2.4-GHz/

5-GHz dual-band radios. The radio and antennas support frequency bands 2400–2500 MHz and

5180–5865 MHz through a common dual-band RF interface. Features of the external dual-band

dipole antennas are:

•Four RTNC antenna connectors on the top of the access point

•Four TX/RX antennas

These antennas are supported on the 3702E:

•AIR-ANT2524DB-R

•AIR-ANT2524DW-R

•AIR-ANT2524DG-R

•AIR-ANT2524V4C-R

•AIR-ANT2544V4M-R

•AIR-ANT2566P4W-R

Internal Antennas

The 3702I model access point is configured with four dual-band inverted-F antennas, and two

2.4-GHz/5-GHz dual-band radios.

There are four antennas deployed inside the access point with one deployed on each corner of the

3702I access point top housing. Each antenna covers both the 2.4 GHz and the 5 GHz bands with a

single feed line. The basic features are as follows:

•Dual-band inverted-F antenna for use in both the 2.4-GHz and 5-GHz bands.

•Antenna unit integrated into the 3702I model access point.

•Peak gain is approximately 4 dBi in both the 2.4-GHz and 5-GHz bands.

Regulatory Domains

The 3700 series supports the following regulatory domains (shown as “x” in the model numbers):

•-A, -C, -D, -E, -H, -I, -K, -N, -Q, -R, -S, -T, -Z

The 3700 series also supports the universal regulatory domain, -UX, which has the following model

number formats:

•AIR-AP3702I-UXK9

•AIR-AP3702E-UXK9

Note For information on how to set the regulatory domain and country configurations of a

universal regulatory domain access point, see the Cisco Aironet Universal AP Priming and

Cisco AirProvision User Guide, at:

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g

.html

Countries Supported

Click this URL to browse to a list of countries and regulatory domains supported by the 3700:

www.cisco.com/go/aironet/compliance

6 Access Point Ports and Connectors

The 3702E model access point has external antenna connectors and the LED indictor on the top of the

model, as shown in . The 3702I model access point has inteFigure 1 grated antennas and does not have

external connectors on the top of the unit; however, it does have the LED indicator on top of the unit,

as shown in Figure 2.

Figure 1 Access Point Ports and Connections (top)—3702E Model

1Dual-band antenna connector A 3Dual-band antenna connector C

2Dual-band antenna connector B 4Dual-band antenna connector D

Figure 2 Access Point LED Indicator (top)—3702I Model

The ports and connections on the bottom of the access point are shown in Figure 3.

1LED indicator

Figure 3 Access Point Ports and Connections (bottom)-AIR3702E and 3702I Models

7 Configuring the Access Point

This section describes how to connect the access point to a wireless LAN controller. Because the

configuration process takes place on the controller, see the Cisco Wireless LAN Controller

Configuration Guide for additional information. This guide is available on Cisco.com.

The Controller Discovery Process

The access point uses standard Control and Provisioning of Wireless Access Points Protocol

(CAPWAP) to communicate between the controller and other wireless access points on the network.

CAPWAP is a standard, interoperable protocol which enables an access controller to manage a

1Kensington lock slot 4Console port

DC Power connection

Security padlock and hasp (padlock not

included)

3Gbit Ethernet port 6Mounting bracket pins (feet for desk or

table-top mount)

352029

1 2 3 4 5

•DHCP server discovery—This feature uses DHCP option 43 to provide controller IP addresses to

the access points. Cisco switches support a DHCP server option that is typically used for this

capability. For more information about DHCP option 43, see the “Configuring DHCP Option 43

and DHCP Option 60” section on page 40.

•DNS discovery—The access point can discover controllers through your domain name server

(DNS). For the access point to do so, you must configure your DNS to return controller IP

addresses in response to CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is

the access point domain name. Configuring the CISCO-CAPWAP-CONTROLLER provides

backwards compatibility in an existing customer deployment. When an access point receives an IP

address and DNS information from a DHCP server, it contacts the DNS to resolve

CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP

addresses, the access point sends discovery requests to the controllers.

Preparing the Access Point

Before you mount and deploy your access point, we recommend that you perform a site survey (or use

the site planning tool) to determine the best location to install your access point.

You should have the following information about your wireless network available:

•Access point locations.

•Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a

desktop.

Note You can mount the access point above a suspended ceiling but you must purchase

additional mounting hardware: See “Mounting the Access Point” section on page 17 for

additional information.

•Access point power options: power supplied by the recommended external power supply (Cisco

AIR-PWR-B), a DC power supply, PoE from a network device, or a PoE power injector/hub

(usually located in a wiring closet).

Note Access points mounted in a building’s environmental airspace must be powered using PoE

to comply with safety regulations.

Cisco recommends that you make a site map showing access point locations so that you can record the

device MAC addresses from each location and return them to the person who is planning or managing

your wireless network.

Installation Summary

Installing the access point involves these operations:

•Performing a pre-installation configuration (optional)

•Mounting the access point

•Grounding the access point

•Deploying the access point on the wireless network

Performing a Pre-Installation Configuration

The following procedures ensure that your access point installation and initial operation go as

expected. A pre-installation configuration is also known as priming the access point. This procedure

is optional.

Note Performing a pre-installation configuration is an optional procedure. If your network

controller is properly configured, you can install your access point in its final location and

connect it to the network from there. See the “Deploying the Access Point on the Wireless

Network” section on page 17 for details.

Pre-Installation Configuration Setup

The pre-installation configuration setup is shown in Figure 4.

Figure 4 Pre-Installation Configuration Setup

To perform pre-installation configuration, perform the following steps:

Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use

the CLI, web-browser interface, or Cisco WCS procedures as described in the appropriate

Cisco wireless LAN controller guide.

a. Make sure that access points have Layer 3 connectivity to the Cisco wireless LAN controller

Management and AP-Manager Interface.

b. Configure the switch to which your access point is to attach. See the Cisco Wireless LAN

Controller Configuration Guide, Release x.x for additional information.

c. Set the Cisco wireless LAN controller as the master so that new access points always join with

it.

d. Make sure DHCP is enabled on the network. The access point must receive its IP address

through DHCP.

e. CAPWAP UDP ports must not be blocked in the network.

f. The access point must be able to find the IP address of the controller. This can be

accomplished using DHCP, DNS, or IP subnet broadcast. This guide describes the DHCP

method to convey the controller IP address. For other methods, refer to the product

Controller

Layer 3

devices

Cisco Aironet

access points

272488

Step 4 If the pre-installation configuration is successful, the Status LED is green indicating normal

operation. Disconnect the access point and mount it at the location at which you intend to

deploy it on the wireless network.

Step 5 If your access point does not indicate normal operation, turn it off and repeat the

pre-installation configuration.

Note When you are installing a Layer 3 access point on a different subnet than the Cisco

wireless LAN controller, be sure that a DHCP server is reachable from the subnet on

which you will be installing the access point, and that the subnet has a route back to

the Cisco wireless LAN controller. Also be sure that the route back to the Cisco

wireless LAN controller has destination UDP ports 5246 and 5247 open for CAPWAP

communications. Ensure that the route back to the primary, secondary, and tertiary

wireless LAN controller allows IP packet fragments. Finally, be sure that if address

translation is used, that the access point and the Cisco wireless LAN controller have

a static 1-to-1 NAT to an outside address. (Port Address Translation is not

supported.)

8 Mounting the Access Point

Cisco Aironet 3702 series access points can be mounted in several configurations, including on a

suspended ceiling, on a hard ceiling or wall, on an electrical or network box, and above a suspended

ceiling. Click this URL to browse to complete access point mounting instructions:

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mounting/guide/apmount.html

9 Deploying the Access Point on the Wireless Network

After you have mounted the access point, follow these steps to deploy it on the wireless network:

Step 1 Connect and power up the access point.

Figure 5 Access Point LED Location

The access point status LED indicates various conditions and are described in Table 1.

1Status LED

Table 1 LED Status Indications

Message

Type

Status

LED

Message

Meaning

Boot loader status

sequence

Blinking green DRAM memory test in progress

DRAM memory test OK

Board initialization in progress

Initializing FLASH file system

FLASH memory test OK

Initializing Ethernet

Ethernet OK

Starting Cisco IOS

Initialization successful

352031

Association status Green Normal operating condition, but no wireless

client associated

Blue Normal operating condition, at least one wireless

client association

Operating status Blinking blue Software upgrade in progress

Cycling through green,

red, and off

Discovery/join process in progress

Rapidly cycling

through blue, green,

and red

Access point location command invoked

Blinking red Ethernet link not operational

Boot loader warnings Blinking blue Configuration recovery in progress (MODE

button pushed for 2 to 3 seconds)

Red Ethernet failure or image recovery (MODE

button pushed for 20 to 30 seconds)

Blinking green Image recovery in progress (MODE button

released)

Boot loader errors Red DRAM memory test failure

Blinking red and blue FLASH file system failure

Blinking red and off Environment variable failure

Bad MAC address

Ethernet failure during image recovery

Boot environment failure

No Cisco image file

Boot failure

Cisco IOS errors Red Software failure; try disconnecting and

reconnecting unit power

Cycling through blue,

green, red, and off

General warning; insufficient inline power

Table 1 LED Status Indications (continued)

Message

Type

Status

LED

Message

Meaning

Troubleshooting the Access Point Join Process

Access points can fail to join a controller for many reasons: a RADIUS authorization is pending;

self-signed certificates are not enabled on the controller; the access point’s and controller’s regulatory

domains don’t match, and so on.

Using the access point GUI, you can view join process failures in the AP Join Stats page. To view this

page, select Monitor > Statistics > AP Join, and then click the MAC address of the AP.

Alternatively, you can use the following CLI command to get a list of all APs that attempted to join

the controller:

show ap join stats summary all

To view details of a join process failure, use the following command:

show ap join stats detailed <ap base radio MAC address>

Controller software enables you to configure the access points to send all CAPWAP-related errors to

a syslog server. You do not need to enable any debug commands on the controller because all of the

CAPWAP error messages can be viewed from the syslog server itself.

The state of the access point is not maintained on the controller until it receives a CAPWAP join

request from the access point. Therefore, it can be difficult to determine why the CAPWAP discovery

request from a certain access point was rejected. In order to troubleshoot such joining problems

without enabling CAPWAP debug commands on the controller, the controller collects information for

all access points that send a discovery message to it and maintains information for any access points

that have successfully joined it.

The controller collects all join-related information for each access point that sends a CAPWAP

discovery request to the controller. Collection begins with the first discovery message received from

the access point and ends with the last configuration payload sent from the controller to the access

point.

You can view join-related information for up to three times the maximum number of access points

supported by the platform for the 2500 series controllers and the Controller Network Module within

the Cisco 28/37/38xx Series Integrated Services Routers.

Note The maximum number of access points varies for the Cisco WiSM2, depending on which

controller software release is being used.

When the controller is maintaining join-related information for the maximum number of access points,

it does not collect information for any more access points.

An access point sends all syslog messages to IP address 255.255.255.255 by default when any of the

following conditions are met:

12 Declarations of Conformity and Regulatory Information

This section provides declarations of conformity and regulatory information for the Cisco Aironet

3700 Series Access Points and any additional modules that can be installed into the Cisco Aironet 3700

Series Access Point. You can find additional information at this URL:

www.cisco.com/go/aironet/compliance

Manufacturers Federal Communication Commission Declaration of

Conformity Statement

Manufacturer:

Access Point Models Certification Number

AIR-CAP3702E-A-K9

AIR-CAP3702I-A-K9

AIR-SAP3702E-A-K9

AIR-SAP3702I-A-K9

LDK102087

AIR-CAP3702E-B-K9

AIR-CAP3702I-B-K9

AIR-SAP3702E-B-K9

AIR-SAP3702I-B-K9

AIR-AP3702I-UXK9

AIR-AP3702E-UXK9

Module Models Certification Number

AIR-RM3010L-UXK9 LDK102094

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

This device complies with Part 15 rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

This device operates in the 5150-5250MHz and 5470-5725MHz bands and is therefore restricted to

indoor operation only per FCC guidance.

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a residential environment. This

equipment generates, uses, and radiates radio frequency energy, and if not installed and used in

accordance with the instructions, may cause harmful interference. However, there is no guarantee that

interference will not occur. If this equipment does cause interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to correct the

interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician.

Caution The Part 15 radio device operates on a non-interference basis with other devices operating

at this frequency when using the integrated antennas. Any changes or modification to the

product not expressly approved by Cisco could void the user’s authority to operate this

device.

Caution Within the 5.15 to 5.25 GHz and 5.47-5.725 GHz bands, this device is restricted to

indoor operations to reduce any potential for harmful interference to co-channel Mobile

Satellite System (MSS) operations.

VCCI Statement for Japan

Warning

This is a Class B product based on the standard of the Voluntary Control

Council for Interference from Information Technology Equipment (VCCI). If this

is used near a radio or television receiver in a domestic environment, it may

cause radio interference. Install and use the equipment according to the

instruction manual.

Statement 371—Power Cable and AC Adapter

English Translation

When installing the product, please use the provided or designated connection cables/power cables/AC

adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and

Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code)

for any other electrical devices than products designated by CISCO. The use of cables that are certified

by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited

to CISCO-designated products.

Industry Canada

Canadian Compliance Statement

Access Point Models Certification Number

AIR-CAP3702E-A-K9

AIR-CAP3702I-A-K9

AIR-SAP3702E-A-K9

AIR-SAP3702I-A-K9

2461B-102087

AIR-AP3702I-UXK9

AIR-AP3702E-UXK9

Module Models Certification Number

AIR-RM3010L-UXK9 2461B-102094

Produktspezifikationen

Marke:	Cisco
Kategorie:	Zugangspunkt
Modell:	Aironet 3702

Brauchst du Hilfe?

Wenn Sie Hilfe mit Cisco Aironet 3702 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Zugangspunkt Cisco

Cisco Aironet 3700P Bedienungsanleitung

11 Oktober 2024

Cisco Aironet 1815m Bedienungsanleitung

8 Oktober 2024

Cisco AIR-CAP702I-I-K9 Bedienungsanleitung

4 Oktober 2024

Cisco Meraki MR72 Bedienungsanleitung

19 September 2024

Cisco Aironet 1552H Bedienungsanleitung

12 August 2024

Cisco Aironet 3700E Bedienungsanleitung

9 August 2024

Cisco Aironet 6021 Bedienungsanleitung

9 August 2024

Cisco AIR-AP1840I-I-K9 Bedienungsanleitung

7 August 2024

Cisco AIR-CAP1702I-E-K9 Bedienungsanleitung

5 August 2024

Cisco Aironet 1041N Bedienungsanleitung

4 August 2024

Bedienungsanleitung Zugangspunkt

Neueste Bedienungsanleitung für -Kategorien-

Netgear WAX210 Bedienungsanleitung

2 Dezember 2024

DrayTek VigorAP 920R Bedienungsanleitung

13 Oktober 2024

TP-Link Festa F65-Wall Bedienungsanleitung

4 Oktober 2024

EnGenius ENH200 Bedienungsanleitung

1 Oktober 2024

Mikrotik OmniTIK 5 PoE ac Bedienungsanleitung

1 Oktober 2024

Dell PowerConnect W-IAP3WNP Bedienungsanleitung

29 September 2024

Mikrotik Cube Lite60 Bedienungsanleitung

28 September 2024

D-Link DWL-1000AP+ Bedienungsanleitung

24 September 2024

Mikrotik hAP ac² Bedienungsanleitung

24 September 2024

D-Link DWL-700AP Bedienungsanleitung

22 September 2024