Chief SLM2220 Bedienungsanleitung

Chief Beamerzubehör SLM2220

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief SLM2220 (1 Seiten) in der Kategorie Beamerzubehör. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8850-000148 RevB

a Duchossois Group Company

05/09

SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets

SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information. Unpack carton and verify kit contents. If any listed parts are

missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled

locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket

installation.

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down.

3. Place interface bracket onto bottom of projector with three threaded inserts face up and two towards front of projector. Secure interface bracket to

projector using selected screw for model of projector (countersink screw or pan head screw).

4. Countersink screw in center countersink hole and pan head mounting screw in flush mounting hole. Your projector may require one or three

spacers for aligning bracket flat to projector. (Some models may suspend over bottom and have space between bracket and projector.)

Hitachi CP-X270W

1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .190 x 1/2" and 1/2" x .190 x 3/8" on top of each other and

centered over right threaded insert in front of projector. Using two 1/2" x .218 x 1/4" ,1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers, stack and

place them over three threaded inserts on left.

2. Place interface bracket onto projector and align spacers and mounting holes.

3. Position and align interface bracket to projector using M4 x 30mm countersink screw in middle of bracket, M4 x 30mm Phillips pan head screw in

right of bracket, and M4 x 16mm Phillips pan head screw in left of bracket. Tighten all fasteners at this time, securing the bracket to the projector.

Hitachi CP-S307W, CP-X380W, CP-X385W

1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers on top of each other