Chief SLM195 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief SLM195 (1 Seiten) in der Kategorie Beamerzubehör. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000264
8/16/07
SLB-195 and SLM-195 Interface Brackets
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector lining up the four out side holes in the bracket with the four threaded inserts in
the bottom of the projector.
4. Slide the nylon spacer between bracket and the projector, lining it up with the front mounting hole in the bracket.
5. Place the four M4 X 12mm mounting screws and M4 washers in the four out side holes and the M4 X 25mm mounting screw and M4
washer in the front mounting hole and through the nylon spacer by hand, secure all five fasteners at this time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (4) Screw, Phillips Pan Head, M4 x 12mm
(6) 10-24 Thumb Nuts ** (1) Screw, Phillips Pan Head, M4 x 25mm
(1) All-Points Security Kit (5) Washer, Flat , M4
(1) Spacer, Nylon, .500" x .257 x .625"
**Only used when installing SLB Interface brackets.
SLB-195
SLM-195
Front of Projector Front of Projector


Produktspezifikationen

Marke: Chief
Kategorie: Beamerzubehör
Modell: SLM195

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chief SLM195 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Beamerzubehör Chief

Bedienungsanleitung Beamerzubehör

Neueste Bedienungsanleitung fĂĽr -Kategorien-