Chief CMS0203 Bedienungsanleitung

Chief Beamerzubehör CMS0203

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief CMS0203 (4 Seiten) in der Kategorie Beamerzubehör. Dieser Bedienungsanleitung war für 81 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

CMS SERIES COLUMNS

Fixed and Adjustable Length Columns

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

DEFINITIONS

MOUNTING SYSTEM: A MOUNTING SYSTEM is the

primary Chief product to which an accessory and/or component

is attached.

ACCESSORY: AN ACCESSORY is the secondary Chief

product which is attached to a primary Chief product, and may

have a component attached or setting on it.

COMPONENT: A COMPONENT is an audiovisual item

designed to be attached or resting on an accessory or mounting

system such as a video camera, CPU, screen, display,

projector, etc.

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all accessories are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this accessory can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this accessory is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

accessory.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to the CMS Series Extension

Column does not exceed 500 lbs (226 kg).

• The weight capacity of the CMS Series Extension

Columns may be LIMITED to the lowest weight

capacity of any other component, accessory or

mounting system used with this accessory.

WARNING: Do not use this product outdoors.

WARNING: Use this accessory only for its intended use as

described in these instructions. Do not use attachments not

recommended by the manufacturer.

WARNING: Never operate this accessory if it is damaged.

Return the accessory to a service center for examination and

repair.

NOTE: Chief CMS Series extension columns are Listed for use

with all Listed Chief ceiling plates and mounts specified

for use with 1-1/2" NPT following ANSI/ASME B1.20.1

(Schedule 40, 0.154" minimum thickness, steel or

aluminum - ASTM B221) extension columns and the

UL listed truss ceiling adapter accessory CMS380.

CMS Series extension columns are suitable for a

maximum 500 lbs (226 kg).

--SAVE THESE INSTRUCTIONS--

TOOLS REQUIRED

5/32" - security 3/16"

(included with

adjustable columns)

(included with

adjustable columns)

PARTS

[CMS adjustable length]

A (1)

[CMS fixed length]

B (1)

C (1)

5/16" x 5/8"

D (1)

5/16" E (1)

5/16"

F (2)

5/16" x 1/4" H (2)

5/16" x 1/4"

(security)

G (1)

5/32"

A (1)

(security)

J (1)

3/16"

NOTE: Parts B-J are only included with adjustable length

columns.

Installation Instructions

FIXED LENGTH EXTENSION COLUMN

IMPORTANT ! : The following procedure assumes that

the ceiling plate/adapter (not included) has been properly

installed following instructions provided with ceiling plate/

adapter.

NOTE: Intended for use with Chief accessories and mounts.

1. Install 1-1/2" NPT threaded column (A) into plate/adapter

(See Figure 1). Securely tighten column.

• Ensure column (A) engages four full threads into

plate/adapter.

• Ensure cable access opening is rotated to desired

position (optional installation).

NOTE: Cable access opening provided on columns 9" or

longer (229mm) in length. Optional installation used

when cables must exit below plate/adapter.

Figure 1

2. Secure column (A) by tightening set screw in plate/adapter

(See Figure 1).

NOTE: Hex key and set screw provided with plate/adapter.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to the CMS Series Extension

Column does not exceed 500 lbs (226 kg).

• The weight capacity of the CMS Series Extension

Columns may be LIMITED to the lowest weight

capacity of any other component or accessory used

within the mounting system.

3. Install and secure projector/display mount (not included) to

lower end of column (A) following instructions included with

mount.

ADJUSTABLE LENGTH EXTENSION

COLUMN

IMPORTANT ! : The following procedure assumes that

the ceiling plate/adapter (not included) has been properly

installed following instructions provided with ceiling plate/

adapter.

NOTE: Intended for use with Chief accessories and mounts.

1. Install 1-1/2" NPT threaded column (A or B, as applicable)

into plate/adapter (See Figure 2). Securely tighten column.

• Ensure column (A or B, as applicable) engages four full

threads into plate/adapter.

• Ensure cable access opening is rotated to desired

position (optional installation, column (A)).

NOTE: Cable access opening provided on columns 9" or

longer (229mm) in length. Optional installation used

when cables must exit below plate/adapter.

Figure 2

2. Secure column (A or B, as applicable) by tightening set

screw in plate/adapter (See Figure 2).

NOTE: Hex key and set screw provided with plate/adapter.

3. Install mating column (A or B, as applicable) (See Figure 2).

4 x

Installation Instructions

4. Using key (J), loosely install screw (C) through lock washer

(D), flat washer (E), and outer column (B) into adjustment

hole in inner column (A) (See Figure 3).

NOTE: Two adjustment holes provided in columns 6" or longer

(152mm) in length. Either adjustment hole can be used

to provide 1" (25mm) adjustment increments.

NOTE: Optional installation similar; not shown.

Figure 3

5. Adjust column (A or B, as applicable) to desired length, then

rotate and lock into position (See Figure 3).

NOTE: Any locking slot can be used to provide 2" (51mm)

adjustment increments.

6. Tighten screw (C) using key (J) (See Figure 3).

7. Install and tighten set screws (standard (F) or security (H),

as desired) using key (G) (See Figure 4).

NOTE: Optional installation similar; not shown.

Figure 4

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to the CMS Series Extension

Column does not exceed 500 lbs (226 kg).

• The weight capacity of the CMS Series Extension

Columns may be LIMITED to the lowest weight

capacity of any other component, accessory or

mounting system used with this accessory.

8. Install and secure projector/display mount (not included) to

lower end of column (A or B, as applicable) following

instructions included with mount.

CDE

F x 2

H x 2

Produktspezifikationen

Marke:	Chief
Kategorie:	Beamerzubehör
Modell:	CMS0203
Breite:	59 mm
Tiefe:	59 mm
Gewicht:	2270 g
Produktfarbe:	Schwarz
Höhe:	914 mm
Material:	Metall
Höchstgewichtskapazität:	226.79 kg
Zertifizierung:	TÜV, UL, TAA
Warentarifnummer (HS):	85299097
Formfaktor:	24 - 36" (609.6 - 914.4 mm)
Kompatibilität:	Speed-Connect
Markenkompatibilität:	Chief