Chief CPA262 Bedienungsanleitung

Chief Beamerzubehör CPA262

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief CPA262 (4 Seiten) in der Kategorie Beamerzubehör. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

I N S T A L L A T I O N I N S T R U C T I O N S

CPA to Male NPT Adapter Accessory

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

CPA262

CPA262 Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components located within the mounting system of the

CPA262 does not exceed 500 lbs (226.8 kg).

• The weight capacity of the CPA262 may be LIMITED to

the lowest weight capacity of any other component or

accessory used within the mounting system.

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is

damaged. Return the mounting system to a service center for

examination and repair.

WARNING: Do not use this product outdoors.

NOTE: Accessory is intended to be used with the UL Listed

CPA Extension Column Series and a 1-1/2" NPT or

NPSM following ANSI/ASME B1.20.1 (Schedule 40,

0.154" minimum thickness aluminum-ASTM B221)

threaded extension column (not included).

--SAVE THESE INSTRUCTIONS--

DIMENSIONS

0.38

9.5

0.34

8.6

2.88

73.2

2.25

57.2

4.25

108.0

DIMENSIONS: INCHES

[MILLIMETERS]

Installation Instructions CPA262

TOOLS REQUIRED FOR INSTALLATION / PARTS

A (1)

[CPA262 Coupler]

B (4)

5/16-18 x 1"

D (4)

5/16"

1/2"

nut driver

1/2"

C (4)

5/16"

INSTALLATION

IMPORTANT ! : The following procedure assumes that

UL Listed CPA Extension Column Series

has been

properly installed following instructions provided with

extension column.

NOTE:

The CPA262 adapts a UL Listed CPA Extension Column

Series (not included); to a 1-1/2" NPT or NPSM following

ANSI/ASME B1.20.1 (Schedule 40, 0.154" minimum

thickness aluminum-ASTM B221) threaded extension

column (not included).

1. Slide CPA262 (A) onto installed UL Listed CPA Extension

Column, lining up holes in CPA262 with holes in extension

column.

2. Install four 5/16" x 1" self-tapping screws (B) through four

5/16" split lock washers (C), four flat washers (D), and into

installed extension column.

NOTE: Installation of hex head self-tapping screws will be

easier when screws are carefully aligned with holes in

extension column, and a drill and nut driver is used. If a

drill will NOT be used, a small amount of pressure will

be needed to get the self-tapping screws started.

Figure 1

3. Install

1-1/2" NPT or NPSM following ANSI/ASME B1.20.1

(Schedule 40, 0.154" minimum thickness aluminum-ASTM

B221) threaded extension column (not included)

following

instructions included with extension column.

(B) x 4

5/16" holes -- 1/2" apart

(on each side of CPA262)

(D) x 4

Produktspezifikationen

Marke:	Chief
Kategorie:	Beamerzubehör
Modell:	CPA262
Gewicht:	410 g
Produkttyp:	Gewindeadapter
Produktfarbe:	Black, Silver, White
Höhe:	108 mm
Zertifizierung:	UL
Menge pro Packung:	1 Stück(e)
Durchmesser:	57.2 mm
Kompatibilität:	CPA